HAMPTON BAY Renwick User manual

52” Renwick

Ceiling Fan by Hampton Bay

(1) Circular Fluorescent Bulb

up to 22-Watt Included

3-Speed Reverse Function for

Year-Round Comfort and Savings

ENERGY STAR Certied

Full Function Remote

Control Included

QUESTIONS, PROBLEMS, MISSING PARTS:

Before returning to your local Home Depot, please call our

Customer Service Team at 1-877-527-0313 or visit www.homedepot.com.

Please reference your SKU (871 861)

or UPC (082392 613853).

Thank you for purchasing this Hampton Bay ceiling

fan. This product has been manufactured with the

highest standards of safety and quality. The nish

of this fan is weather resistant, but over time will

naturally weather and fade.

Safety Rules ...................................... 1

Unpacking Your Fan ........................ 2

Installing Your Fan .......................... 3

Operating Your Fan ......................... 11

Operating Your Remote Control .... 12

Care of Your Fan.............................. 13

Troubleshooting................................ 13

Specications .................................... 14

Warranty Information..................... 15

Table of Contents

UL Model No. 52-RWK

Safety Rules ...................................... 1

Unpacking Your Fan ........................ 2

Installing Your Fan .......................... 3

Operating Your Fan ......................... 11

Operating Your Remote Control .... 12

Care of Your Fan.............................. 13

Troubleshooting................................ 13

Specications .................................... 14

Warranty Information..................... 15

1. To reduce the risk of electric shock, insure electricity

has been turned off at the circuit breaker or fuse box

before beginning.

2. All wiring must be in accordance with the National

Electrical Code ANSI/NFPA 70-1999 and local electrical

codes. Electrical installation should be performed by a

qualied licensed electrician.

3. WARNING: To reduce the risk of re or electric shock,

this fan should only be used with fan speed control part no.

UC7067RK, manufactured by Rhine Electronic Co., Ltd.

4. CAUTION: To reduce the risk of personal injury, use only

the screws provided with the outlet box.

5. The outlet box and support structure must be securely

mounted and capable of reliably supporting a minimum of

35 pounds. Use only UL Listed outlet boxes marked “FOR

FAN SUPPORT.”

6. The fan must be mounted with a minimum of 7 feet

clearance from the trailing edge of the blades to the oor.

7. Avoid placing objects in path of the blades.

8. To avoid personal injury or damage to the fan and

other items, be cautious when working around or

cleaning the fan.

9. Do not use water or detergents when cleaning the fan or fan

blades. A dry dust cloth or lightly dampened cloth will be

suitable for most cleaning.

10. After making electrical connections, spliced conductors

should be turned upward and pushed carefully up into

outlet box. The wires should be spread apart with the

grounded conductor and the equipment-grounding

conductor on one side of the outlet box.

11. Electrical diagrams are for reference only. Light kits that are

not packed with the fan must be UL Listed and marked suit-

able for use with the model fan you are installing. Switches

must be UL General Use Switches. Refer to the instructions

packaged with the light kits and switches for proper assembly.

12. All set screws must be checked and retightened where neces-

sary before installation.

Safety Rules 1.

READ AND SAVE THESE INSTRUCTIONS

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE FOR

FAN SUPPORT WITH THE SCREWS PROVIDED WITH THE OUTLET

BOX. MOST OUTLET BOXES COMMONLY USED FOR THE SUPPORT

OF LIGHTING FIXTURES ARE NOT ACCEPTABLE FOR FAN SUPPORT

AND MAY NEED TO BE REPLACED. CONSULT A QUALIFIED ELECTRI-

CIAN IF IN DOUBT.

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE

BLADE BRACKETS (ALSO REFERRED TO AS “FLANGES”) DURING

ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT OBJECTS IN

THE PATH OF THE BLADES.

