Jacobsen SLF 1880 User manual

Technical Repair Manual

SLF 1880

Page Intentionally Blank

Technical Repair Manual

SLF 1880

WARNING: If incorrectly used this machine can cause sever injury. Those

who use and maintain this machine should be trained in its proper use,

warned of its dangers and should read the entire manual before attempting

to set up, operate, adjust or service the machine.

Litho in the U.S.A. 5/2011 Part Number 4171721 Rev B

Page Intentionally Blank

Forward

General

This manual provides detailed information and proce-

dures to safely repair and maintain the following:

Jacobsen® SLF1880™ fairway mower and associated

accessory attachments.

This manual is intended to introduce and guide the user

through the latest factory-approved troubleshooting

and repair techniques and practices.

Before you attempt to troubleshoot or make repairs,

you must be familiar with the operation of this machine.

Refer to the operator’s manual and parts manual for

specific information on these topics.

THE INFORMATION CONTAINED IN THIS MANUAL

IS BASED ON MACHINES MANUFACTURED UO TO

THE TIME OF PUBLICATION. JACOBSEN

RESERVES THE RIGHT TO CHANGE ANY OF THIS

INFORMATION WITHOUT NOTICE.

California

Proposition 65 Warning

Trademark Acknowledgement

Jacobsen acknowledges the following trademarks for

company names or products mentioned within this pub-

lication:

Lubriplate® Is a Trademark of Fiske Brothers Refining

Co.

Loctite® and Permatex® are trademarks of Henkel Cor-

poration.

WARNING

Certain vehicle components contain or emit

chemicals known to the state of California to

cause cancer and birth defects or other repro-

ductive harm.

Forward

How to Use This Manual

This manual is designed to provide multiple ways to

locate and access repair information.

Read each section in entirety before beginning a pro-

cedure. Proper understanding of machine operation

and components is the key to successful diagnostics

and repair.

Make use of special information features within this

manual in order to be better prepared to perform

repairs. Always follow manual procedures and safety

guidelines. Never take shortcuts.

Table of Contents

Major machine components or topics of interest are

separated into specific chapters. Each manual lists

these chapters in the main table of contents.

Chapter table of Contents

Each chapter begins with a detailed Table of Contents

related to the specific machine component or system.

Use the chapter Table of Contents to find specific com-

ponent or procedural information.

Required Tools and Material

Some procedures will require the use of specific tools

and/or materials. These tools and/or materials will be

listed for reference, prior to beginning a procedure.

Specifications

Near the beginning of each chapter is a specifications

listing. this listing contains any specifications contained

within the chapter.

Quick Reference Specifications

A list of all machine specifications can be found in

Chapter 1 “Specifications”. This is a list of all general

specifications. Detailed specifications will be listed in

the front of each chapter under “Specifications”.

Warning and Cautions

Warning and Caution indicators are located throughout

the manual at specific points of interest. These notices

are given to prevent personal injury, death and/or

equipment damage. Always heed these notices, and

practice common sense when performing any mainte-

nance or repair procedure.

Notes

Special notes are given in order to draw attention to

detailed instructions. These notes are intended to give

further important information regarding the machine

and/or a step in a procedure.

Troubleshooting

Troubleshooting charts are provided in each chapter to

aid in the diagnostic process. Use these suggestions to

aid in identifying a potential mechanical or machine

adjustment problem.

INTRODUCTION

CONTROLS

ENGINE

DRIVE TRAIN

BRAKE SYSTEM

STEERING

WHEELS AND TIRES

HYDRAULICS

CHASSIS

ELECTRICAL SYSTEM

PREVENTIVE MAINTENANCE

ATTACHMENTS

OPTIONS

MISCELLANEOUS

Page Intentionally Blank

INTRODUCTION

--1

SECTION 1

INTRODUCTION

1A General Information ........................................................................................................................................ 1

Contents................................................................................................................................................... 1

Index Numbers......................................................................................................................................... 1

Replacement Parts................................................................................................................................... 1

Specifications ........................................................................................................................................... 2

Serial Numbers ........................................................................................................................................ 4

General Cleaning ..................................................................................................................................... 4

Safety ....................................................................................................................................................... 4

Torque Values ........................................................................................................................................ 10