Juniper TCX1000 User manual

TCX1000 Programmable ROADM

Quick Start Guide

December 2018

Part Number: 530-077883

Revision 03

This document describes how to install and connect the Juniper Networks®TCX1000

Programmable reconfigurable optical add/drop multiplexer (ROADM).

Contents AboutThisQuickStartGuide..........................................2

Step 1: Prepare Your Site for the TCX1000-RDM20 . . . . . . . . . . . . . . . . . . . . . . . . . 2

Step2:UnpacktheTCX1000-RDM20...................................3

Step3:MounttheTCX1000-RDM20....................................3

Step 4: Connect the TCX1000-RDM20 Grounding Cable . . . . . . . . . . . . . . . . . . . . 5

Step 5: Connect the TCX1000-RDM20 to a Management Console . . . . . . . . . . . . 6

Step6:PowerOntheTCX1000-RDM20..................................7

Connecting AC Power to the TCX1000-RDM20 . . . . . . . . . . . . . . . . . . . . . . . . 8

Connecting DC Power to the TCX1000-RDM20 . . . . . . . . . . . . . . . . . . . . . . . . 9

Step7:InstalltheOSCSFP............................................12

Step 8 Making a Craft Ethernet Port CLI Connection . . . . . . . . . . . . . . . . . . . . . . . 14

Step 9: Perform the Initial Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Step 10: Enabling OSC Forwarding on the TCX1000-RDM20 . . . . . . . . . . . . . . . . 18

SafetyWarningsSummary...........................................20

PowerCableWarning(Japanese)......................................21

TCX1000 Programmable ROADM Compliance Statements for NEBS . . . . . . . . . . 21

Compliance Statements for EMC Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Canada .......................................................22

EuropeanCommunity............................................22

Israel .........................................................22

Japan .........................................................22

UnitedStates...................................................22

TCX1000 Documentation and Release Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

RequestingTechnicalSupport.........................................23

Self-Help Online Tools and Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

OpeningaCasewithJTAC........................................24

RevisionHistory ....................................................25

About This Quick Start Guide

This Quick Start Guide contains information you need to install and set up the Juniper

Networks TCX1000-RDM20 Programmable ROADM. For complete installation

instructions, see the TCX1000 Programmable ROADM Hardware Guide at

https://www.juniper.net/documentation/.

WARNING: This Quick Start Guide contains a summary of safety warnings

in “Safety Warnings Summary” on page 20. For a complete list of warnings

for the TCX1000-RDM20, including translations, see the TCX1000

Programmable ROADM Hardware Guide at

https://www.juniper.net/documentation/.

The TCX1000-RDM20 is a standalone 20-port reconfigurable optical add/drop multiplexer

(ROADM) with removable AC or DC power supplies and cooling fans.

Step 1: Prepare Your Site for the TCX1000-RDM20

Before installing the TCX1000-RDM20, make sure your site meets all power,

environmental, and clearance requirements. See the site preparation guidelines in the

TCX1000 Programmable ROADM Hardware Guide.

NOTE: The TCX1000-RDM20 ships with two fan modules and two power

supplies installed.

Ensure that you have the following parts and tools available to install, connect power

to, and configure the TCX1000-RDM20:

•Eight self-tapping bolts to secure the chassis and mounting brackets to the rack

(provided).

•Power cords with plugs appropriate for your geographical location (provided with the

AC model).

•19-in. front and rear mounting brackets (attached to the chassis).

•(Optional) 21-in. and 23-in. front and rear mounting brackets (provided).

•Grounding lug, nut, and washers (provided).

•Two ring lugs (Panduit PN14-8R-C) for DC power (provided).

•One fiber management bracket (provided).

•Optical supervisory channel (OSC) kit (included with the TCX1000-RDM20-AC and

the TCX1000-RDM20-DC):

•Small form-factor pluggable (SFP)—100BASE-FX Ethernet, 1511 nm, 43 dB reach.

•Two 3-dB LC fixed optical attenuators.

TCX1000 Programmable ROADM Quick Start Guide

•LC/UPC duplex fiber patchcord—30-cm length, 2-mm jacket.

•Electrostatic discharge (ESD) grounding strap (not provided).

•Screwdriver appropriate for the rack-mounting screws (not provided).

•Power cable or cables appropriate for your geographical location available to connect

DC power to the TCX1000-RDM20-DC (not provided).

•Grounding cable (not provided).

•RJ-45 cable and RJ-45 to DB-9 serial port adapter (not provided).

•Management host, such as a PC laptop, with a serial port (not provided).

