HAMPTON BAY 180-471 User manual

Date Purchased

Store Purchased

Model No.

Serial No.

Vendor No.

UPC

180-471

219054

718212343142

Hampton Bay Lifetime Motor Warranty

The retailer warrants the fan motor to be free from defects in workmanship and material

present at time of shipment from the factory for a lifetime after the date of purchase by the

original purchaser. The retailer also warrants that all other fan parts, excluding any glass or

plexiglass parts, to be free from defects in workmanship and material at the time of shipment

from the factory for a period of one year after the date of purchase by the original purchaser.

We agree to correct such defects without charge or at our option replace with a comparable or

superior model if the product is returned to the retailer. To obtain warranty service, you must

present a copy of the receipt as proof of purchase. All costs of removing and reinstalling the

product are your responsibility. Damage to any part such as by accident or misuse or

improper installation or by affixing any accessories, is not covered by this warranty.

Because of varying climatic conditions in the United States this warranty does not cover any

changes in brass finish, including rusting, pitting, corroding, tarnishing or peeling. Brass

finishes of this type give their longest useful life when protected from varying weather

conditions. A certain amount of wobble is normal and should not be considered a defect.

Servicing performed by unauthorized persons shall render the warranty invalid. There is no

other express warranty. The retailer hereby disclaims any and all warranties,

including but not limited to. Those of merchantability and fitness for a particular

purpose to the extent permitted by law. The duration of any implied warranty which

cannot be disclaimed is limited to the time period as specified in the express warranty. Some

states do not allow limitation on how long an implied warranty lasts, so the above limitation

may not apply to you. The retailer shall not be liable for incidental, consequential, or

special damages arising out of or in connection with product use or performance except

as may otherwise be accorded by law. Some states do not allow the exclusion of incidental

or consequential damages, so the above exclusion or limitation may not apply to you. This

warranty gives specific legal rights, and you may also have other rights which vary from

state to state. This warranty supersedes all prior warranties.

Hampton Bay Lifetime Motor Warranty

Table of Contents

SAFETY RULES....................................................................................................

PACKAGE CONTENTS ........................................................................................

INSTALLING YOUR FAN.....................................................................................

HANGING THE FAN.............................................................................................

ELECTRICAL CONNECTIONS ..........................................................................

FINISHING THE INSTALLATION.......................................................................

BLADE INSTALLATION .....................................................................................

............................................

..............................

CARE OF YOUR FAN..........................................................................................

TROUBLESHOOTING........................................................................................

SPECIFICATIONS...............................................................................................

INSTALLING THE MOUNTING PLATE......................................................

CONNECTING THE LIGHT KIT & GLASS SHADE

OPERATING THE TRANSMITTER......................................

1. Before you begin installing the fan, shut power off at the

circuit breaker of the fuse box.

2. Be cautious! Read all instructions and safety information

before installing your new fan. Review accompanying

assembly diagrams.

3. Make sure that all electrical connections comply with

local codes, ordinances, or National Electrical Codes.

Hire a qualified electrician or consult a do-it-yourself

wiring handbook if you are unfamiliar with installing

electrical wiring.

4. Make sure the installation site you choose allows the fan

blades to rotate without any obstructions. Allow a

minimum clearance of 7 feet from the floor and 18 inches

from the tip of the blades to the wall.

5. If you are mounting the fan to a ceiling fan outlet box, use

a U.L. Listed metal octagonal outlet box marked

"Acceptable for Fan Support". Secure the box directly to

the building structure. The outlet box and its support must

be able to support the moving weight of the fan (at least 50

pounds) Do not use a plastic box

6. Caution: To reduce the risk of injury use only the screws

provided with the outlet box in conjunction with the lock

washers provided with the fan.

7. If you are mounting the fan to a joist, make sure it is able

to support the moving weight of the fan (at least 50

1. Safety Rules

8. After you install the fan, make sure that all mounting components

are secured to prevent the fan from falling.

9. Do not insert anything into the fan blades while the fan is

operating.

10. Turn the fan off and wait for the blades to stop completely before

changing the fan direction.

