Infinova V6202-TA Series User manual

INSTRUCTION MANUAL

V6202-TA Series

HD 1MP and 2MP Low Light IP Camera

Notice

This manual may not be reproduced in any form or by any means to create any

derivative such as translation, transformation, or adaptation without the prior

written permission of Infinova.

Infinova reserves the right to change this manual and the specifications without

prior notice. The most recent product specifications and user documentation for

all Infinova products are available on our web site www.infinova.com.

Trademarks

Infinova

® is a trademark of Infinova.

All other trademarks that may appear belong to their respective proprietors.

FCC Warning

The V6202-TA series HD 1MP and 2MP low light IP cameras comply with the

FCC rules.

Operation is subject to the following two conditions:

 This device will not cause harmful interference.

 This device must accept any interference received, including interference

that may cause undesired operations.

The V6202-TA series HD 1MP and 2MP low light IP cameras have been tested

and found to comply with the limits for a Class A digital device, pursuant to the

FCC rules. With these rules and regulations being obeyed to maintain the good

working condition of device, the operation is not supposed to be affected by

external interruptions under certain circumstances. This device is

electromagnetic, so all the installation and application processing along the

device has to follow strictly to the manual or it may hamper the

telecommunication around. Meanwhile, there is no guarantee that interference

will not occur in a certain particular installation situation.

Read this manual carefully before installation. This manual

should be saved for future use.

Important Safety Instructions and Warnings:

 Electronic devices must be kept away from water, fire or high magnetic

radiation.

 Clean with a dry cloth.

 Provide adequate ventilation.

 Unplug the power supply when the device is not to be used for an extended

period of time.

 Only use components and parts recommended by manufacturer.

 Position power source and related wires to assure to be kept away from

ground and entrance.

 Refer to qualified personnel for all service matters.

 Save product packaging to ensure availability of proper shipping containers

for future transportation.

Indicate that the un-insulated components within the product may carry a

voltage harmful to humans.

Indicate operations that should be conducted in strict compliance with

instructions and guidelines contained in this manual.

Warning: To avoid risk of fire and electric shock, keep the product away

from rain and moisture!

CONTENTS

Chapter I System Introduction ................................................................ 1

1.1 Product Description............................................................................... 1

1.2 Product Features.................................................................................... 1

1.3 System Requirement ............................................................................. 2

1.4 Product Model....................................................................................... 3

1.5 Specifications........................................................................................ 3

1.6 Notice.................................................................................................... 5

Chapter II Installation and PORT INTRODUCTION........................... 7

2.1 Installation Precautions ......................................................................... 7

2.2 Back Panel and Control Parts................................................................ 7

2.3 Dimensions ........................................................................................... 9

2.4 Installation of Camera........................................................................... 9

Chapter III IE Browser Settings.............................................................11

3.1 Equipment Connection........................................................................ 11

3.2 Software Installation ........................................................................... 11

Chapter IV Basic Function Operation................................................... 14

4.1 Live View............................................................................................ 14

4.2 System ................................................................................................ 17

4.3 Network Settings................................................................................. 23

4.4 Camera Settings .................................................................................. 32

4.5 Audio & Video Settings ...................................................................... 39

4.6 PTZ Functions..................................................................................... 48

4.7 Alarm Settings..................................................................................... 49

4.8 Record Management ........................................................................... 51

4.9 Account Settings ................................................................................. 55

4.10 System Log ....................................................................................... 57

Appendix I Magnetic Ring Filter Instruction ....................................... 59

Appendix II Questions & Solutions ....................................................... 60

Appendix III Cable Diameter Calculation and Lightning &

Surge Protection...................................................................................... 61

CHAPTER I SYSTEM INTRODUCTION

1.1 Product Description

V6202-TA series HD 1MP and 2MP low light IP camera adopts 1/3"

progressive scan CMOS sensor. H.264 High profile/M-JPEG video

compression format allows image output resolution up to 1920×1080@30fps or

1280×720@30fps.

The camera supports three simultaneous video streams, bi-directional audio and

G.711 audio compression. Functioned with ICR day/night switch, motion

detection, privacy mask, alarm input/output and local recording, V6202-TA

series is bound to enhance security and convenience for your CCTV

surveillance system.

With convenient ABF function, V6202-TA series camera is easy to debug and

install.

V6202-TA series is widely used in financial institutions, telecommunications,

governments, schools, airports, factories, hotels, museums, city streets and

other high-resolution surveillance applications.

1.2 Product Features

Infinova’s V6202-TA series camera has the following features and functions:

 1/3" progressive scan CMOS sensor

 IR-Cut Removable (ICR) Filter for Day/Night switching

 Support Digital WDR function

 Onvif Profile S

 Sensitivity: 0.001 lux

 Auto Back Focus (ABF)

 High-resolution image signal output up to 1920×1080, with 1280×1024,

1280×960, 1280×720, 1024×768 and 800×600 optional (for V6202-TA2

series)

 High-resolution image signal output up to 1280×720, with 1024×768 and

800×600 optional (for V6202-TA0 series)

 Small bandwidth occupancy and high image quality

 High frame rate transmission: up to 30fps

 Three Simultaneous Video Streams: Dual H.264 & Scalable M-JPEG

 Smooth dynamic video replay

 Supports anti-reflection function

 Bi-directional audio, G.711

 Support storage with TF card

 Up to four definable motion detection areas

 Up to four definable privacy mask areas

 Local Recording

 2 alarm inputs, 1 relay output

 Support multiple ways to handle alarms, such as email sending, FTP upload

and relay output

 Support simultaneous multi-user access and parameter configuration via

Web Serve r

 Compatible with Infinova’s V2216, V2218 and other digital video

surveillance software

 Provide standard SDK, easily incorporated with digital surveillance systems

from a different supplier

 Supports public access

 With analog video debugging interface

 Supports wide voltage, ESD and surge protection

1.3 System Requirement

Configuration of the computer to display image and control the camera:

CPU: Intel Pentium 4 2.4 GHz or above

RAM: 512 MB or greater

Network Port: 100M Ethernet port

Operating System: Microsoft Windows 7, Microsoft Windows XP

IE browser version: Microsoft Internet Explorer 6.0 or above

1.4 Product Model

This manual is for the following models:

V6202-TA024 Megapixel IP fixed camera, 1.0MPx, Day/Night,

Auto back focus, H.264/M-JPEG, 12VDC/24VAC

V6202-TA020 Megapixel IP fixed camera, 1.0MPx, Day/Night,

Auto back focus, H.264/M-JPEG,

PoE/12VDC/24VAC

V6202-TA224 Megapixel IP fixed camera, 2.0MPx, Day/Night,

Auto back focus, H.264/M-JPEG, 12VDC/24VAC

V6202-TA220 Megapixel IP fixed camera, 2.0MPx, Day/Night,

Auto back focus, H.264/M-JPEG,

PoE/12VDC/24VAC

1.5 Specifications

Model V6202-TA series

Image Sensor 1/3" progressive scan CMOS

Dynamic Range 72.4dB

Lens Mount C/CS

Auto Back Focus Available

Auto Iris DC driven

Day/Night

Functionality ICR

Sensitivity

For V6202-TA2 series,

Color mode: 0.05 Lux @ F1.2 (30IRE, AGC ON);

B/W mode: 0.01 Lux @ F1.2 (30IRE, AGC ON)

For V6202-TA0 series,

Color mode: 0.01 Lux @ F1.2 (30IRE, AGC ON)；

B/W mode: 0.001 Lux @ F1.2 (30IRE, AGC ON)

Exposure Scene mode, Manual mode, Shutter priority mode

Shutter Auto/Manual (1/1s~1/13000s)

White Balance Auto/Manual/Incandescent light/Cool white fluorescent

light/Sun light/Cloudy/Natrium light

Gain Control Auto/Manual

Noise Reduction 3D

Video

Compression H.264 High profile/M-JPEG

Maximum

Resolution

1920×[email protected]4/M-JPEG (for V6202-TA2 series);

1280×[email protected]/M-JPEG (for V6202-TA0 series)

Optional

Resolution

Major stream: 1920×1080, 1280×1024, 1280×960,

1280×720, 1024×768, 800×600 (for V6202-TA2 series),

Major stream: 1280×720, 1024×768, 800×600 (for

V6202-TA0 series);

Minor stream: 720×576, 720×480, 640×480, 352×288,

352×240

Maximum Frame

Rate 30fps

Data Rate Variable bit rate;

Constant bit rate: 256Kbps~10000Kbps

Audio

Audio Compression: G.711-u;

1 input (Linear level, Resistance: 1000 Ohm),

1 output (Linear level, Resistance: 600 Ohm)

Motion Detection Up to 4 areas

Privacy Mask Up to 4 masks

Local Recording Available

TF Card Storage Available, up to 32G

Upgrade Online Available

Password

Protection Available

Network Port One RJ45 10/100M self-adaptive Ethernet port

Applicable

Protocols

IPv4, IPv6, TCP, UDP, IGMP, DHCP, FTP, SNMP (V3),

SMTP, NTP, RTP, RTSP, RTCP, HTTP, HTTPS, TSL, SSL,

802.1X, QoS, PPPoE, DNS, ARP, ICMP, UPNP, DDNS,

Profile S

Alarm 2 alarm inputs, 1 relay output

Power Supply PoE（IEEE 802.3af Class 2）/12VDC（10VDC~40VDC）

/24VAC

（

12VAC~40VAC

）

Power

Consumption

＜5W (when the camera is focusing, the power

consumption will be less than 8W.)

ESD protection ±6KV(all ports)

Surge protection ±6KV（network port）

Operating

Temperature 14°F~122°F (-10°C~+50°C)

Storage

Temperature -4°F~140°F (-20°C~+60°C)

Operating

Humidity 0%-90% RH (non-condensing)

Dimensions

(H×W×L) 2.84"×2.97"×5.47" (72mm×75.5mm×139mm)

Box Dimensions

(L×W×H) 8.07"×4.92"×3.94" (205mm×125mm×100mm)

Unit Weight 1.21lbs. (0.55kg)

Shipping Weight 1.54lbs. (0.70kg)

1.6 Notice

1. Firstly perform network settings after login. The gateway IP address should

be set as that of the connected to the network camera.

2. The IP address is not allowed to conflict with that of other devices; otherwise,

you cannot visit the camera.

3. If the purchased IP camera utilizes PoE power supply, please connect

equipments according to the parameter of the Power Supply Switcher strictly.

Furthermore, practical test of maximum network cable length for the Power

Supply Switcher must be performed, so as to avoid the camera failure caused

by insufficient power supply of the Power Supply Switcher, or to avoid the

destruction of Switcher.

CHAPTER II INSTALLATION AND PORT INTRODUCTION

2.1 Installation Precautions

 Do not drop the camera or subject it to strong knock.

 Do not point the camera lens toward the sun or other strong light.

 Do not install the camera in environment with temperature beyond the

acceptable range (from -10°C to 50°C), or with high humidity, direct

rainfall, frequent vibrations and shocks.

 Add with auxiliary illumination device in case of low illumination to avoid

poor image quality.

2.2 Back Panel and Control Parts

Figure 2-1 Back View

①Alarm Input/Output, Audio Input/Output, RS-485 Terminal

②Network Port (used for PoE power supply)

③Analog Video Output ④TF Card Slot

⑤Network LED Indicator ⑥Back Focus Adjusting

⑦Reset ⑧Status LED Indicator

⑨Arrester ground terminal ⑩Power Input Terminal

Notes: The analog video is closed when the MJPEG video stream is enabled.

To enable the analog video, please close the MJPEG video stream.

On the left of camera body (face the lens to view), there is an IRIS connector.

The pin definition is as follows:

Note: The camera supports DC DRIVE. The default setting is DC DRIVE.

Figure 2-2

 ⑦Reset button: The camera supports short press and extended press reset

modes. If press and hold the button from 2s to 15s (i.e. short press), Power

LED Indicator will turn green, and camera’s parameters will restore the

default values. If press and hold the button more than 15s (i.e. extended

press), Power LED Indicator will turn orange, and camera’s system will

resume factory default settings. Power LED Indicator will flicker quickly

while holding time is about 15s. Note: if press “Reset” button, the IP address

will become to 192.168.1.100.

 ⑥Back Focus Adjusting button: Mount lens to the camera and install the

unit to the desirable place, then power on. Next, modulate the knobs on the

Pin DC DRIVE

1DAMP-

2DAMP+

3DRIVE+

4DRIVE-

lens to zoom and focus. If you cannot get clear image in this way, press ⑥

Back Focus Adjusting button to adjust focus automatically.

2.3 Dimensions

(Unit: inch, in the parentheses is mm)

2.97(75.5)

NETWORK CAMERA

5.47(139.0)

2.84(72.0)

Figure 2-3

2.4 Installation of Camera

When mounting the camera on fixer, pan/tilt, etc., use 1/4-20UNC screw and

the camera-mounting screw hole located on the camera-mounting bracket. The

camera-mounting bracket can be mounted on the top or at the bottom of the

camera. See the figure below:

Camera-mounting screw holes

Camera-mounting bracket fixing screw

holes (4 pcs)

Camera-mounting bracket

Figure 2-4 Camera-mounting Bracket

Note:

 When installing the unit on a bracket, make sure to choose the suitable

position that can support the weight of the camera and the bracket in years

and fix them properly.

 Exercise maximum caution when installing the unit to the wall or ceiling.

You should not engage in the installation work yourself. Ask a professional

to do the job, since the fall of the unit can result in injuries and accidents.

 When installing the unit on a fixer, turn table, etc., make sure to install it

firmly using a mounting hole provided on the mounting bracket to prevent

fall.

 As a failsafe against falling, attach the unit by chain, wire cable or other

safety restraint to an appropriate anchor point.

CHAPTER III IE BROWSER SETTINGS

When view the video, the user need to adjust the IE browser of the monitor or

other video devices, and set proper system function based on the following

instructions:

 Support IE browser version: Internet Explorer 6.0 or above;

 Must install InfiPlayerAX control and equip with Directx 9.0c.

3.1 Equipment Connection

V6202-TA series IP camera can be directly connected to a computer, or

connected to a network.

Note: Check whether the connection is tight or not before power-on.

3.2 Software Installation

The installation procedures of V6202-TA series camera image software are

listed as follows:

(1) Login

First, start IE browser and enter IP address. Enter user name and password in

the pop-up login interface.

The default IP address is http://192.168.1.100; the default subnet mask is

255.255.255.0 and the default gateway IP address is 192.168.1.254. For normal

access, correctly set local IP parameters before system login.

Do log in the system with the default super user for the first time to run the

software. The default Super User is admin (password: admin).

(2) Install and run Control

There are two ways to install control.

Method 1:

The prompt message as below will come out in live view window after a

successful login. Click the link to run, or store the exe file, then run it.

Figure 3-1

If the installation fails, check whether there is video viewed through other IE

window or page. You should close the video or the IE window directly.

If it successes, click refresh, you can view the live video.

Method 2:

The prompt message as below will come out in the page after a successful

Figure 3-2

Then the prompt of security warning will pop up to remind the user to install

InfiPlayerAX control. Click “Install”.

Figure 3-3

After InfiPlayerAX control is installed, you can view the live video. If it pops

up reboot prompt, please cancel reboot. Then close all the IE window and

install InfiPlayerAX control once again. The live video will display as below:

Figure 3-4

Note:

If InfiPlayerAX control installation falls, the live video won’t display. Then,

you should change the IE security level.

1. Select “Tool” in the menu bar, and then select “Internet Options” from the

drop-down menu.

2. Select “Security” in the pop-up Internet options.

3. Click “Internet” icon and then click “Custom Level”.

4. Select “Enable” or “Prompt” in the options of “Download unsigned ActiveX

controls”.

5. Click Privacy in the “Internet”, clear “Block pop-ups”, then redraw the screen

and install control as per the prompt. The live video will display.

By now, the IE browser setting for image viewing comes to an end.

CHAPTER IV BASIC FUNCTION OPERATION

This chapter mainly introduces the settings and operation of V6202-TA series.

4.1 Live View

Start IE browser after the server is powered on for about 75 seconds, and then

enter IP address, such as http://192.168.1.100 (default), in the address field.

Note: The default subnet mask is 255.255.255.0 and the default gateway IP

address is 192.168.1.254. For normal access, please correctly set local IP

parameters before system login.

The login interface is displayed as shown in figure below in English operating

system.

Figure 4-1 User Login

Do log in the system with the default super user for the first time to run the

software. The system default Super User is admin (password: admin). Input the

correct user ID and password and then press “OK” button to login the system.

After login is successful, the following interface will display:

Figure 4-2 Live View

V6202-TA series IP camera supports H.264 and M-JPEG video compression

formats. After successful login, it enters H.264 major stream live video

interface. Users can also select H.264 minor stream or MJPEG from the

dropdown list of stream type. In the H.264 major or minor stream type, users

can do recording, snap shooting, and audio in/out settings. Over browsing

videos, users can also select a proper video scale.

Play mode: live or fluid for option.

Click the button to snapshoot and to enter the storage path. Default:

C:\InfiPlayerAX\Picture.

V6202-TA series supports local recording. Click the recording button to

start recording; when the button changes to , click it to stop recording.

During local recording, “REC”appears on the video screen. Click the

button to enter the recording storage path. Default: C:\InfiPlayerAX\

Video.

Users can set the snap shooting and recording storage path in the audio and

video settings interface.

Indicate audio input/output disabled. Click the buttons to enable audio

input/output and then the buttons will be shown as .

Indicate that the motion detection and privacy mask functions are

disabled. Click the buttons to enable them and then the buttons will be shown

as .

Note: only when motion detection or privacy mask is enabled, you can set the

corresponding function in Audio & Video Settings, refer to Section 4.5.3 or

4.5.4 for details.

PTZ control and PTZ function: When the camera is working with Pan/Tilt, it

is able to control the PTZ to perform such operations, such as direction

control, focus and zoom adjustment, and speed setting; Also, with PTZ

Function, wiper, defogger, presets, patterns, auto-pan and home return can be

called up.

Note: the login web page language should be set to the same as that of PC's

operating system.

Click the option tab “Settings” to enter the system setting interface.

Figure 4-3 Settings Interface

With the help of navigation menu on the left, Super user can perform the

following operations: Basic Information View, Time Settings and Advanced

Settings, Network Settings, Camera Settings (including Basic Set, Exposure,

Effect Set, White Balance, Focus, Reset), Audio & Video Settings, Alarm

Settings, Record setting, Account Settings (Add/Delete User, Change

Password), Log, etc.

Note: The following instructions are used for the super user.

4.2 System

Click the navigation bar [System] and it displays the following three option tabs:

System, Time and Advanced, as shown in Figure 4-3.

4.2.1 System Information

The initial interface of System Settings displays related system information,

such as basic system information, network settings, NTP settings, alarm settings,

H.264/MJPEG video settings, etc.

4.2.2 Time Settings

Figure 4-4 “Time” Settings

Time Zone Settings

Time Zone: Select the desired time zone in the scroll box, and then click “Save”

to save it.

