Juniper SSR130 User manual
Quick Start
SSR130
IN THIS GUIDE
Step 1: Begin | 1
Step 2: Up and Running | 15
Step 3: Keep Going | 16
Step 1: Begin
IN THIS SECTION
Meet the SSR130 | 2
Claim Your Device | 2
Add the Network | 4
Add an Applicaon | 6
Create a Template | 7
Create Policies | 11
Assign the Template to a Site | 13
Assign the SSR130 to a Site | 14
This guide walks you through the simple steps to get a new cloud-ready SSR130 up and running in the Juniper Mist AI
cloud portal. You can onboard a single device using your mobile phone, or one or more devices using your computer.
Once onboarded, we'll walk you through the steps to create a basic conguraon.
You'll need a Juniper Mist WAN Assurance subscripon and your login credenals for the Juniper Mist portal.
Meet the SSR130
The Juniper Networks SSR130 network appliance is part of the SSR porolio. The SSR130 features four 1 GbE ports,
two 1 GbE RJ-45/SFP combo ports, 8 GB of memory, and a 120 GB enterprise-grade solid-state drive (SSD) for storage.
The SSR130 runs the FIPS 140-2 Level 1 compliant Session Smart Router (SSR) soware, which provides secure and
resilient WAN connecvity.
The SSR130 is available in models with or without LTE support.
Claim Your Device
IN THIS SECTION
Scan the QR Code | 3
Enter the Mist Claim Code | 4
To add the SSR130 to your organizaon's WAN Edge inventory, you'll need to enter the SSR130 claim informaon into
Mist. Locate the claim label on the rear panel.
There are two ways to enter the device claim informaon into Mist. Choose the method that is best for you.
• Scan the QR code with the MistAI app
• Manually enter the claim code in Mist
2
Enter the Mist Claim Code
1. Log in to your Mist organizaon's dashboard.
2. Navigate to your organizaon's inventory, and select the WAN tab at the top.
3. Select the Claim WAN Edges buon in the upper right of the inventory screen.
4. Add the claim code into the list of devices to claim.
5. Clear the Assign claimed WAN edges to site check box. This places the SSR into inventory, to be assigned to a site
later.
6. Click the Claim buon to claim the SSR into your inventory.
Onboarding Complete!
Fantasc, the SSR130 is in your inventory! To provision the SSR130 with ZTP, log in to Mist and connue with WAN
conguraon.
Add the Network
To begin your WAN design, idenfy the network the SSR will use to access applicaons over a LAN network segment.
4
1. From the Mist dashboard, navigate to the WAN secon of the organizaon sidebar menu, and select Networks.
2. Select Add Networks in the upper right.
3. Give the network a name.
5
4. Congure the network subnet as 192.168.1.0/24.
5. Click Save at the boom of the Edit Network side panel.
Excellent! You have now dened this network for use across the enre organizaon, including the template you will
apply to your new SSR130.
Add an Applicaon
SUMMARY
Next, dene the applicaons for the WAN to deliver, starng with the Internet.
1. Navigate back to the WAN secon of the organizaon sidebar menu, and select Applicaons.
2. Select Add Applicaons in the upper right.
3. Name the applicaon Internet.
6
4. Enter 0.0.0.0/0, or an IPv4 address space in the IP Addresses conguraon.
5. Click Save at the boom of the Add Applicaon side panel.
Nice! Your organizaon is set up to provide access to the Internet using the WAN.
Create a Template
IN THIS SECTION
Dene the WAN Port | 9
Dene the LAN Port | 10
So far you have an SSR device waing to be claimed, a network for your LAN, and an Internet applicaon for your WAN
to deliver. Next, you need to create a WAN Edge template that es them all together. Templates provide a re-usable and
consistent conguraon for every SSR you deploy.
1. Navigate back to the WAN secon of the organizaon sidebar menu, and select WAN Edge Templates.
7
2. Select Create Template in the upper right.
3. Name the template.
4. Click Create.
8
5. Enter NTP and DNS informaon to be used by the WAN edge device.
Dene the WAN Port
The rst thing to do in your template is to dene which port to use for the WAN.
1. Scroll to the WAN secon of the template, and select Add WAN.
2. Name the WAN port wan1.
3. Since you already plugged port 0 on the SSR130 into the Internet, enter ge-0/0/0 to designate it as a WAN port.
4. Make sure IP Conguraon is set to DHCP, and that Source NAT is enabled.
9
5. Click Add at the boom of the Edit WAN Conguraon side panel.
Dene the LAN Port
Next, associate your LAN with the appropriate port on the SSR, and give the LAN addional network services such as
DHCP.
1. Scroll to the LAN secon of the template, and select Add LAN.
2. From the Network drop-down menu, select your network segment to associate it with the LAN.
3. Enter the port used for the LAN port, for example ge-0/0/3.
4. Enter 192.168.1.1 as the IP Address to assign the WAN edge device .1 as a gateway in the network.
10
Other manuals for SSR130
1
Table of contents
Other Juniper Network Hardware manuals
Juniper
Juniper SRX5400 Service manual
Juniper
Juniper SRX300 Series User manual
Juniper
Juniper SSR130 Installation instructions
Juniper
Juniper CSE2000 Manual
Juniper
Juniper CTP2000 Series User manual
Juniper
Juniper JRR200 User manual
Juniper
Juniper MX480 Installation instructions
Juniper
Juniper EX8208 User manual
Juniper
Juniper SSR120 Installation instructions
Juniper
Juniper STRM 500 II Manual
Juniper
Juniper EX9200 Series User manual
Juniper
Juniper Day One+ ACX7100-48L User manual
Juniper
Juniper SSR1300 User manual
Juniper
Juniper M-Series User manual
Juniper
Juniper CTP2000 Series Installation instructions
Juniper
Juniper NFX250 User manual
Juniper
Juniper DUAL-PORT T1-E1 GPIMS User manual
Juniper
Juniper SRX340 Installation instructions
Juniper
Juniper BTI7800 Series Installation guide
Juniper
Juniper PTX3000 User manual
Popular Network Hardware manuals by other brands
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL product manual
B&B Electronics
B&B Electronics ZXT9-IO-222R2 product manual
Yudor
Yudor YDS-16 user manual
D-Link
D-Link ShareCenter DNS-320L datasheet
Samsung
Samsung ES1642dc Hardware user manual
Honeywell Home
Honeywell Home LTEM-PV Installation and setup guide
