Graco LineLazer V 200HS Instruction Manual
For the application of line striping materials.
For professional use only.
For outdoor use only.
Not for use in explosive atmospheres or hazardous locations.
Maximum Operating Pressure: 3300 psi (22.8 MPa, 228 bar)
Important Safety Instructions
Read all warnings and instructions in this manual and in related manuals before using the equipment.
Be familiar with the controls and the proper usage of the equipment.
Save these instructions.
Related Manuals:
3A3390 Parts 309277 Pump
311254 Gun 3A3428 Auto-Layout Applications Methods
LineLazer V 200HS
Standard Series
LineLazer V 200HS
High Production Series
LineLazer V 200DC
Operation
LineLazer™V 200HS & 200DC Airless Line Stripers
Standard Series and High Production (HP) Series 3A3426H
EN
Use only genuine Graco replacement parts.
The use of non-Graco replacement parts may void warranty.
Cleanup
3A3426HOperation 25
Standard Series
LineLazer V LiveLook Display
26 3A3426HOperation
LineLazer V LiveLook Display
Standard Series
9-10
9-10
LineLazer V LiveLook Display
3A3426HOperation 27
Initial Setup (Standard Series)
The initial setup prepares the striper for operation based
on a number of user entered parameters. Language
selections and the units of measure selections can be
set before you start or changed later.
Language
From Setup/Information select appropriate language by
pressing until the language is outlined.
ENG = English
SPA = Spanish
FRE = French
DEU = German
RUS = Russian
WORLD = Symbols see World Symbol Key, page
61.
NOTE: Language can be changed later.
Units
Press to enter settings and then again to enter
units. Select appropriate units of measure.
US Units
Pressure = psi
Volume = gallons
Distance = feet
Line Thickness = mil
SI Units
Pressure = bar (MPa available)
Volume = liters
Distance = meters
Line thickness = micron (g/m2available)
Paint Specific Gravity = Use UP and DOWN arrows
to set specific gravity. Required to determine paint
thickness.
NOTE: All units can be changed individually at any
time.
Calibration
1. Check rear tire pressure 55 ± 5 psi (379 ± 34 kpa)
and fill if necessary.
2. Extend steel tape to distance greater than 26 ft.
(8m).
ti27827a
ti27828a
26 Ft.
8M
ti27829a
LineLazer V LiveLook Display
28 3A3426HOperation
3. Press to select Setup/Information.
4. Press for Calibration. Set TRAVEL DIST to 25 ft
(7.6m) or longer. Longer distances ensure better1
accuracy, depending on conditions.
\
5. Align part of the unit with 1 foot (30.5cm) on steel
tape.
6. Push to start calibration.
7. Move striper forward. Keep unit aligned with steel
tape.
8. Stop when chosen part of unit aligns with 26-ft (8m),
or distance entered, on steel tape (25-ft./ 7.6m
distance).
9. Push to complete calibration.
• Calibration is not complete when the exclamation
symbol is displayed.
• Calibration is finished when the check mark symbol
is displayed.
10. Calibration is now complete.
Go to Measure Mode (Standard Series), page 30, and
verify accuracy by measuring the tape.
ti27827a
ti27830a
1FT 2FT 3FT 4FT 5 FT 6 F
ti27831a
ti27826a
26 FT 27 FT 28 FT 29 FT 30 FT 31 F25 FT
ti27832a
ti28022a
LineLazer V LiveLook Display
3A3426HOperation 29
Striping Mode (Standard Series)
*Not active in Standard Series. Upgrade to HP Auto
Series, see pages 9 - 10.
Operating in Striping Mode
1. Make sure engine is running.
2. Set pump switch to ON.
3. Pull trigger to spray.
ti27889a
1 2
3
4
5
9
6
7
8
1 2
3
4
5
9
200DC 200HS
6
7
8
Ref. Description
1 Resets Distance, Gallons, Mils
*2 Job logging
3 Scroll between menu screens
4 Line width adjustment buttons
*5 Auto gun buttons
6 MIL thickness. While spraying “Instant MIL avg” is
displayed. When stopped total “Job MIL avg” is
displayed.
7 Total gallons (liters) sprayed
8 Total line length sprayed.
9 Pressure
ti28017a
ti27890a
LineLazer V LiveLook Display
30 3A3426HOperation
Measure Mode (Standard Series)
Measure Mode replaces a tape measure to measure
distances when laying out an area to be striped.
1. Use to select Measure Mode.
2. Press and release . Move striper forwards or
backwards. (Moving backwards is a negative
distance.)
3. Press and release to end measured length. Up
to six lengths are viewable.
Ref. Description
1 Press to start measurement, Press to stop
measurement
2 Hold to reset values to zero
3 Scroll between main menu screens
4 Last measurement taken
ti27834a
1 2
3
4
ti27902a
ti27911a
LineLazer V LiveLook Display
32 3A3426HOperation
Settings
Use to select Setup/Information. Press to
open Settings Menu.
Chooses the machine type. Necessary for accurate
gallon counting.
Use to set time and date.
Use
Set units with
Use to adjust screen contrast to the desired
value.
ti27839b
LineLazer V LiveLook Display
3A3426HOperation 33
Information
Use to select Setup/Information. Press to
open Information Menu.
Displays and logs life data and striper information.
View and test functionality of components.
Logs last four error codes that occurred.
Code Description
02 = Over pressure
03 = No transducer detected
Reset error codes
Stroke Counter
Pressure Transducer
Distance Sensor
Touch Pad Buttons
Engine Voltage
Battery Voltage
Other manuals for LineLazer V 200HS
1
This manual suits for next models
1
Table of contents
Other Graco Construction Equipment manuals
Graco
Graco 24M609 Instruction Manual
Graco
Graco 231-133 B Operation manual
Graco
Graco RoadLazer RoadPak 24M143 User manual
Graco
Graco LineLazer 200HS Guide
Graco
Graco LineLazer ES 1000 Use and care manual
Graco
Graco LineLazer 130HS Instruction Manual
Graco
Graco LineLazer IV 3900 Manual
Graco
Graco LineLazer III 3900 User manual
Graco
Graco LineLazer V 200HS Instruction Manual
Graco
Graco LineLazer V 250SPS Use and care manual
Graco
Graco FieldLazer R300 Instruction Manual
Graco
Graco LineLazer ES 1000 Use and care manual
Graco
Graco LineLazer IV 250MMA Guide
Graco
Graco 231-132 Operation manual
Graco
Graco LineLazer V HP Auto Series User manual
Graco
Graco Line Driver 233725 Instruction Manual
Graco
Graco LineLazert 130HS Manual
Graco
Graco Series A Operation manual
Graco
Graco LineLazer 3000 Operation manual
Graco
Graco 25C528 Parts list manual