There are 33 time zones for your selection.

If Daylight Saving Time is applied in your region, please turn on Daylight

saving time.

After settings completed, please click the button “Save”.

NTP Settings

Set the NTP server’s IP address, test NTP server’s status, and set parameters of

Sync with NTP, including enable/disable Sync with NTP, Sync time and Sync

interval.

After completed, please click the button “Save”.

Sync Now

There are two sync modes: local sync and NTP sync.

Local Sync means the system time is consistent with that of local PC. In the

NTP Sync mode, the system will automatically adjust time to the same as that

of NTP Server.

4.2.3 Advanced Settings

Figure 4-5 “Advanced” Settings

Software Update

Free software update is provided for V6202-TA series camera, and this update

service can reduce system maintenance budget.

Confirm the requirement submitted by user, we will provide the latest software

for download, and help user to update the V6202-TA series camera.

Follow the steps below to update software:

Click “Browse” button on the interface and the file selection dialog box will

pop up.

Figure 4-6

Select update file, and press “Open” button. The selected update file will be

displayed in the Software Update box.

After that, click “Submit” button to update software, the following information

will appear:

Figure 4-7

Click “Yes” button, run the program to finish the update.

The response time is due to the program type. You may wait a long time for

some program. Do not power off during the update process. Power-off will

make update fail, even damage the original program or unable to update again.

After update successfully, it needs to reboot the system. There is time prompt in

the web page during reboot. After reboot, it will skip to new web page to run

new program.

Note: Available only for the super user.

Factory Settings

V6202-TA series camera provides online reset function, which greatly

facilitates reset adjustment.

Select “Keep current IP unchanged”, click “Reset” button and the system will

pop up a message as below:

Figure 4-8

Click “OK”, all the parameters (excluding IP address) will be reset to the

factory default settings.

If “Keep current IP unchanged” is unselected, the IP address will be reset to the

factory default settings.

There is time prompt in the web page during reset. After reset, it will skip to

new web page.

If current IP unchanged, you can access web page directly. If IP address resets

to 192.168.1.100, you can’t access web page. Then, you have to set PC’s IP

address to 192.168.1 section, such as 192.168.1.25. After that, access web page

to change camera’s IP address and save, PC’s IP address will restore to the

corresponding section.

Note:

1. To avoid error happens, the operation of online reset function should be

performed under qualified personnel’s guide.

2. Default IP address is 192.168.1.100, and default subnet mask is

255.255.255.0.

3. Do not power off during reset, or else the reset will fail.

Online Reboot

Click “Reboot” button, the dialog box “This operation will take 75 seconds,

are you sure to continue？”pop up. Click “OK” and the system will restart.

There is time prompt in the web page during reboot. After reboot, it will skip to

new web page.

Note: Available only for the super user.

4.3 Network Settings

Click “Network” in the navigation bar, and the following interface will display:

Figure 4-9 Network Settings

11 options tabs are available: Network, FTP, SMTP, HTTPS, 802.1X, QOS,

IGMP, SIP, MDA, DDNS and UPnP.

4.3.1 Network Settings

IP mode: support both IPv4 and IPv6 modes. Network parameters are slightly

different under different IP modes.

Figure 4-10 Network Settings

Under IPv4 mode, users can enable or disable DHCP. When it is disabled, users

can set Unit IP address, Subnet mask, Gateway and DNS server IP address

manually.

Notes: The system indicator quickly flickers for 5s after the network settings

completed.

Users can also enable/disable PPPoE in this interface. If enabled, users can set

the user name and password.

V6202-TA series camera supports heartbeat function. In SNMP settings, set and

save the heartbeat sever IP address and Heartbeat interval, and then the

heartbeat package will be sent to the server or client, which greatly facilitates

the server or client to know about the camera’s network status.

4.3.2 FTP Settings

Figure 4-11 FTP Settings

V6202-TA series camera has the function of alarm associated with FTP upload

(alarm triggered image snapshot). Configure server IP, user name and password

in the FTP settings and activate FTP handling way in alarm settings, then alarm

triggered images FTP upload can be achieved.

4.3.3 SMTP Settings

Figure 4-12 SMTP Settings

User needs to set mail server, recipient, etc in SMTP settings interface.

 Server IP: Set mail server address.

 From: Set sender’s mail address.

 To: Mail address of recipient.

 CC: Mail address of the person copy to.

 Authentication: Enable or disable authentication function. This function

should be set according to authentication requirements of mail server.

 User name: Sender’s name, it can be set according to user’s needs.

 Password: Set sender’s password.

After setting, click “Save” to take effect.

If user selects “mail” in “Alarm Settings” interface, system will send mails

according to SMTP settings.

4.3.4 HTTPS Settings

Figure 4-13 HTTPS Settings

V6202-TA series camera supports HTTPS protocol. You can import the CA

certificate in the interface.

4.3.5 802.1X Settings

Figure 4-14 802.1X Settings

V6202-TA series camera supports 802.1X protocol. You have to enable 802.1X

authentication when needed. Then, select an EAP method and enter the user

name and password.

4.3.6 QOS Settings

Figure 4-15 QOS Settings

There are 4 network Qos modes to be selected:

(1) Normal Service

(2) Max Reliability

(3) Max Throughput

(4) Min Delay

Recommend: Normal Service.

4.3.7 IGMP Settings

Figure 4-16 IGMP Settings

V6202-TA series camera supports multicast function. In the IGMP interface,

users can select the stream type and set the state, multicast IP address and RTP

port.

4.3.8 SIP Settings

Figure 4-17 SIP Settings

SIP Server: to configure SIP server for device;

SIP Server IP: the IP address of SIP server;

Port: the port number of SIP server;

Server ID: the ID of SIP server;

Device ID: the device ID used for registration with SIP server;

Alarm ID: the ID registered for device alarm;

Heat Beat Interval: the interval to send heartbeat information by the device in

seconds;

After configuration completed, click “Save” and the device sends a registration

request to the server.

Position Information: the mounting information or instruction for device.

Longitude: the longitude of mounting position, as precise to two places of

decimal;

Latitude: the latitude of mounting position, as precise to two places of decimal.

4.3.9 MDA Settings

Figure 4-18 MDA Settings

In MDA settings interface, you can set the Sever which the motion detection

alarm uploads to.

State: disable or enable motion detection alarm upload. When it’s on, you can

set camera name, user name, password, server IP and Port number. After setting

completed, click “Save” button to take effect.

4.3.10 DDNS Settings

Figure 4-19 DDNS Settings

Dynamic Domain Name System (DDNS) synchronizes the host name and

dynamic IP address continuously. Users don’t have to memorize the dynamic

IP address, but enter the dynamic domain name to connect the IP camera.

DDNS needs a PC with fixed IP address on the Internet to run the dynamic

domain name server.

Operation: select DDNS type in Enable option, enter the IP address of the

DDNS server into the address bar, configure domain name, user name, and

password and update time and then save the settings. Open the IE browser, and

enter the domain name to go to the query page of the device.

4.3.11 UPnP Settings

Create mapping between private network and the Internet via UPNP protocol.

Select UpnP option and enter the configuration page. The added mapping list

appears on the page.

Figure 4-20 UPnP Settings

In “Operation” column, means to delete; means to edit user

information.

Click Add button to add the mapping.

Figure 4-21

4.4 Camera Settings

Click “Camera” in the navigation bar to enter the interface shown as below:

Figure 4-22 Basic Settings

4.4.1 Basic Settings

You can set the following parameters:

Flicker frequency: 50Hz or 60Hz.

CVBS: It automatically changes with the flicker frequency. (Notes: analog

videos are shut off after MJPEG stream is enabled. To enable analog videos,

please disable MJPEG stream.)

