Juniper SRX5600 User manual

Replacing the SRX5600 Services Gateway Routing Engine

To replace the routing engine, perform the following procedures:

1. Removing the SRX5600 Services Gateway Routing Engine on page 1

2. Installing the SRX5600 Services Gateway Routing Engine on page 2

Removing the SRX5600 Services Gateway Routing Engine

CAUTION: Before you replace a Routing Engine, you must take the host subsystem

offline.

To remove the Routing Engine (see Figure 1):

1. Take the host subsystem offline as described in Taking the SRX5600 Services

Gateway Host Subsystem Offline.

2. Place an electrostatic bag or antistatic mat on a flat, stable surface.

3. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and

connect the strap to one of the ESD points on the chassis.

4. Flip the ejector handles outward to unseat the Routing Engine.

5. Grasp the Routing Engine by the ejector handles and slide it about halfway out

of the chassis.

6. Place one hand underneath the Routing Engine to support it and slide it

completely out of the chassis.

7. Place the Routing Engine on the antistatic mat.

Figure 1: Removing a Routing Engine

Replacing the SRX5600 Services Gateway Routing Engine ■1

Installing the SRX5600 Services Gateway Routing Engine

To install a Routing Engine into an SCB (see Figure 2):

1. If you have not already done so, take the host subsystem offline. See Taking the

SRX5600 Services Gateway Host Subsystem Offline.

2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and

connect the strap to one of the ESD points on the chassis.

3. Ensure that the ejector handles are not in the locked position. If necessary, flip

the ejector handles outward.

4. Place one hand underneath the Routing Engine to support it.

5. Carefully align the sides of the Routing Engine with the guides inside the opening

on the SCB.

6. Slide the Routing Engine into the SCB until you feel resistance, and then press

the Routing Engine's faceplate until it engages the connectors.

7. Press both of the ejector handles inward to seat the Routing Engine.

8. Tighten the captive screws on the right and left ends of the Routing Engine

faceplate.

9. Power-on the services gateway. The OK LED on the power supply faceplate should

blink, then light steadily.

The Routing Engine might require several minutes to boot.

After the Routing Engine boots, verify that it is installed correctly by checking the

RE0 and RE1 LEDs on the craft interface. If the services gateway is operational and

the Routing Engine is functioning properly, the green ONLINE LED lights steadily. If

the red FAIL LED lights steadily instead, remove and install the Routing Engine again.

If the red FAIL LED still lights steadily, the Routing Engine is not functioning properly.

Contact your customer support representative.

To check the status of the Routing Engine, use the CLI command:

user@host> show chassis routing-engine

Routing Engine status:

Slot 0:

Current state Master ...

For more information about using the CLI, see the JUNOS Software manuals.

2■Installing the SRX5600 Services Gateway Routing Engine

Figure 2: Installing the Routing Engine

Published: 2009-11-03

Installing the SRX5600 Services Gateway Routing Engine ■3

Other manuals for SRX5600

16

Table of contents

Other Juniper Network Hardware manuals

Juniper

Juniper EX9200 Series User manual

Juniper

Juniper JSA7800 User manual

Juniper

Juniper JRR200 Installation instructions

Juniper

Juniper PTX10004 Installation instructions

Juniper

Juniper Day One Plus SRX380 User manual

Juniper

Juniper BTI7800 Series Installation guide

Juniper

Juniper QFX10016 User manual

Juniper

Juniper Junos Space JA2500 Installation instructions

Juniper

Juniper NetScreen-5GT Wireless User manual

Juniper

Juniper TCX1000 User manual

Juniper

Juniper SSR1500 User manual

Juniper

Juniper STRM 500 II Manual

Juniper

Juniper SSR1400 Installation instructions

Juniper

Juniper MX104 User manual

Juniper

Juniper CTP1000 Series Installation instructions

Juniper

Juniper SRX320 User manual

Juniper

Juniper Junos OS User manual

Juniper

Juniper JSA7500 User manual

Juniper

Juniper Route Insight Manager User manual

Juniper

Juniper SSR1300 Installation instructions

Juniper

Juniper SRX300 Series Installation instructions

Juniper

Juniper JSA5800 Installation instructions

Juniper

Juniper SRX5400 Service manual

Juniper

Juniper Day One+ User manual

Popular Network Hardware manuals by other brands

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL product manual

B&B Electronics

B&B Electronics ZXT9-IO-222R2 product manual

Yudor

Yudor YDS-16 user manual

D-Link

D-Link ShareCenter DNS-320L datasheet

Samsung

Samsung ES1642dc Hardware user manual

Honeywell Home

Honeywell Home LTEM-PV Installation and setup guide

evertz

evertz 7700 Series manual

D-Link

D-Link ShareCenter DNS-343 Quick installation guide

Asante

Asante AsanteBridge 1012 user guide

FireBrick

FireBrick FB2700 user manual

Audiovox Electronics

Audiovox Electronics ARWH2T user manual

ADC

ADC DSX-1 Operational Procedures Guide

NetComm

NetComm NF2 user guide

Alcatel-Lucent

Alcatel-Lucent 5620 user guide

Dell EMC

Dell EMC XC6420 Series Solution guide

Lanner

Lanner NCA-1020A user manual

Allied Telesis

Allied Telesis AT-TN121-A Specifications

Arista

Arista CCA-ETM-Q12 quick start guide