Hantek DSO3062L User manual
USER’S MANUAL
DSO3062L/DSO3062AL
http://www.hantek.com
Content
General Safety Summary ..............................................................................1
Chapter 1 Getting Start..................................................................................2
1.1 System Requirement ........................................................................................... 3
1.2 Install Software..................................................................................................... 4
1.3 Install Driver ......................................................................................................... 7
1.4 General Features ............................................................................................... 10
1.5 General Check ....................................................................................................11
1.6 Function Check .................................................................................................. 13
1.7 Self Calibration................................................................................................... 14
1.8 Accessories........................................................................................................ 15
Chapter 2 Operating Basics........................................................................16
2.1 The User’s Interface........................................................................................... 17
2.2 The Menu System.............................................................................................. 19
1.3 The Vertical System ........................................................................................... 21
2.4 The Horizontal System....................................................................................... 22
2.5 The Trigger System............................................................................................ 23
2.6 Input Connector ................................................................................................. 25
Chapter 3 Oscilloscope Functions............................................................. 26
3.1 Setup the Oscilloscope ...................................................................................... 27
3.2 Set Vertical System............................................................................................ 28
3.3 Setup Horizontal System.................................................................................... 34
3.4 Set Trigger System ............................................................................................ 35
3.5 Save/Load.......................................................................................................... 42
3.6 Utility Function ................................................................................................... 43
3.7 Measure Signal .................................................................................................. 48
3.8 The Display System ........................................................................................... 55
3.9 Zoom In/Out and Drag Waveforms .................................................................... 59
3.10 Interpolation ..................................................................................................... 61
3.11 Acquisition Modes ............................................................................................ 63
3.12 Print And Print Preview .................................................................................... 63
Chapter 4 Application Example ..................................................................65
4.1 Simple Measurement ......................................................................................... 66
4.2 Capturing a Single-Shot Signal .......................................................................... 67
4.3 The Application of the X-Y Operation ................................................................. 67
4.5 Taking Cursor Measurements ............................................................................ 69
4.6 Logic Analyzer.................................................................................................... 72
4.7 Waveform Generator.......................................................................................... 75
Chapter 5 Appendix .....................................................................................83
Appendix A: Specifications....................................................................................... 84
Appendix B: Accessories ......................................................................................... 86
Appendix C: General Maintenance .......................................................................... 87
DSO3062L/DSO3062AL
Digital Oscilloscope
USER’S MANUAL 1
General Safety Summary
Review the following safety precautions carefully before operate the device to avoid any
personal injuries or damages to the device and any products connected to it.
To avoid potential hazards use the device as specified by this user’s guide only.
■To Avoid Fire or Personal Injury
■Use Proper Power Cord. Use only the power cord specified for this product and certified
for the country of use.
■Connect and Disconnect Properly. Do not connect or disconnect probes or test leads
while they are connected to a voltage source.
■Connect and Disconnect Properly. Connect the probe output to the measurement
device before connecting the probe to the circuit under test. Disconnect the probe input
and the probe reference lead from the circuit under test before disconnecting the probe
from the measurement device.
■Observe All Terminal Ratings. To avoid fire or shock hazard, observe all ratings and
markings on the product. Consult the product manual for further ratings information before
making connections to the product.
■Use Proper Probe. To avoid shock hazard, use a properly rated probe for your
measurement.
■Avoid Circuit or Wire Exposure. Do not touch exposed connections and components
when power is on.
■Do Not Operate With Suspected Failures. If suspected damage occurs with the device,
have it inspected by qualified service personnel before further operations.
■Provide Proper Ventilation. Refer to the installation instructions for proper ventilation of
the device.
■Do not operate in Wet/Damp Conditions.
■Do not operate in an Explosive Atmosphere.
■Keep Product Surfaces Clean and Dry.
DSO3062L/DSO3062AL
Digital Oscilloscope
USER’S MANUAL 2
Chapter 1 Getting Start
The oscilloscope is small, lightweight, no external power required, portable oscilloscopes!
The oscilloscopes is ideal for production test, research and design and all of the
applications involving analog circuits test and troubleshooting, as well as education and
training.
In addition to the list of general features on the next page, this chapter describes how to do
the following tasks:
System Requirements
Install Software
Install Driver
General Features
General Check
Function Check
Self Calibration
Accessories
DSO3062L/DSO3062AL
Digital Oscilloscope
USER’S MANUAL 3
1.1 System Requirement
To run the oscilloscope software, the needs of computer configuration are as follows:
Minimum System Requirements
Operating System
Window XP/Vista/Win7/Win 8
Processor
Upwards of 1.00G processor
Memory
256M byte
Disk Space
500M disk free space
Screen resolution
800 x 600
Recommended Configuration
Operating System
Windows XP SP3 System
Processor
2.4G Processor
Memory
1G Byte Memory
Disk Space
80G Disk Space
Screen resolution
1024 x 768 or 1280 x 1024 resolution
DPI Setting
Normal Size (96DPI)
DSO3062L/DSO3062AL
Digital Oscilloscope
USER’S MANUAL 4
1.2 Install Software
Caution: You must install the software before using the oscilloscope.
1. While in Windows, insert the installation CD into the CD-ROM drive.
2. The installation should start up automatically. Otherwise in Windows Explorer, switch
to the CD-ROM drive and run Setup.exe.
3. The software Installation is started. Click 'Next' to continue.
DSO3062L/DSO3062AL
Digital Oscilloscope
USER’S MANUAL 5
4. Choose a destination directory. Click 'Next' to continue.
5. Check the setup information. Click Next to start copying of files.
DSO3062L/DSO3062AL
Digital Oscilloscope
USER’S MANUAL 6
6. This Status dialog is displayed during copying of files.
7. Updating Your System Configuration.
8. The installation is complete.
DSO3062L/DSO3062AL
Digital Oscilloscope
USER’S MANUAL 7
1.3 Install Driver
Example: DSO3062AL
1.Connect the A-Type Plug of USB cable to your PC’S USB port.
2.Connect the other A -Type Plug of USB cable to the device’s USB port.
3.New hardware is found.
4.New hardware search wizard starts.
DSO3062L/DSO3062AL
Digital Oscilloscope
USER’S MANUAL 8
5.Select the specific location.
6.New hardware search wizard starts to search the driver.
This manual suits for next models
1
Table of contents
Other Hantek Measuring Instrument manuals
Hantek
Hantek HTM200 Series User manual
Hantek
Hantek CC-650 User manual
Hantek
Hantek HT8000 Series User manual
Hantek
Hantek Hantek2000 Series User manual
Hantek
Hantek HT300B User manual
Hantek
Hantek HDG3000C Series User manual
Hantek
Hantek HSA2030 User manual
Hantek
Hantek HDG1000A User manual
Hantek
Hantek 4032L User manual
Hantek
Hantek DSO8000 Series User manual