TO REDUCE THE RISK OF SHOCK, THIS FAN MUST BE INSTALLED

WITH AN ISOLATION WALL CONTROL/SWITCH.

a. Blade attachment hardware

(15 screws)

b. Mounting Hardware

(1 hanger pin, 1 locking pin)

c. Electric Hardware & Balancing Kit

(3 plastic wire connectors,

blade balancing kit)

d. Extra Bladde Bracket Hardware

(1 screw and lockwasher)

e. Close-to-Ceiling Mount Hardware

(1 rubber gasket)

7. Light Kit

8. Glass Bowl

9. Blades (5)

10. Blade Bracket Set

11. Circline Lamp

12. Hand Unit/Receiver

1. Mounting Plate (inside Canopy)

2. Downrod and Ball Assembly

3. Canopy

4. Decorative Motor Collar Cover (upper)

5. Decorative Motor Collar Cover (lower)

6. Fan Motor Assembly

2. Unpacking Your Fan

IMPORTANT:THIS PRODUCTAND/OR COMPONENTS ARE COVERED BY

ONE OR MORE OF THE FOLLOWING U.S. PATENTS: 5,947,436; 5,988,580;

5,971,573; 6,010,110; 6,010,306; 6,039,541; 6,046,416 AND OTHER

PATENTS PENDING.

Unpack your fan and check the contents. You should have the following items:

Installing Your Fan 3.

Tools Required

Phillips screw driver, straight slot screw

driver, adjustable wrench, step ladder, and

wire cutters.

Mounting Options

If there isn’t an existing outlet box, then read

the following instructions. Disconnect the

power by removing fuses or turning off

circuit breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and

building materials. The outlet box and its

support must be able to fully support the

moving weight of the fan (at least 35 lbs.)

Do not use plastic outlet boxes.

Figures 1, 2, and 3 are examples of different

ways to mount the outlet box.

Outlet Box

Note: You may need a longer downrod to

maintain proper blade clearance when install-

ing on a steep, sloped ceiling. The maximum

angle allowable is 30˚. If the canopy touches

downrod, remove the decorative canopy

bottom cover and turn the canopy 180˚ before

attaching the canopy to the mounting plate.

Outlet Box

To hang your fan where there is an existing

xture but no ceiling joist, you may need an

installation hanger bar as shown in Figure 4

(available at your Hampton Bay retailer).

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR PERSONAL INJURY, MOUNT

FAN ONLY TO AN OUTLET BOX MARKED

ACCEPTABLE FOR FAN SUPPORT AND

USE THE MOUNTING SCREWS PROVIDED

WITH THE OUTLET BOX. OUTLET BOXES

COMMONLY USED FOR THE SUPPORT OF

LIGHTING FIXTURES MAY NOT BE ACCEPT-

ABLE FOR FAN SUPPORT AND MAY NEED TO

BE REPLACED. CONSULT A QUALIFIED ELEC-

TRICIAN IF IN DOUBT.

Figure 1

Figure 2

Figure 4

Figure 3

2. Remove the mounting plate from the canopy

by loosening the four screws on the top of

the canopy. Remove the two non-slotted

screws and loosen the slotted screws. This

will enable you to remove the mounting

plate (Figure 6).

Hanging the Fan

REMEMBER to turn off the pow-

er. Follow the steps below to hang your

fan properly.

NOTE: This ceiling fan is supplied with two

types of hanging assemblies; the standard

ceiling installation using the downrod with

ball and socket mounting, and the “close-to-

ceiling” mounting. The “close-to-ceiling”

mounting is recommended in rooms with

less than 8-foot ceilings or in areas where

additional space is desired from the oor

to the fan blades. When using standard

downrod installation, the distance from the

ceiling to the bottom of the fan blades will be

approximately 14 inches. The “close-to-ceiling”

installation reduces the distance from the

ceiling to the bottom of the fan blades to

approximately 7 inches.

Once you have decided which ceiling

installation you will use, proceed with the

following instructions. Where necessary,

each section of the instructions will note the

different procedures to follow for the two

types of installation.

Standard Ceiling Mounting

1. Remove the canopy ring from the canopy

by turning the ring to the right until it

unlocks (Figure 5).

Figure 5

Figure 6

Figure 7

3. Route the wires exiting the top of the fan

motor through the decorative motor collar

covers (upper and lower) then the canopy

ring. Make sure the slot openings are on

top. Route the wires through the canopy

and then through the ball/downrod assembly

(Figure 7).

4. Loosen, but do not remove, the set screws

on the collar on the top of the motor

housing.

5. Align the holes at the bottom of the down-

rod with holes in the collar on top of the

motor housing (Figure 7). Carefully insert

the hanger pin through the holes in the col-

lar and downrod. Be careful not to jam the

pin against the wiring inside the downrod.

Insert the locking pin through the hole near

Outlet Box)

Outlet Box

the end of hanger pin until it snaps into its

locked position as noted in the circle inset

of Figure 7.

6. Retighten the set screws on the collar on top

of the motor housing.

7. Make sure the grommet is properly installed

in the lower collar cover, then slide thecol-

lar cover (upper and lower) on the downrod

until they set on the motor housing. Be sure

that the canopy and the collar covers are

both oriented correctly.

8. Proceed to “Installing the Fan” section.

“Close-to-Ceiling” Mounting

1. Remove the canopy ring from the canopy

by turning the ring to the right until it

unlocks (Figure 5).

2. Remove the mounting plate from the cano-

py by loosening the four screws on the top

of the canopy. Remove the two non-slotted

screws and loosen the slotted screws. This

FAILURE TO COMPLETELY TIGHTEN THE

THREE SCREWS IN STEP 7 COULD RESULT IN

THE FAN LOOSENING AND POSSIBLY FALLING.

FAILURE TO PROPERLY INSTALL THE LOCK-

ING PIN AS NOTED IN STEP 5 COULD RESULT

IN FAN LOOSENING AND POSSIBLY FALLING.

Figure 8

Figure 9

Figure 10

will enable you to remove the mounting

plate (Figure 6).

3. Remove the decorative canopy bottom cov-

er from the canopy by depressing the three

studs (Figure 8).

4. Remove three of the six screws and lock-

washers (every other one) securing the mo-

tor collar to the top of the fan motor housing

(Figure 9).

5. Place the rubber gasket over the remaining

three screws, route the wires exiting the top

of the fan motor through the canopy ring

(make sure the slot opening are on top),

then proceed to place the ceiling canopy

over the collar at the top of the motor.

(Figure 10).

6. Align the mounting holes with the holes

in the motor and fasten, using the three

screws and lock-washers removed in step 4

(Figure 10).

7. Tighten the mounting screws securely.

Making the Electrical

Connections

REMEMBER to disconnect the power. If

you feel you do not have enough electrical

wiring knowledge or experience, have your fan

installed by a licensed electrician.

Follow the steps below to connect the fan

to your household wiring. Use the wire

connecting nuts supplied with your fan. Se-

cure the connectors with electrical tape.

Make sure there are no loose strands or

connections (Figure 12).

1. Insert the receiver into the ceiling mounting

plate with the at side of the receiver facing

the ceiling.

2. Connect both green wires from the down-

rod and mounting plate to the bare copper

Figure 11

Installing Fan to

the Outlet Box

1. Pass the 120-volt supply wires through the

center hole in the ceiling mounting plate as

shown in Figure 7.

2. Install the ceiling mounting plate on the

outlet box by sliding the mounting plate

over the two screws provided with the

outlet box (Figure 7). When using close-

to-ceiling mounting, it is important that the

mounting plate be level. If necessary, use

leveling washers (not included) between the

mounting plate and the outlet box. Note that

the at side of the mounting plate is toward

the outlet box (Figure 7).

3. Securely tighten the two mounting screws.

4. Carefully lift the assembly up to the

ceiling mounting plate. If using close-

to-ceiling mounting, hang the fan on the

hook provided by utilizing one of the

holes at the outer rim of the ceiling canopy

(Figure 11). If using standard mounting,

WHEN MOUNTING THE FAN ON A SLOPED

CEILING, THE STANDARD BALL/DOWNROD

MOUNTING METHOD MUST BE USED. THE

MOUNTING PLATE MUST BE MOUNTED SO

THAT THE SLOT OPENINGS ARE ON THE

LOWER SIDE BY SLIDING THE MOUNTING

PLATE FROM THE TOP DOWN.

seat the hanger ball in the mounting

plate socket. Make sure the tab on the

mounting plate socket is properly seated in

the groove in the hanger ball (Figure 11).

WHEN USING THE STANDARD BALL/DOWN-

ROD MOUNTING, THE TAB IN THE RING AT THE

BOTTOM OF THE MOUNTING BRACKET MUST

REST IN THE GROOVE OF THE HANGER BALL.

FAILURE TO PROPERLY SEAT THE TAB IN THE

GROOVE COULD CAUSE DAMAGE TO WIRING.

THE HOOK AS SHOWN IN FIGURE 11 IS ONLY

TO BALANCE FAN WHILE ATTACHING WIRING.

FAILURE TO HANG AS SHOWN IN FIGURE 11

MAY RESULT IN HOOK BREAKING, CAUSING

THE FAN TO FALL. HOOK MUST PASS FROM

INSIDE TO OUTSIDE OF CANOPY.

THIS REMOTE CONTROL UNIT IS EQUIPPED

WITH 16 CODE COMBINATIONS TO PREVENT

POSSIBLE INTERFERENCE FROM OR TO OTH-

ER REMOTE UNITS.

THE FREQUENCIES ON YOUR RECEIVER AND

TRANSMITTER HAVE BEEN PRESET AT THE

FACTORY. BEFORE INSTALLING THE RECEIV-

ER, MAKE SURE THE DIP SWITCHES ON THE

RECEIVER AND TRANSMITTER ARE SET TO

THE SAME FREQUENCY. THE DIP SWITCHES

ON THE TRANSMITTER ARE LOCATED INSIDE

THE BATTERY COMPARTMENT.

EACH WIRE NUT (WIRE CONNECTOR) SUP-

PLIED WITH THIS FAN IS DESIGNED TO ACCEPT

UP TO ONE 12 GAUGE HOUSE WIRE AND TWO

WIRES FROM THE FAN. IF YOU HAVE LARGER

THAN 12 GAUGE HOUSE WIRING OR MORE

THAN ONE HOUSE WIRE TO CONNECT TO THE

FAN WIRING, CONSULT AN ELECTRICIAN FOR

THE PROPER SIZE WIRE NUTS TO USE.

Outlet Box

Figure 12

Finishing the Fan

Installation

STANDARD CEILING MOUNTING

1. Align the locking slots of the ceiling canopy

with the two screws in the mounting plate.

Push up to engage the slots and turn clock-

wise to lock in place. Immediately tighten

the two mounting screws rmly.

2. Install the remaining two mounting

screws into the holes in the canopy and

tighten rmly.

3. Install the decorative canopy ring by

aligning the ring’s slots with the screws

in the canopy. Rotate the ring counter-

clockwise to lock in place.

4. You may now proceed to attaching the

fan blades.

CLOSE-TO-CEILING MOUNTING

1. Carefully unhook the fan from the mount-

ing bracket and align the locking slots of

the ceiling canopy with the two screws in

the mounting plate. Push up to engage the

WHEN USING THE STANDARD BALL/DOWN-

ROD MOUNTING, THE TAB IN THE RING AT

THE BOTTOM OF THE MOUNTING PLATE MUST

REST IN THE GROOVE OF THE HANGER BALL.

FAILURE TO PROPERLY SEAT THE TAB IN THE

GROOVE COULD CAUSE DAMAGE TO WIRING.