NOTE: The important safeguards and instructions appearing in this

manual are not meant to cover all possible conditions and situations

that may occur. It must be understood that common sense, caution and

care are factors which can not be built into this product. These factors

must be supplied by the person (s) installing, caring for and operating

the unit.

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR OTHER PERSONAL

INJURY, MOUNT FAN UNLY TO A U.L. LISTED OUTLET BOX OR SUPPORTING

SYSTEM MARKED ACCEPTABLE FOR FAN SUPPORT AND USE MOUNTING

SCREWS PROVIDED WITH THE OUTLET BOX OR IN CONJUCTION WITH THE

LOCK WASHERS PROVIDED WITH THE FAN. MOST OUTLET BOXES

COMMONLY USED FOR FAN SUPPORT OF LIGHTING FIXTURES ARE NOT

ACCEPTABLE FOR FAN SUPPORT AND NEED TO BE REPLACED. CONSULT A

QUALIFIED ELECTRICIAN IF IN DOUBT.

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE

HOLDERS WHILE INSTALLING, BALANCING THE BLADES OR CLEANING

THE FAN. DO NOT INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN

BLADES.

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS

WITH ANY SOLID-STATE SPEED CONTROL DEVICE.

WARNING

NOTE

READ AND SAVE ALL INSTRUCTIONS!

Unpack your fan and check the contents. You should have the following items:

1 Fan blades (3)

2. Hanger bracket

3. Canopy

4. Canopy cover

5a. Standard downrod assembly

5b. Minimum-length downrod (for close to

the ceiling installation only)

6. Coupling cover

7. Fan motor assembly

8. Blade holders (3)

9. Mounting plate

10. Light plate

11. Glass shade assembly

13 Watt compact fluorescent bulb

12. Receiver+6 wire nuts

13. Transmitter+holder+2 mounting

screws

14.

a. Mounting hardware:

Wire nuts (3)

b. Blade attachment hardware:

Screws (10)

c. Blade holder hardware:

Screws with lock washers (7)

Package Contents 2.

3. Installing Your Fan

Outlet box

Figure 1

Ceiling

joist

Ceiling

joist

Cross brace

Outlet box

Figure 2

Ceiling joist

or cross brace Parallel

wood brace

Provide strong

support

Recessed

outlet box

Hanger

opening must

be facing up-side

Figure 3

Angled ceiling

maximum

17 angle

Outlet box

Figure 4

Ceiling

joist

Hanger bar

(optional)

Hanger

bracket

Phillips screw driver; slotted screw driver; step-

ladder; wire cutters; electrical tape.

If there isn't an existing mounting box, then read the

following instructions. Disconnect the power by

removing fuses or turning off circuit breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and building

materials. The outlet box and its support must be

able to fully support the moving weight of the fan

(at least 50 lbs.). Use a UL Listed metal outlet box.

Do not use a plastic outlet box.

Figure 1, 2 and 3 are examples of different ways to

mount the outlet box.

Note: You may need a longer downrod to maintain

proper blade clearance when installing on a steep,

sloped ceiling. Longer downrods are available from

your Hampton Bay dealer.

To hang your fan where there is an existing fixture

but no ceiling joist, you may need to install a hanger

bar as shown in Fig. 4 (available at your Hampton

Bay dealer).

Tools Required

Mounting Options

REMEMBER to turn off the power.

Follow the steps below to hang your fan

properly:

Step 1. Secure the hanger bracket to the

ceiling outlet box using screws included

with your outlet box, lock wash e r s

included with the fan. (Fig.5)

Step 2. Loosen the two set screws and

remove the hitch pin and lock pin in the top

coupling of the motor assembly. (Fig. 6)

Step 3. Remove hanger ball from downrod

a s s e m b l y b y l o o s e n i n g s e t s c r e w,

removing the cross pin, and sliding ball off

rod. (Fig.7)

Step 4. Carefully feed fan wires up

through the downrod. (Fig. 8) Thread the

rod into the coupling. Next line up holes

and replace lock pin and hitch pin. Tighten

set screws.

Step 5. Slip coupling cover, canopy cover

and canopy onto dow n r o d. ( Fig. 9)

Carefully reinstall hanger ball onto rod

being sure that cross pin is in correct

position, set screws are tighten and wires

are not twisted.

Step 6. Now lift motor assembly into

position and place hanger ball into hanger

bracket. Rotate until the check groove has

dropped into the registration slot and seats

firmly. (Fig. 10) Rod should not rotate if

this is done correctly.

Outlet box

Hanger bracket

Cross pin

Hanger

ball

Downrod

Supply

wires

Figure 5

Figure 7 Figure 8

Figure 6

Figure 9

Figure 10

Registration

slot

Downrod

Coupling

*Omit coupling

cover when using

the minimum-length

downrod

cover Canopy

Canopy cover

Set screws

Hitch pin Lock pin

Hitch

pin Lock

Set

screws

Hanger ball

Hanging the Fan 4.

WARNING: To avoid possible electrical

shock be sure electricity is turned off at the

main fuse or breaker box before wiring.

NOTE: The Hand Held Remote or Wall

Control units included with your ceiling fan

are equipped with 16 code combinations to

prevent possible interference from or to other

remote units. The frequency switches on your

Receiver and Transmitter units have been

preset at the factory, please re-check to make

sure the switches on both units are set to the

same positions. The frequency settings should

be changed only in case of interference or if a

second or more remote controlled ceiling fans

are installed in the same structure. Any code

combination will operate the ceiling fan and

light as long as the Receiver and Transmitter

units are set to the same codes (Fig. 11)

Step 1. Insert Receiver into Hanger Bracket

with the flat side of the Receiver facing the

ceiling. (Fig. 12)

S t ep 2. Mo t o r t o Rec e i v e r E l e c tr i c a l

Connections: Connect the WHITE wire from

the fan to the WHITE wire marked "TO

MOTOR N" from the Receiver. Connect the

BLACK wire from the fan to the BLACK Wire

marked "TO MOTOR L" from the Receiver.

Connect the BLUE wire from the fan to the

BLUE wire marked "For Light" from the

Receiver. NOTE: If your ceiling fan features

an UP Light: Connect the ORANGE wire

from the fan to the ORANGE wire marked

"For Up Light" from the Receiver. Otherwise

disregard this step and proceed to secure all

wire connections with the plastic wire nuts

provided. (Fig. 13 )

Step 3. Receiver to House Supply Wires

Electrical Connections: Connect the WHITE

wire (Neutral) from the outlet box to the

WHITE wire marked "AC in N" from the

receiver. Connect the BLACK wire (Hot)

from the outlet box to the BLACK wire

marked "AC in L" from the receiver. Secure

all wire connections with the plastic wire

nuts provided. (Fig. 13 )

Step 4. If your outlet box has a GROUND

wire (Green or Bare Copper) connect this

wire to the Hanger Ball and Hanger Bracket

Ground wires. If your outlet box does not

have a Ground Wire, then connect the

Hanger Ball and Hanger Bracket Ground

Wires together. Secure wire connection with

the plastic wire nut provided. (Fig. 13 )

After all connectors are made, check to make

sure there are no loose strands. As an

additional precaution we suggest to secure

the plastic wire connectors to the wires with

electrical tape.

Figure 11

Figure 12

Receiver

Hanger bracket

5. Electrical Connections

Note: The transmitter only works within 40

feet from receiver.

Fan

Figure 13

Figure 14

Outlet box

Hanger

bracket

Hanger

ball

Canopy

cover

White (neutral)

Green or bare

copper (ground)

White ("AC IN N")

White ("to motor N")

Ground

(green)

(Connect to

ground wire on

hanger bracket

if no house

ground wire

exists.)

Outlet box

Black (hot)

Black ("AC IN L")

Black ("to motor L")

Receiver

Blue ("for light")

Blue (light)

Black (motor)

Step 1. Tuck connections neatly into ceiling

outlet box.

Step 2. Slide the canopy up to ceiling and

over the two crews on hanger bracket. Rotate

canopy clockwise. Next, while holding the

canopy with one hand, slide the canopy cover

over the screws and rotate clockwise until

tight. Note: adjust the canopy screws as

necessary until the canopy and canopy cover

are snug. (Fig. 14)

Finishing the Installation 6.

7. Blade

Step 1. Attach fan blade to the blade

ho l de r us i ng t he scr ew s pr o vi de d .

Tighten screws securely. (Fig. 15)

Step 2. Align holes from blade holder to

motor and secure with 2 screws provided.

Repeat procedure with remaining blades.

(Fig. 15)

Installation

Figure 15

Blade

Blade bracket

Screws

8. Installing the

Mounting Plate

Step 1. Remove 1 of the 3 screws from the

mounting ring and loosen the other 2 screws.

(Do not remove)

Step 2. Place the key holes from the mounting

plate over the 2 screws previously loosened from

the mounting ring, turn mounting plate until it

locks in place at the narrow section of the key

holes. Secure by tightening the 2 screws

previously loosened and the one previously

removed. (Fig. 16)

Figure 16

Mounting plate

Mounting ring

Screws

REMEMBER: To disconnect the power.

The fan blades must be already attached to

the fan.

Your fan and light kit though pre-wired

have been disassembled at the factory to

ease in shipping. Please follow these steps

to complete the installation of your fan and

light. TO REDUCE THE RISK OF FIRE

D O N O T E X C E E D M A X I M U M

WATTAGE RATING.

Step 1. Loosen (do not remove) the 3

screws from the mounting plate.

Step 2. Raise and hold the light plate close

to the mounting plate and proceed to do the

wire connections. Connect the white wire

connectors from the light plate and fan,

follow the same procedure with the black

wire connectors. (Fig. 17)

Step 3. Place the light plate key holes over

the 3 screws previously loosened from the

mounting plate, turn light plate until it

locks in place at the narrow section of the

key holes. Secure by tightening the 3

screws previously loosened. (Fig. 17).

Step 4.

fluorescent bulbs (included).

Step 5.Raise glass shade and frame up

against the mounting plate and secure by

tightening with screws provided. (Fig. 18)

Install 1 x 13 Watt compact

(Fig. 18)

Figure 18

Glass shade

and frame

Bulb

Mounting

plate

Figure 17

Connector

plugs

Screws

Mounting

plate

Light plate

Connecting the Light Kit & Glass Shade 9.

This manual suits for next models

Table of contents

Other HAMPTON BAY Fan manuals

HAMPTON BAY

HAMPTON BAY Winthrop User manual

HAMPTON BAY

HAMPTON BAY 420-420 User manual

HAMPTON BAY

HAMPTON BAY 699 810 User manual

HAMPTON BAY

HAMPTON BAY 64183 User manual

HAMPTON BAY

HAMPTON BAY Rapallo 110-083 User manual

HAMPTON BAY

HAMPTON BAY AC457-WH User manual

HAMPTON BAY

HAMPTON BAY AG524PR-FB User manual

HAMPTON BAY

HAMPTON BAY ASHBURTON YG593-BN User manual

HAMPTON BAY

HAMPTON BAY Marlston N375B-BN User manual

HAMPTON BAY

HAMPTON BAY 52652 User manual

HAMPTON BAY

HAMPTON BAY CARROLTON II AM215-ORB User manual

HAMPTON BAY

HAMPTON BAY Isolabella User manual

HAMPTON BAY

HAMPTON BAY 69156 User manual

HAMPTON BAY

HAMPTON BAY 45071-050 User manual

HAMPTON BAY

HAMPTON BAY Eastridge 640-659 User manual

HAMPTON BAY

HAMPTON BAY Middleton 42 inch User manual

HAMPTON BAY

HAMPTON BAY 26829 User manual

HAMPTON BAY

HAMPTON BAY xxx-xxx AL958-BN User manual

HAMPTON BAY

HAMPTON BAY Brookedale User manual

HAMPTON BAY

HAMPTON BAY GAZEBO III User manual

HAMPTON BAY

HAMPTON BAY LK-GZL User manual

HAMPTON BAY

HAMPTON BAY 133-715 User manual

HAMPTON BAY

HAMPTON BAY Trieste User manual

HAMPTON BAY

HAMPTON BAY PORTSMOUTH 51355 User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual