Focal Point REFLECTION User guide

Reflection

Fuel Effect Gas Fire

INSTALLATION, SSERVICING AAND

USER IINSTRUCTIONS

All iinstructions mmust bbehhanded ttotthe uuser ffor ssafekeeping

Revision A 10/03

Country(s) of destination: GB, IE

Focal Point Fires plc, Avon Trading Park, Christchurch, Dorset BH23 2BT

: (01202) 499330

Fax: (01202) 499326

www.focalpointfires.co.uk

e-mail: [email protected]

INSTTALLATTION IINSTTRUCTTIONS

PPrelimminnary NNotes BBefore IInnstallationn

This appliance is an inset live fuel effect gas fire that provides radiant warmth.

The fire is designed to fit into a purpose made builder’s opening, and use natu-

ral draught flues as listed in the Installation Requirements.

The appliance must be installed by a competent person in accordance with

Gas Safety (Installation and Use) Regulations 1998. It is strongly recommended

that a CORGI registered engineer be used for this purpose.

Read all these instructions before commencing installation.

This appliance must be installed in accordance with the rules in force and only

used in a sufficiently ventilated space.

This appliance is factory set for operation on the gas type, and at the pressure

stated on the appliance data plate.

IMPORTANT NNOTES

This fire is an inset live fuel effect gas fire providing radiant warmth. It is designed to operate on natural gas only.

It is the LAW that all gas appliances and fittings are installed by a competent person (such as a CORGI registered

fitter) and in accordance with the Gas Safety (Installation and Use) Regulations 1998, the relevant British

Standards for Installation, Codes of Practice and in accordance with the Manufacturers’ Instructions. The

installation shall also be carried out in accordance with the following regulations:

The Building Regulations issued by the Department of the Environment, the Building Standards (Scotland)

(Consolidation) Regulations issued by the Scottish Development Department.

BS 5871 part 2

BS 5440 part 1

BS 8303

BS 1251

BS 6891

BS 6461 part 1

BS 5482 part 1

Failure ttoccomplyywwith tthese rregulations ccould llead ttopproseccution aand ddeem tthe wwarrantyy

invalid.

This aapplianccemmust bbeiinstalled iinaaccccordanccewwith tthe rrules iinfforcceaand uused oonlyyiinaa

sufficcientlyyvventilated sspacce.

Consult aall iinstrucctions bbefore iinstallation aand uuse ooftthis aappliancce.

This aappliancceiisffree ffrom aanyyaasbestos mmaterial. RRefracctories aand ffuel bbed aare cconstruccted

from cceramiccffibre.

Secction

1.0

2.0

3.0

4.0

5.0

6.0

7.0

8.0

Contentss

Important Notes

Appliance Data

Installation Requirements

Site Requirements

Ventilation

Unpacking the Appliance

Component Checklist

Preparing the Appliance

PaggeNNo.

Secction

9.0

10.0

11.0

11.1

11.2

12.0

13.0

14.0

15.0

16.0

Contentss

Preparing the Opening

Gas Supply

Fitting the Firebox

Cable Fixing

Gas Connection

Fuel Bed Layout

Fitting the frame

Testing & Commissioning

Servicing

Troubleshooting Guide

PaggeNNo.

Note - FFor RRepubliccoofIIreland, rreferencce

sshould bbemmade ttotthe rrelevant sstandardss

ggoverninggiinsstallation, pparticcularly iinrreggard

to fflue ssizinggaand vventilation. SSee IIS813,

ICP3, IIS3277aand aany oother rrulessiinfforcce.

1.0

INSTALLATION RREQUIREMENTS

This appliance MUST NOT be installed into a room containing a bath or shower, or where steam may be

present. The fire has been designed to fit into a pupose made builders’ opening meeting certain dimensional

requirements.

The flue must have an effective height of at least three meters, as measured from the base of the opening to the

top of the flue. Any flue damper plates or restrictors should be removed and no other restriction fitted to the flue.

Where removal is not practical, the restriction must be fixed in the fully open position.