(Ground) from the outlet box

3. Connect the black wire (AC IN L) from

the receiver unit to the black wire from the

outlet box.

4. Connect the white wire (AC IN N) from

the receiver unit to the white wire from the

outlet box.

5. Connect the white wire (To Motor N) from

the receiver unit to the white wire from the

fan assembly.

6. Connect the black wire (To Motor L) from

the receiver unit to the black wire from the

fan assembly.

7. Connect the blue wire (For Light) from the

receiver unit to the blue wire from the fan.

After wires are connected, carefully tuck them

into the outlet box. Insert the receiver unit into

the mounting plate; make sure the black anten-

na wire sits on top of the receiver unit.

Figure 13

Figure 14

LOCKING SLOTS OF CEILING CANOPY ARE

PROVIDED ONLY AS AN AID TO MOUNTING.

DO NOT LEAVE FAN ASSEMBLY UNATTENDED

UNTIL ALL FOUR CANOPY SCREWS ARE EN-

GAGED AND FIRMLY TIGHTENED.

slots and turn clockwise to lock in place.

Immediately tighten the two mounting

screws rmly.

2. Install the remaining two mounting screws

into the holes in the canopy and tighten

rmly.

3. Install the decorative canopy ring by align-

ing the ring’s slots with the screws in the

canopy. Rotate the ring counter-clockwise

to lock in place.

4. You may now proceed to attaching the fan

blades.

Attaching the

Fan Blades

NOTE: Your fan blades are reversible. Select

the blade side nish that best accentuates your

decor.

1. Attach blade to bracket using the screws

as shown in gure 13. Start a screw into

the bracket. Repeat for the two remaining

screws.

2. Tighten each screw securely.

3. Fasten the blade assembly to the motor by

inserting the alignment post into the slot on

the bottom of the motor and tightening the

blade bracket screws. Please note that the

motor screws are pre-installed into the blade

bracket (Figure 14).

4. Repeat steps 1-3 for the remaining blades.

Table of contents

Other HAMPTON BAY Fan manuals

HAMPTON BAY

HAMPTON BAY AG524-ORB User manual

HAMPTON BAY

HAMPTON BAY 434-972 User manual

HAMPTON BAY

HAMPTON BAY BARROW ISLAND User manual

HAMPTON BAY

HAMPTON BAY Farmington User manual

HAMPTON BAY

HAMPTON BAY BROOKHURST YG268-WH User manual

HAMPTON BAY

HAMPTON BAY Principle User manual

HAMPTON BAY

HAMPTON BAY ETRIS 52 User manual

HAMPTON BAY

HAMPTON BAY 58919 User manual

HAMPTON BAY

HAMPTON BAY Mediterranean 52" User manual

HAMPTON BAY

HAMPTON BAY NORWOOD 52129 User manual

HAMPTON BAY

HAMPTON BAY Victoria User manual

HAMPTON BAY

HAMPTON BAY 178 128 User manual

HAMPTON BAY

HAMPTON BAY 91371 User manual

HAMPTON BAY

HAMPTON BAY Gazebo II Plus User manual

HAMPTON BAY

HAMPTON BAY HALPERT 52169 User manual

HAMPTON BAY

HAMPTON BAY Metarie 795-970 User manual

HAMPTON BAY

HAMPTON BAY CORWIN 56050 User manual

HAMPTON BAY

HAMPTON BAY 705 114 User manual

HAMPTON BAY

HAMPTON BAY Carriage House-2 138 108 User manual

HAMPTON BAY

HAMPTON BAY 7114-01 User manual

HAMPTON BAY

HAMPTON BAY Carlsbad User manual

HAMPTON BAY

HAMPTON BAY Mercer User manual

HAMPTON BAY

HAMPTON BAY Dawson 581 645 User manual

HAMPTON BAY

HAMPTON BAY AC457-WB User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual