Focal Point NERO CUBE LCD Assembly Instructions

INSTALLATION & USER INSTRUCTIONS

All instructions must be handed to the user for

safekeeping.

MODELS COVERED BY THESE INSTRUCTIONS

NERO CUBE LCD ELECTRIC COMPLETE SUITE IVORY- F500336

NERO CUBE LCD ELECTRIC COMPLETE SUITE OAK- F500337

Focal Point Fires plc.

Christchurch, Dorset BH23 2BT

Tel: 01202 499330

Fax: 01202 499326

www.focalpointfires.co.uk

e : sales@focalpointfires.co.uk

FLOOR MOUNTED ELECTRIC FIRE

Please note : Except where otherwise stated, all rights,

including copyright in the text, images and layout of this

booklet is owned by Focal Point Fires plc. You are not per-

mitted to copy or adapt any of the content without the

prior written permission of Focal Point Fires plc.

Revision A- 03/11

GB IE

NERO

In the event of a problem with

this product, please call our

Customer Care Helpline.

01202 588 601

The Nero LCD electric heater provides convected heating in conjunction with a LCD screen which can display a number of different fuel effects

and scenes.The appliance is designed for indoor use, and can be simply floor mounted in the majority of floor positions anticipated. It can be

located in any household room, with the exception of bathrooms. Read all of the instructions before commencing installation. Retain for future

reference and pass on as necessary to subsequent owners of the appliance.

• DO NOT use this appliance immediately below a fixed socket outlet.

• DO NOT use this appliance in the immediate vicinity of a bath, shower, swimming pool or other area where water/moisture could present a

hazard.

• CAUTION: This appliance must not be used in conjunction with any timer, programmer or thermal control, or any other device that will

switch on the appliance automatically, as a fire risk may occur if the heaters are accidentally covered or displaced.

•WARNING : This heater is not equipped with a device to control the room temperature. Do not use this heater in small rooms when they are

occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.

Do not allow the heater to be covered as this may cause overheating.The appliance must not be placed near curtains or similar material. A

clearance space of at least one metre should be allowed in front of the appliance.

The electrical socket that the appliance uses MUST be easily accessible. Do not route the supply cord directly over or above the heater unit. If

the cord is damaged, it must be replaced by a service agent or competent person.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience

and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

The LCD displays are produced using highly accurate technology, however, black pixels may be found, or red, blue and green pixels may not disap-

pear. This is perfectly normal and within product specification.This should not be regarded as a fault.

The appliance is designed to be floor mounted only. DO NOT RECESS ANY PART OF THE APPLIANCE.

The appliance is supplied with a pre-wired three pin BS1363 plug (13 Amp fuse rated), and 2 metre cable.A standard switched outlet/wall sock-

et, (including earth provision), must therefore be located within this distance, and be easily accessible in order to isolate the supply for mainte-

nance and cleaning. This socket must not be mounted behind or above the appliance.

IMPORTANT:THIS APPLIANCE MUST BE EARTHED.

The appliances are designed to be floor mounted. It is not necessary to secure the surround to the wall, provided it is sited on a firm level sur-

face.

It should be noted that the appliance creates warm convected air currents.These currents move heat from the room surroundings to, and up

the wall surfaces adjacent to the heater.

Operating the heater where impurities in the air, (such as tobacco smoke) exist, may slightly discolour wall finishing. Once the suite is in the

desired location check that it is level and it sits firmly on the floor, i.e. does not rock in any direction, and fits squarely against the wall.

Note: Skirting boards may need to be cut in order to fit the rear of the suite snugly against the wall, Provision must be made in the wall, either

behind the suite, or in one of the sides of the suite to allow the power supply cable to exit.

1.0 PRELIMINARY NOTES

INSTALLATION & USER INSTRUCTIONS

GB IE

2.0 APPLIANCE DATA

3.0 ELECTRICAL INSTALLATION REQUIREMENTS

4.0 SITE REQUIREMENTS

Weight (kg): 37.5 kg

Dimensions (mm): H 855 x W 850 x D 235

Voltage (Volts): 230-240V a.c. 50Hz

Heating Elements: 2 x 900/1000 Watts

Supply Cord: 2 metres

Supply Plug: BS 1363, 13A Fused

Location: Indoor Use

LCD Display: 40 Watts

Section Contents Page No.

1.0 Preliminary Notes 2

2.0 Appliance Data 2

3.0 Electrical Installation Requirements 2

4.0 Site Requirements 2

5.0 Clearances to Combustible Materials 3

6.0 Unpacking the Appliance 3

Section Contents Page No.

7.0 Component Checklist 3

8.0 Operating the Appliance 3

9.0 Safety Cut-Out System 5

10.0 Cleaning and Maintenance 5

11.0 Servicing 5

12.0 Appliance Dimensions 6

DO NOT -mount on a wall.

-recess any part of the appliance into the wall.

- site in a position where curtains or drapes could cover the appliance.

-site in a position where other soft materials could cover e.g. below a coat rack.

-site behind an opening door where mechanical impact/damage could occur.

-site where the supply cable would become a trip hazard.

-sit, stand or forcefully pull on the appliance.

-obstruct, cover or force items into the openings.

-use the heater to dry clothes.

- site/use in an outdoor location(s).

-run the supply cable under carpets.

It is important that the following clearances are maintained from the appliance to combustible materials and are dependant on the desired

mounting location as defined below.

This appliance is designed to be floor mounted only.

The minimum distance from the top of the appliance to a ceiling is 500mm.

The minimum distance to the sides of the appliance is 100mm.

The minimum distance to the front of the applaince is 500mm.

A shelf of any size or design may me mounted above the appliance.

Caution:This appliance is heavy.Always seek assistance whilst unpacking and/or during installation.

Read all the instructions before continuing to unpack or install this appliance. Carefully remove the appliance from its packaging. Check that

the remaining packaging contents correlate with the component checklist below. Please dispose of all packaging with care at your local recycling

centre.

QUANTITY DESCRIPTION

1 Fire suite

1 Remote control handset

1 Mains supply cord

1 Instruction Booklet

Read All Instructions Before Use

Check that the heater outlet grille, mounted at the top of the appliance, is not covered or obstructed in anyway, and ensure the power to the

fire is switched on.The power to the LCD display panel and the heater functions are controlled using four switches mounted underneath the

opening at the right hand side.

Controlling the heater functions

The first switch towards the top, marked (0I), controls the main power to the appliance and switches on the LCD display panel.This feature

can be used independently of the heating features.

The next switch down, marked (*) operates the fan blower without heat, and can be used for cool air circulation. However for this feature,

the main power switch (0I), must also be in the “on” position.

The next switch down, with a “single bar” marked (I) operates the low heat, (1kW), setting.

The switch at the bottom, with “two single bars” marked (II), operates the high heat, (2kW) setting.

To operate the fire in any of the above modes, the top switch marked (OI) must be switched to the “on” position.

To operate the fire, the (OI) switch must be on, followed by the (*)switch to start the blower.To obtain heat from the appliance, the

blower must be on and the I switch must then be operated for LOW heat, followed by the II switch for the HIGH heat setting.

4.0 SITE REQUIREMENTS - CONTINUED

5.0 CLEARANCES TO COMBUSTIBLE MATERIALS

GB IE

6.0 UNPACKING THE APPLIANCE

7.0 COMPONENT CHECKLIST

8.0 OPERATING THE APPLIANCE

Controlling the LCD display

panel - Basic functions

The LCD display may be switched

on and off indepenently of the

heater functions by using the

LCD on/off button as shown in

figure 10.

The appliance is pre-programmed

with nine different scenes as

shown in figures 1 through 9.

These scenes have been specially

edited to run in a seamless loop.

When the appliance is switched

on, the log fire scene will auto-

matically run.To select a different

scene either press the

button or the button. This will skip through all of the different

scenes in order.

Alternatively, to jump directly to a certain scene press one of the scene

select buttons. For example, button will play the log fire scene (see

figure 1). Button will play the twig fire scene (see figure 2) and so

on.

Certain scenes also include sound.This can be muted by pressing the

button.The volume can be lowered by pressing the button

and raised by pressing the button.

During normal operation the footage may occasionally be seen to ‘freeze’

for a fraction of a second.This happens as the scene is recycled to loop

again.This is perfectly normal and should be no cause for concern.

Controlling the LCD display panel - Advanced functions

The LCD display panels are factory set for best all-round performance

and no further adjustment should be necessary. Should you wish how-

ever, certain settings can be changed by using some of the buttons on

the handset and the on-screen menu systems.

8.0 OPERATING THE APPLIANCE- CONTINUED GB IE

Fig. 7 - Abstract scene Fig. 8 - Nature scene Fig. 9 - Aquarium scene

Fig. 4 - Gas fire (medium) Fig. 5 - Gas fire (high) Fig. 6 - Gas fire (Blue Flame)

Fig. 1 - Log fire Fig. 2 - Twig fire Fig. 3 - Coal fire

Figure 10 - Handset basic functions

Previous scene

Next scene

Mute

Standby/ON

Scene select

Volume lower

Volume raise

To access the display set-

tings menu press the

button on the handset.

The menu will appear

with the blue cursor on

the top right icon (figure

11).

Fig. 11

Press the or

button to move the blue

cursor over the icons. In

this example the bright-

ness menu has been

selected (figure 12).

Fig. 12

This appliance has a safety cut-out system fitted which will activate if the air inlets or heater outlets are obstructed. For safety reasons the fire

WILL NOT switch on again automatically. NOTE: The LCD display panel will remain operational if the cut-out is activated, only the fan heater

elements are prevented from operating.

The following procedure must be carried out before the fire can be operated again:

1. Unplug the power supply cable at the outlet socket and place all switches to off at the appliance.

2. Leave the fire OFF for a period of not less than 10 minutes, ensuring any obstructions are removed.

3. Plug in the power supply cable at the outlet socket, and then switch on at the appliance.

If an attempt to switch on is made before the safety cut-out has reset, the heaters may cut-out for a further period of time. If the sequence has

been followed correctly and the heaters still fail to function, check the power supply cable plug is plugged in at the outlet socket. If this is not

the cause, call an electrician.

ALWAYS DISCONNECT THE APPLIANCE AT THE SUPPLY OUTLET SOCKET BEFORE UNDERTAKING ANY CLEANING.

Except for periodic cleaning of dust, there are no specific requirements for care, other than regular cleaning of the general appliance. A wipe

with a dry cloth is normally sufficient. DO NOT use abrasive cleaners as they can damage the finish. Make sure the heater outlet grille (locat-

ed next to the switches), and the air inlet mesh grilles (located either side of the outlet grille) are kept clear of dust, pet hair and other airborne

household matter. These should be vacuum cleaned periodically using a brush attachment.

PLASTIC SCREEN - This should only be cleaned using a suitable glass cleaner.Test on a small area first.

There are no internal user serviceable parts.

Check security of supply cable and connections. If the supply cable becomes damaged, it must be replaced by a service agent or competent per-

son, such as a qualified electrician.

The wires in the cable are coloured in accordance with the following code:

LIVE - Brown

NEUTRAL - Blue

EARTH - Green/Yellow

Refer to Section 2.0,Appliance Data for fuse specification. Excluding fuses, use only genuine manufacturers spare parts available from your sup-

plier.

8.0 OPERATING THE APPLIANCE- CONTINUED GB IE

To change the value of

the selected menu item

press the button.The

value next to that item

will change colour to red.

(figure 13).

Fig. 13

Press the or

button to change the

selected value (figure

14). When you have fin-

ished, move the yellow

bar to ‘Return’ and press

the button.

Fig. 14

Finally, to exit this menu

system, move the blue

cursor to the ‘exit’ sym-

bol at the top right of

the menu, press the

button twice (figure

15).

Fig. 15

The appliance can be switched off at any time, irrespec-

tive of the particular mode selected, by simply switching

the first switch marked (OI) to the “off” position. It is also

recommended to unplug the power supply cable at the

supply outlet when not in use.

9.0 SAFETY CUT-OUT SYSTEM

10.0 CLEANING AND MAINTENANCE

11.0 SERVICING

As our policy is one of continuous improvement and development, we therefore hope that you will understand we must retain the right to amend details and/or specifica-

tions without prior notice.

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.Check with your local authority or retailer for recycling advice.

F861027

12.0 APPLIANCE DIMENSIONS

235

850

5.2

566

565

Figure 16

All dimensions in mm.

GB IE

This manual suits for next models

Table of contents

Other Focal Point Indoor Fireplace manuals

Focal Point

Focal Point OBLIQUE Guide

Focal Point

Focal Point AVANT User guide

Focal Point

Focal Point Exselsior Slimline User manual

Focal Point

Focal Point EKOFIRES EKO 5090 Assembly Instructions

Focal Point

Focal Point KAVACHI - ANDALUSIA Guide

Focal Point

Focal Point Multiflue Inset Guide

Focal Point

Focal Point L23S MIDNIGHT Assembly Instructions

Focal Point

Focal Point F500056 Assembly Instructions

Focal Point

Focal Point BLENHEIM STYLE ELEGANCE Guide

Focal Point

Focal Point Ebony LED Electric Fire Assembly Instructions

Focal Point

Focal Point Envy Guide

Focal Point

Focal Point L23 Series Assembly Instructions

Focal Point

Focal Point F820804 Programming manual

Focal Point

Focal Point L23 CHESHIRE Guide

Focal Point

Focal Point LYCIA Assembly Instructions

Focal Point

Focal Point BLENHEIM STYLE Guide

Focal Point

Focal Point KAVACHI F500181 Assembly Instructions

Focal Point

Focal Point HANNINGTON BRASS F500310 Assembly Instructions

Focal Point

Focal Point L40 PINOIR- NG Assembly Instructions

Focal Point

Focal Point MULTIFLUE GAS FIRE RANGE Guide

Focal Point

Focal Point Blenheim Multiflue Assembly Instructions

Focal Point

Focal Point versailles Guide

Focal Point

Focal Point Odyssey User guide

Focal Point

Focal Point F500116 User manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual