Hantek DSO3102 User manual
PC Based Digital Oscilloscope
USER MANUAL
DSO3102 DSO3102A
DSO3202 DSO3202A
www.hantek.com
Content
General Safety Summary.............................................................................. 1
Chapter 1 Getting Start ................................................................................. 2
1.1 System Requirement............................................................................................ 3
1.2 Install Software..................................................................................................... 4
1.3 Install Driver ......................................................................................................... 7
1.4 General Features ............................................................................................... 10
1.5 General Check ................................................................................................... 11
1.6 Function Check .................................................................................................. 12
1.7 Self Calibration................................................................................................... 13
1.8 Accessories........................................................................................................ 13
Chapter 2 Operating Basics ....................................................................... 14
2.1 The User’s Interface........................................................................................... 15
2.2 The Menu System .............................................................................................. 17
2.3 The Vertical System ........................................................................................... 19
2.4 The Horizontal System....................................................................................... 20
2.5 The Trigger System............................................................................................ 21
2.6 Input Connector.................................................................................................. 22
Chapter 3 Oscilloscope Functions ............................................................ 23
3.1 Setup the Oscilloscope ...................................................................................... 24
3.2 Set Vertical System ............................................................................................ 25
3.3 Setup Horizontal System.................................................................................... 31
3.4 Set Trigger System............................................................................................. 32
3.5 Save/Load.......................................................................................................... 37
3.6 Utility Function.................................................................................................... 38
3.7 Measure Signal .................................................................................................. 42
3.8 The Display System ........................................................................................... 48
3.9 Zoom In/Out and Drag Waveforms .................................................................... 53
3.10 Interpolation ..................................................................................................... 55
3.11 Acquisition Modes ............................................................................................ 57
3.12 Print And Print Preview .................................................................................... 57
Chapter 4 Application Example.................................................................. 59
4.1 Simple Measurement ......................................................................................... 60
4.2 Capturing a Single-Shot Signal .......................................................................... 61
4.3 The Application of the X-Y Operation ................................................................. 61
4.5 Taking Cursor Measurements ............................................................................ 63
Chapter 5 Appendix .................................................................................... 66
Appendix A: Specifications ....................................................................................... 67
Appendix B: Accessories.......................................................................................... 68
Appendix C: General Maintenance .......................................................................... 69
General Safety Summary
General Safety Summary
Review the following safety precautions carefully before operate the device to avoid any personal
injuries or damages to the device and any products connected to it.
To avoid potential hazards use the device as specified by this user’s guide only.
To Avoid Fire or Personal Injury
Use Proper Power Cord. Use only the power cord specified for this product and certified for the
country of use.
Connect and Disconnect Properly. Do not connect or disconnect probes or test leads while
they are connected to a voltage source.
Connect and Disconnect Properly. Connect the probe output to the measurement device
before connecting the probe to the circuit under test. Disconnect the probe input and the probe
reference lead from the circuit under test before disconnecting the probe from the measurement
device.
Observe All Terminal Ratings. To avoid fire or shock hazard, observe all ratings and markings
on the product. Consult the product manual for further ratings information before making
connections to the product.
Use Proper Probe. To avoid shock hazard, use a properly rated probe for your measurement.
Avoid Circuit or Wire Exposure. Do not touch exposed connections and components when
power is on.
Do Not Operate With Suspected Failures. If suspected damage occurs with the device, have it
inspected by qualified service personnel before further operations.
Provide Proper Ventilation. Refer to the installation instructions for proper ventilation of the
device.
Do not operate in Wet/Damp Conditions.
Do not operate in an Explosive Atmosphere.
Keep Product Surfaces Clean and Dry.
USER’S MANUAL 1
Getting Start
Chapter 1 Getting Start
The oscilloscope is small, lightweight, no external power required, portable oscilloscopes! The
oscilloscopes is ideal for production test, research and design and all of the applications involving
analog circuits test and troubleshooting, as well as education and training.
In addition to the list of general features on the next page, this chapter describes how to do the
following tasks:
System Requirements
Install software
Install Driver
General Features
General Check
Probe Compensation
Function Check
Self Calibration
Accessories
USER’S MANUAL 2
Getting Start
1.1 System Requirement
To run the oscilloscope software, the needs of computer configuration are as follows:
Minimum System Requirements
Operating System
Window XP/Vista/Win 7/Win 8
Processor
Upwards of 1.00G processor
Memory
256M byte
Disk Space
500M disk free space
Screen resolution
800 x 600
Recommended Configuration
Operating System
Windows XP SP3 System
Processor
2.4G Processor
Memory
1G Byte Memory
Disk Space
80G Disk Space
Screen resolution
1024 x 768 or 1280 x 1024 resolution
DPI Setting
Normal Size (96DPI)
USER’S MANUAL 3
Getting Start
1.2 Install Software
Caution: You must install the software before using the oscilloscope.
1. While in Windows, insert the installation CD into the CD-ROM drive.
2. The installation should start up automatically. Otherwise in Windows Explorer, switch to the
CD-ROM drive and run Setup.exe.
3. The software Installation is started. Click 'Next' to continue.
USER’S MANUAL 4
Getting Start
4. Choose a destination directory. Click 'Next' to continue.
5. Check the setup information. Click Next to start copying of files.
USER’S MANUAL 5
Getting Start
6. This Status dialog is displayed during copying of files.
7. Updating Your System Configuration.
8. The installation is complete.
USER’S MANUAL 6
Getting Start
1.3 Install Driver
1.Connect the A-Type Plug of USB cable to your PC’S USB port.
2.Connect the other A -Type Plug of USB cable to the device’s USB port.
3.New hardware is found.
4.New hardware search wizard starts.
USER’S MANUAL 7
Getting Start
5.Select the specific location.
6.New hardware search wizard starts to search the driver.
USER’S MANUAL 8
This manual suits for next models
3
Table of contents
Other Hantek Measuring Instrument manuals
Hantek
Hantek HT8000 Series User manual
Hantek
Hantek 1832C User manual
Hantek
Hantek CC-650 User manual
Hantek
Hantek HTM200 Series User manual
Hantek
Hantek HDG1000A User manual
Hantek
Hantek 4032L User manual
Hantek
Hantek HT300B User manual
Hantek
Hantek Hantek2000 Series User manual
Hantek
Hantek DSO8000 Series User manual
Hantek
Hantek CC-800 User manual
