IFM SD26 Series User manual

Operating instructions
Flow meter compressed air / gases
SD25xx
SD26xx
SD55xx
SD56xx
SD65xx
SD66xx
SD85xx
SD86xx
SD95xx
80280071 / 00 01 / 2019
UK

2
Contents
1 Preliminary note���������������������������������������������������������������������������������������������������5
1�1 Symbols used ������������������������������������������������������������������������������������������������5
1�2 Warnings used�����������������������������������������������������������������������������������������������5
2 Safety instructions �����������������������������������������������������������������������������������������������6
3 Functions and features ����������������������������������������������������������������������������������������7
3�1 Pressure Equipment Directive (PED) ������������������������������������������������������������7
3�2 Applications ���������������������������������������������������������������������������������������������������7
4 Function���������������������������������������������������������������������������������������������������������������8
4�1 Processing of the measured signals��������������������������������������������������������������8
4�2 Switching output ��������������������������������������������������������������������������������������������9
4�3 Analogue output�������������������������������������������������������������������������������������������10
4�4 Consumed quantity monitoring [ImP] ����������������������������������������������������������12
4�4�1 Meter reading �������������������������������������������������������������������������������������12
4�4�2 Counter reset ������������������������������������������������������������������������������������12
4�4�3 Consumed quantity monitoring via pulse signals �������������������������������13
4�4�4 Consumed quantity monitoring via preset counter �����������������������������13
4�5 Measured value damping ����������������������������������������������������������������������������14
4�6 Low flow cut-off �������������������������������������������������������������������������������������������14
4�7 Simulation����������������������������������������������������������������������������������������������������14
4�8 Colour of the characters in the display ��������������������������������������������������������15
4�9 IO-Link ���������������������������������������������������������������������������������������������������������16
4�9�1 Additional functions via IO-Link ����������������������������������������������������������16
5 Installation����������������������������������������������������������������������������������������������������������16
5�1 Installation location ��������������������������������������������������������������������������������������17
5�2 Installation position ��������������������������������������������������������������������������������������17
5�2�1 Inlet and outlet pipe lengths����������������������������������������������������������������17
5�2�2 Orientation �����������������������������������������������������������������������������������������18
5�3 Installation in pipes ��������������������������������������������������������������������������������������18
6 Electrical connection������������������������������������������������������������������������������������������19
7 Operating and display elements ������������������������������������������������������������������������21
8 Menu������������������������������������������������������������������������������������������������������������������22
8�1 Process value display (RUN)�����������������������������������������������������������������������22
8�2 Main menu���������������������������������������������������������������������������������������������������23

3
UK
8�3 Extended functions (EF) ������������������������������������������������������������������������������24
8�4 Submenu OUT1�������������������������������������������������������������������������������������������25
8�5 Submenu OUT2�������������������������������������������������������������������������������������������27
8�6 Submenu CFG���������������������������������������������������������������������������������������������29
8�7 Submenus MEM, DIS ����������������������������������������������������������������������������������31
8�8 Submenus COLR, SIM ��������������������������������������������������������������������������������33
9 Set-up ����������������������������������������������������������������������������������������������������������������35
10 Parameter setting ��������������������������������������������������������������������������������������������35
10�1 Parameter setting in general ���������������������������������������������������������������������36
10�1�1 Select submenu��������������������������������������������������������������������������������36
10�1�2 Change to the process value display (RUN mode) ��������������������������36
10�1�3 Lock / unlock�������������������������������������������������������������������������������������36
10�1�4 Timeout���������������������������������������������������������������������������������������������37
10�2 Settings for volumetric flow monitoring������������������������������������������������������37
10�2�1 Limit monitoring OUT1 or OUT2 / hysteresis function ����������������������37
10�2�2 Limit monitoring OUT1 or OUT2 / window function ��������������������������37
10�2�3 Analogue signal volumetric flow OUT2���������������������������������������������37
10�3 Settings for consumed quantity monitoring �����������������������������������������������38
10�3�1 Quantity monitoring by pulse signal OUT1 or OUT2 ������������������������38
10�3�2 Quantity monitoring by preset counter OUT1 or OUT2 ��������������������38
10�3�3 Manual counter reset������������������������������������������������������������������������38
10�3�4 Time-controlled counter reset �����������������������������������������������������������38
10�3�5 Deactivation of the counter reset������������������������������������������������������38
10�3�6 Counter reset using an external signal ���������������������������������������������39
10�4 Settings for temperature monitoring ����������������������������������������������������������39
10�4�1 Limit monitoring OUT1 or OUT2 / hysteresis function ����������������������39
10�4�2 Limit monitoring OUT1 or OUT2 / window function ��������������������������39
10�4�3 Analogue signal temperature OUT2 �������������������������������������������������39
10�5 Settings for pressure monitoring����������������������������������������������������������������40
10�5�1 Limit monitoring OUT1 or OUT2 / hysteresis function ����������������������40
10�5�2 Limit monitoring OUT1 or OUT2 / window function ��������������������������40
10�5�3 Analogue signal pressure OUT2�������������������������������������������������������40
10�6 User settings (optional)������������������������������������������������������������������������������41
10�6�1 Standard display�������������������������������������������������������������������������������41
10�6�2 Standard unit of measurement for volumetric flow ���������������������������41
10�6�3 Standard unit of measurement for temperature��������������������������������41

4
10�6�4 Standard unit of measurement for pressure �������������������������������������41
10�6�5 Measured value damping �����������������������������������������������������������������42
10�6�6 Output logic ��������������������������������������������������������������������������������������42
10�6�7 Medium for SDx6xx units������������������������������������������������������������������42
10�6�8 Low flow cut-off���������������������������������������������������������������������������������42
10�6�9 Standard conditions��������������������������������������������������������������������������42
10�6�10 Zero-point calibration pressure�������������������������������������������������������42
10�6�11 Colour of the characters in the display �������������������������������������������43
10�6�12 Switch-on /switch-off delay �������������������������������������������������������������43
10�6�13 Error behaviour of the outputs ��������������������������������������������������������44
10�6�14 Restore factory setting��������������������������������������������������������������������44
10�7 Diagnostic functions ����������������������������������������������������������������������������������45
10�7�1 Read min/max values �����������������������������������������������������������������������45
10�7�2 Simulation�����������������������������������������������������������������������������������������45
11 Operation ���������������������������������������������������������������������������������������������������������46
12 Error correction������������������������������������������������������������������������������������������������46
13 Maintenance, repair and disposal��������������������������������������������������������������������48
14 Factory setting �������������������������������������������������������������������������������������������������49

5
UK
1 Preliminary note
Detailed instructions, technical data, approvals and other information via
the QR code on the unit / on the packaging or at www�ifm�com�
1.1 Symbols used
Instructions
> Reaction, result
[…] Designation of keys, buttons or indications
Cross-reference
Important note
Non-compliance may result in malfunction or interference�
Information
Supplementary note�
1.2 Warnings used
CAUTION!
Warning of personal injury�
Slight reversible injuries may result�

6
2 Safety instructions
• The device described is a subcomponent for integration into a system�
- The manufacturer is responsible for the safety of the system�
- The system manufacturer undertakes to perform a risk assessment and to
create a documentation in accordance with legal and normative requirements
to be provided to the operator and user of the system� This documentation
must contain all necessary information and safety instructions for the operator,
the user and, if applicable, for any service personnel authorised by the manu-
facturer of the system�
• Read this document before setting up the product and keep it during the entire
service life�
• The product must be suitable for the corresponding applications and environ-
mental conditions without any restrictions�
•
•
• If the operating instructions or the technical data are not adhered to, personal
injury and/or damage to property may occur�
• The manufacturer assumes no liability or warranty for any consequences
caused by tampering with the product or incorrect use by the operator�
• Installation, electrical connection, set-up, operation and maintenance of the unit
must be carried out by qualified personnel authorised by the machine operator�
• Protect units and cables against damage�

7
UK
3 Functions and features
The unit monitors the standard volume flow of compressed air in industrial use
and / or technical gases �
It detects the 5 process variables flow velocity, volumetric flow quantity, consumed
quantity, medium temperature and pressure�
All indications apply to standard volume flow to DIN ISO 2533, i�e� volume flow
at 1013 mbar, 15 °C and 0 % relative air humidity� The unit can be set to different
standard conditions �
This is a class A product� This product may cause radio interference in
domestic areas�
If required, take appropriate EMC screening measures�
3.1 Pressure Equipment Directive (PED)
The units comply with the Pressure Equipment Directive� They are designed for
stable gases of group 2 fluids and manufactured in accordance with sound engi-
neering practice�
3.2 Applications
SDx5xx
• Compressed air
SDx6xx
• Compressed air
• Argon (Ar)
• Carbon dioxide (CO2)
• Nitrogen (N2)
Selection of the medium to be monitored �

8
4 Function
• The volumetric flow is monitored by a calorimetric measuring system, the
measured signals are evaluated by the electronics�
• The unit detects the pressure and the media temperature of the volumetric flow
as additional process values�
• The unit features an IO-Link interface
• The unit displays the current process values�
• The unit has many self-diagnostic options�
• A simulation mode allows simplified set-up of the sensor�
4.1 Processing of the measured signals
The unit generates 2 output signals according to the parameter setting:
OUT1: 7 selection options
- switching signal for volumetric flow quantity limit
- switching signal for temperature limit
- switching signal for pressure limit
- switching signal for preset counter
- pulse signal for quantity meter
- IO-Link
- OFF (output switched to high impedance)
OUT2: 10 selection options
- switching signal for volumetric flow quantity limit
- switching signal for temperature limit
- switching signal for pressure limit
- switching signal for preset counter
- switching signal for quantity meter
- analogue signal for volumetric flow quantity
- analogue signal for temperature
- analogue signal for pressure
- input for external counter reset signal (InD)
- OFF (output switched to high impedance)

9
UK
4.2 Switching output
OUTx changes its switching status if it is above or below the set switching limits
(flow, temperature or pressure)� Hysteresis or window function can be selected�
Example of volumetric flow monitoring:
Hysteresis function Window function
SP
rP FL
FH
SP = set point
rP = reset point
HY = hysteresis
Hno / Fno = NO (normally open)
FH = upper limit
FL = lower limit
FE = window
Hnc / Fnc = NC (normally closed)
When the hysteresis function is set, the set point (SP) is defined first and
then the reset point (rP) which must have a lower value� If only the set point
is changed, the reset point is changed automatically; the difference remains
constant�
When set to the window function, the upper limit value (FH) and the lower
limit value (FL) have a fixed hysteresis of 0�25 % of the final value of the
measuring range� This keeps the switching status of the output stable if the
volumetric flow varies slightly�

10
4.3 Analogue output
The unit provides an analogue signal that is proportional to the volumetric flow
quantity, the medium temperature or the pressure�
Within the measuring range the analogue signal is 4���20 mA�
The measuring range is scalable:
• [ASP2] determines at which measured value the output signal is 4 mA�
• [AEP2] determines at which measured value the output signal is 20 mA�
Minimum distance between [ASP2] and [AEP2] = 20 % of the final value of
the measuring range�
If the measured value is outside the measuring range or in the event of an internal
error, the current signal indicated in Fig� 1 is provided�
For measured values outside the display range or in case of a fault, messages are
displayed (cr�UL, UL, OL, cr�OL, Err; )�
The analogue signal in case of a fault is adjustable :
• [FOU] = On determines that the analogue signal goes to the upper final value
(21�5 mA) in case of an error�
• [FOU] = OFF determines that the analogue signal goes to the lower final value
(3�5 mA) in case of an error�
• [FOU] = OU defines that in case of a fault the analogue signal reacts as defined
by the current parameters�
This manual suits for next models
8
Table of contents
Other IFM Measuring Instrument manuals









