Enable or disable backlight compensation or WDR.

Contrast Enhance: 1~6 levels match with 6 kinds of Gamma curve separately. If

it is set to Auto, the system will adjust automatically.

4.4.2 Exposure Settings

Figure 4-23 Exposure Settings

Exposure set, auto aperture, ICR control, ICR switch time, scene, AGC, shutter

speed and manual AGC can also be set in this interface.

Exposure Set: Manual, Scene and Shutter priority. In the Scene mode, indoor or

outdoor can be selected and AGC can be set (maximum 64X); if set to manual

mode, shutter speed can be set from 1/25s to 1/8000s and manual AGC can be

set to 1X to 64X, yet the scene and AGC are nonadjustable; if set to shutter

priority mode, the shutter speed and AGC can be set.

Auto Aperture: to enable or disable auto iris.

ICR Control: Auto mode, Night or Day. In Auto mode, the camera can

automatically control the day/night switching; in Day mode, videos are in color

mode; in Night mode, videos are in black/white mode.

AE target: set AE target level. It can adjust video brightness via AE target setup.

4.4.3 Effect Settings

In the Effect Settings interface, users can adjust the brightness, sharpness, hue,

contrast, saturation and 3D denoise in two ways: General or Mode, as shown in

the figure below:

Figure 4-24 Effect Set - General

Drag the sliding block to adjust the brightness, sharpness, hue, contrast,

saturation and 3D denoise.

Figure 4-25 Effect Set - Mode

The camera supports 6 video effect modes. Users can set and save Name, ICR

control mode and Scene parameters for each mode. Click “Factoryset” to

restore it to default settings.

The camera provides 7 Scene modes: Normal, Anti Fog, Motion, Entrance,

Natrium, Sharpen, USrMode. Each mode matches with a group of parameters, such

as brightness, sharpness, hue, contrast, saturation and 3D denoise.

In the Mode call, users can set effect mode call status and call period.

4.4.4 White Balance Settings

Figure 4-26 White Balance Settings

The camera has rich white balance modes, including Auto, Manual,

Incandescent light, Cool white fluorescent light, Sun light, Cloudy and Natrium

light. If set to manual mode, you can set the red gain and blue gain.

Table of contents

Other Infinova IP Camera manuals

Infinova

Infinova V6202IR-H02 Series User manual

Infinova

Infinova V6202-T00 Series User manual

Infinova

Infinova V5422IR-A8065ST-W User manual

Infinova

Infinova V6812-T00 Series User manual

Infinova

Infinova V1700N-NE2 Series User manual

Infinova

Infinova V6812IR-H0 Series User manual

Infinova

Infinova V5112IR-A8 series User manual

Infinova

Infinova V6202-T03 Series User manual

Infinova

Infinova V1492N-18N05 User manual

Infinova

Infinova V1700N-NE2 Series User manual

Popular IP Camera manuals by other brands

FLIR

FLIR Exx series user manual

Avigilon

Avigilon H4A-BO1-IR installation guide

Digital Watchdog

Digital Watchdog DWCA-C128-64 manual

ShareTech

ShareTech AV1 user manual

Ezviz

Ezviz C6C quick start guide

Melchioni

Melchioni UCAM 2015 manual

Geutebruck

Geutebruck G-Cam/ESD-4630 quick guide

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG installation manual

Mitel

Mitel 6800i Series Administrator's guide

Vitek

Vitek VTC-IR403-212NP quick start guide

THOMSON

THOMSON DSC - 323W user guide

AVer

AVer FB2027 user manual

ENFORCER

ENFORCER EV-T5105-N2SQ manual

Wansview

Wansview NC543 user manual

Eneo

Eneo MCB-64A0003M0A Quick installation guide

deView electronics

deView electronics CBDNI36F instruction manual

Swann

Swann SwannEye user manual

LevelOne

LevelOne IP CamSecure user manual