Step 2: Unpack the TCX1000-RDM20

For detailed instructions on how to unpack the box and verify the parts received, see the

TCX1000 Programmable ROADM Hardware Guide.

Step 3: Mount the TCX1000-RDM20

To mount the TCX1000-RDM20 on four posts in a rack using the 19-in. mounting brackets:

NOTE: The 19-in. front and rear brackets are attached to the

TCX1000-RDM20 when they are shipped. If you want to attach the 21-in. or

23-in. brackets, unscrew the 19-in. brackets from the chassis, and attach the

21-in. or 23-in. brackets by using the same screws.

NOTE: This procedure requires two persons. Do not attempt to do it alone.

1. Attach the ESD grounding strap to your bare wrist and to a site ESD point.

NOTE: Place the rack in its permanent location, allowing adequate

clearance for airflow and maintenance, and secure it to the building

structure. If you are mounting multiple units in the rack, mount the heaviest

unit at the bottom and mount the others from bottom to top in order of

decreasing weight. The TCX1000-RDM20 weighs 12.92 lb (5.86 kg).

2. Unscrew the 19-in. rear brackets from the chassis and set them aside, saving the

screws.

3. Position the TCX1000-RDM20 so the FRUs are next to the hot aisle.

4. Have one person grasp both sides of the chassis, lift it, and position it in the rack so

that the front bracket is aligned with the rack holes.

Step 2: Unpack the TCX1000-RDM20

5. Have a second person secure the front of the chassis to the rack using four mounting

screws (and cage nuts and washers if your rack requires them.) Tighten the screws.

See Figure 1 on page 4.

Figure 1: Installing the TCX1000-RDM20 on a Rack

6. Continue to support the chassis while sliding the rear brackets into the channel of the

side-mounting rails and securing the brackets to the rack. Use the four mounting

screws (and cage nuts and washers if your rack requires them) to attach each bracket

to the rack. Tighten the screws.

NOTE: The rear bracket is long enough to allow for various bracket depths.

7. Ensure that the chassis is level by verifying that all the screws on the front of the rack

are aligned with the screws at the back of the rack.

8. Secure the rear bracket to the chassis using the saved screws from Step 2.

9. Install the fiber management clip on the front of the chassis, on the right or left hand

side, as required. See Figure 2 on page 4.

Figure 2: Installing the Fiber Management Clip on the TCX1000-RDM20

TCX1000 Programmable ROADM Quick Start Guide

Step 4: Connect the TCX1000-RDM20 Grounding Cable

To meet safety and electromagnetic interference (EMI) requirements and to ensure

proper operation, you must connect the chassis to earth ground before you connect it to

power. For installations that require a separate grounding conductor to the chassis, use

the protective earthing terminal on the TCX1000-RDM20 chassis to connect to the earth

ground.

NOTE: An AC-powered TCX1000-RDM20 gains additional grounding when

you plug the power supply in the device into a grounded AC power outlet by

using an AC power cord appropriate for your geographical location.

CAUTION: Before you connect power to the TCX1000-RDM20, a licensed

electrician must attach a cable lug to the grounding and power cables that

you supply. A cable with an incorrectly attached lug can damage the

TCX1000-RDM20 (for example, by causing a short circuit).

NOTE: Mount the TCX1000-RDM20 in the rack or cabinet before attaching

the grounding lug to the TCX1000-RDM20.

Ensure that you have the following parts and tools available:

NOTE: The grounding point is located on the back of the TCX1000-RDM20

and is a #10-32 threaded stud.

•Grounding lug—Panduit LCA10-10F-L (provided) that accommodates 14-10 AWG

standard wire (not provided).

•Two #10 external tooth lock washers and one #10 hex nut (provided).

•Screwdriver appropriate for the screws (not provided).

•Electrostatic discharge (ESD) grounding wrist strap (not provided).

You ground the TCX1000-RDM20 by attaching a grounding cable to the chassis. See the

TCX1000-RDM20 Chassis Grounding Cable and Lug Specifications in the TCX1000

Programmable ROADM Hardware Guide.

Step 4: Connect the TCX1000-RDM20 Grounding Cable

To connect a grounding cable to the TCX1000-RDM20:

1. Attach an ESD grounding strap to your bare wrist, and connect the strap to an approved

site ESD grounding point. See the instructions for your site.

2. Connect one end of the grounding cable to a proper site earth ground, such as the

rack in which the TCX1000-RDM20 is mounted.

3. Strip the appropriate length of wire for the ground lug type used, and verify that a

licensed electrician has attached the cable lug provided with the TCX1000-RDM20

to the grounding cable.

4. Attach the grounding lug, lock washers, and hex nut as shown in Figure 3 on page 6.

Figure 3: Connecting a Grounding Cable to the TCX1000-RDM20

5. Dress the grounding cable and ensure that it does not touch or block access to other

device components and that it does not drape where people could trip over it.

Step 5: Connect the TCX1000-RDM20 to a Management Console

You can configure and manage the TCX1000-RDM20 by using a dedicated console. Use

the console port to connect the device directly to a management console, such as a

laptop, or a console server.

The TCX1000-RDM20 has a console port (labeled SERIAL) with a DB-9 connector.

Ensure that you have an RJ-45 to DB-9 rollover cable available.

TCX1000 Programmable ROADM Quick Start Guide

NOTE: If your laptop or PC does not have a DB-9 male connector pin and you

want to connect your laptop or PC directly to the TCX1000-RDM20, use a

combination of the RJ-45 cable and RJ-45 to DB-9 adapter and a USB to

DB-9 male adapter.

To connect the TCX1000-RDM20 to a management console:

1. Connect one end of the RJ-45 to DB-9 rollover cable to the console port (labeled

SERIAL). See Figure 4 on page 7 and Figure 5 on page 7.

2. Connect the other end of the cable directly to a management console or console

server.

Figure 4: Connecting the TCX1000-RDM20 Directly to a Management Console

Figure 5: Connecting the TCX1000-RDM20 to a Management Console Through a Console

Server

Step 6: Power On the TCX1000-RDM20

NOTE: The TCX1000-RDM20 is supplied with two factory-installed power

supplies, either AC or DC.

NOTE: We recommend the fuse or circuit protector value rated at 10 A for

both the TCX1000-RDM20-AC and the TCX1000-RDM20-DC.

•Connecting AC Power to the TCX1000-RDM20 on page 8

•Connecting DC Power to the TCX1000-RDM20 on page 9

Step 6: Power On the TCX1000-RDM20

Connecting AC Power to the TCX1000-RDM20

To connect AC power to a TCX1000-RDM20:

1. Prevent ESD damage to your equipment by attaching an ESD grounding strap to your

bare wrist, and then connecting the strap to an approved site ESD grounding point.

2. Ensure that the power supplies are fully inserted in the chassis and the latches are

secure.

3. Insert the coupler end of the power cord into the AC power cord inlet on the AC power

supply faceplate for each power supply.

4. If the AC power source outlet has a power switch, set it to the off (O) position.

NOTE: The TCX1000-RDM20 powers on as soon as power is provided to

the power supply.

5. Insert the power cord plug into an AC power source outlet for each power supply. See

Figure 6 on page 8.

Figure 6: Connecting an AC Power Cord to an AC Power Supply in a TCX1000-RDM20

6. If the AC power source outlet has a power switch, set it to the on (|) position.

7. Verify that the LEDs on each power supply are lit green. If any are lit yellow, remove

power from the power supply, and replace the power supply (see Installing a Power

Supply in a TCX1000-RDM20 in the TCX1000 Programmable ROADM Hardware Guide).

Do not remove the power supply until you have a replacement power supply ready;

power supplies must be installed in the TCX1000-RDM20 to ensure proper airflow.

CAUTION: Replace a failed power supply with a new power supply within

five minutes of removal to prevent chassis overheating.

TCX1000 Programmable ROADM Quick Start Guide

NOTE: Each power supply must be connected to a dedicated power source

outlet. We recommend connecting each power supply to a different power

source for redundancy purposes.

Connecting DC Power to the TCX1000-RDM20

WARNING: DC-powered TCX1000-RDM20 models are intended for

installation only in a restricted access location.

Before you begin connecting DC power to the TCX1000-RDM20:

•Read General Electrical Safety Guidelines and Warnings and TCX1000-RDM20 DC Power

Electrical Safety Guidelines in the TCX1000 Programmable ROADM Hardware Guide.

•Ensure that you have taken the necessary precautions to prevent electrostatic discharge

(ESD) damage (see Prevention of Electrostatic Discharge Damage in the TCX1000

Programmable ROADM Hardware Guide).

•Ensure that you have connected the TCX1000-RDM20 chassis to earth ground.

CAUTION: Before you connect power to the TCX1000-RDM20, a licensed

electrician must attach a cable lug to the grounding and power cables that

you supply. A cable with an incorrectly attached lug can damage the

ROADM (for example, by causing a short circuit).

NOTE: To meet safety and electromagnetic interference (EMI)

requirements and to ensure proper operation, you must connect the chassis

to earth ground before you connect it to power. For installations that require

a separate grounding conductor to the chassis, use the protective earthing

terminal on the TCX1000-RDM20 chassis to connect to the earth ground

(see Connecting the TCX1000-RDM20 Grounding Cable in the TCX1000

Programmable ROADM Hardware Guide).

CAUTION: You must ensure that power connections maintain the proper

polarity. The power source cables might be labeled (+) and (–) to indicate

their polarity. There is no standard color coding for DC power cables. The

color coding used by the external DC power source at your site determines

the color coding for the leads on the power cables that attach to the

terminals on each power supply.

•Ensure that you have the following parts and tools available:

•ESD grounding strap.

Connecting DC Power to the TCX1000-RDM20

•Power cable or cables appropriate for your geographical location available to connect

DC power to the TCX1000-RDM20.

NOTE: Each power supply must be connected to a dedicated power source

outlet. We recommend connecting each power supply to a different power

source for redundancy purposes.

To connect DC power to a TCX1000-RDM20:

1. Prevent ESD damage to your equipment by attaching an ESD grounding strap to your

bare wrist, and then connecting the strap to an approved site ESD grounding point.

2. Ensure that the power supplies are fully inserted in the chassis and the latches are

secure.

3. Ensure that the power source is turned off, the voltage across the DC power source

cable leads is 0 V, and there is no chance that the cable leads might become active

during installation.

4. Remove the plastic cover from the terminal block on the power supply. Remove the

terminal block screws.

5. Identify the positive and negative feed positions, as marked on the power supply.

6. Strip each of the wires coming out from the DC-input power source by 8-9 mm. Do

not strip more than required, because doing so can leave the wire exposed from the

DC connector after installation. The cable must be terminated with the supplied ring

lug (Panduit PN14-8R-C).

7. Insert the lug into the terminal block. See Figure 7 on page 10.

Figure 7: Attaching the Lug and Cable

TCX1000 Programmable ROADM Quick Start Guide

Other manuals for TCX1000

This manual suits for next models

Table of contents

Other Juniper Network Hardware manuals

Juniper

Juniper JATP700 Installation instructions

Juniper

Juniper PTX10004 Installation instructions

Juniper

Juniper NETSCREEN-5XP User manual

Juniper

Juniper IDP 800 User manual

Juniper

Juniper Junos Space JA1500 User manual

Juniper

Juniper WX 3400 User manual

Juniper

Juniper ACX7100 User manual

Juniper

Juniper SSR1500 Installation instructions

Juniper

Juniper Junos Space JA2500 Installation instructions

Juniper

Juniper NFX250 User manual

Juniper

Juniper NSM4000 Installation instructions

Juniper

Juniper Day One+ QFX5700 User manual

Juniper

Juniper 16-PORT GIGABIT ETHERNET XPIMS User manual

Juniper

Juniper Junos Space JA2500 Installation instructions

Juniper

Juniper SRX300 Series User manual

Juniper

Juniper T1600 User manual

Juniper

Juniper Day One+ User manual

Juniper

Juniper Day One+ QFX5120 User manual

Juniper

Juniper MX SERIES - FAN TRAY UPGRADE REV1 4-2010 User manual

Juniper

Juniper SSR120 Installation instructions

Juniper

Juniper JSA3800 Installation instructions

Juniper

Juniper NFX150-S1 User manual

Juniper

Juniper EX4100-48P/T User manual

Juniper

Juniper SRX320 User manual

Popular Network Hardware manuals by other brands

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL product manual

B&B Electronics

B&B Electronics ZXT9-IO-222R2 product manual

Yudor

Yudor YDS-16 user manual

D-Link

D-Link ShareCenter DNS-320L datasheet

Samsung

Samsung ES1642dc Hardware user manual

Honeywell Home

Honeywell Home LTEM-PV Installation and setup guide

evertz

evertz 7700 Series manual

D-Link

D-Link ShareCenter DNS-343 Quick installation guide

Asante

Asante AsanteBridge 1012 user guide

FireBrick

FireBrick FB2700 user manual

Audiovox Electronics

Audiovox Electronics ARWH2T user manual

ADC

ADC DSX-1 Operational Procedures Guide

NetComm

NetComm NF2 user guide

Alcatel-Lucent

Alcatel-Lucent 5620 user guide

Dell EMC

Dell EMC XC6420 Series Solution guide

Lanner

Lanner NCA-1020A user manual

Allied Telesis

Allied Telesis AT-TN121-A Specifications

Arista

Arista CCA-ETM-Q12 quick start guide