A natural draught flue system is required, and if previously used for solid fuel or oil burning, the flue and chimney

must be swept prior to appliance installation. The flue must be checked before installation by using a smoke pel-

let or similar to ensure proper draw and that leakage is not evident at any joints. Repair and re-test as necessary

before the appliance is installed.

APPLIANCE DDATA Manual Control Versions

Log Version Glass and Pebble Version

Gas Group G20 Natural Gas CAT I2H G20 Natural Gas CAT I2H

Inlet Pressure 20 mbar 20 mbar

Max Energy Input (gross) 6.8 kW 6.8 kW

Min Energy Input (gross) 3.5 kW 4 kW

Pilot Energy Input (gross) 166 W 166 W

Setting Pressure - High (cold) 16.25 mbar (+/- 0.75mbar) 16.25mbar (+/- 0.75mbar)

Setting Pressure - High (hot) 16.5 mbar (+/- 0.75mbar) 16.25mbar (+/- 0.75mbar)

Setting Pressure - Low (hot) 5.5 mbar (+/- 0.5mbar) 6.5mbar (+/- 0.5mbar)

Main Injector Burner Bray cat. 82/440 Bray cat. 82/440

Gas Inlet Connection 8mm compression 8mm compression

Ignition Integral Piezo spark Integral Piezo spark

Spark Gap 3.5 to 4.5mm 3.5 to 4.5mm

Weight ?? Kg ?? Kg

Please see Data Badge affixed to appliance for current data.

This aappliancceiisffor uuse oonlyywwith tthe ggas ttyype, aand aattthe ppressure sstated oontthe aappliancce

Data BBadge, aand iisffor ddeccorative ppurposes.

2.0

3.0

‘A’

‘B’

‘C’

A. Opening height:

615mm Min. / 710mm Max.

B. Opening width:

785mm Min/865mm Max.

C. Opening depth: 350 mm

Min.

D. This area must be flat and ver-

tical to ensure a good seal.

E. Height to hearth: 135mm Min.

F. This area to be flat and level

‘D’

‘E’

‘F’

SITE RREQUIREMENTS

The fireplace opening should be inspected and repairs made where necessary. The flue must be connected to

only one fireplace, and the flue must not vent more than one appliance (i.e. not shared with a gas back boiler).

There must be no opening in the flue apart from the one that the appliance is installed into, and the one venting

the gases into the air. A suitable terminal may be fitted, such as class GC1, as regulations allow.

The opening WIDTH and HEIGHT dimensions should be between 785mm and 865mm wide, and 615mm to

710mm high.

Opening DEPTH should be 350mm or greater. Opening DEPTHS include any plaster or infill panels which form

part of the installation.

This appliance requires a natural draught flue system which may be one of the following;

225mm x 225mm (9in x 9in) brick or stone.

175mm (7in) minimum diameter lined brick or stone.

175mm (7in) minimum diameter twin wall flue conforming to BS 715.

Any existing under grate draught device must be sealed off.

The opening wall must be non-combustible and have adequate flat surface for appliance sealing.

The appliance must be fitted with a non-combustible hearth , the surface of which is at least 12mm thick with a

minimum depth of 300mm and width of 1170mm. The top surface is at least 50mm above the surrounding floor

level.

To enable the products of combustion to be cleared properly up the flue, the outlet on the top of the appliance

must have a minimum 50mm clearance between it and the back wall of the opening or other obstruction. The

area immediately above the outlet must form a smooth path into the flue.

A combustible shelf may be fixed to the wall above the fire, providing that it complies with the dimensions given

below.

A non-combustible shelf may be fitted to within 30mm of the top edge of the fireframe.

Combustible materials, such as wood, may be fitted to within 100mm (4in) of either side of the frame of the

appliance, providing the forward projection does not exceed 100mm (4in).

Any combustible side walls must be at least 500mm to the side of the radiant heat source.

As with all heating appliances, any decorations, soft furnishings, and wall coverings (i.e. flock, blown vinyl and

embossed paper) positioned too close to the appliance may discolour or scorch.

VENTILATION

No purpose provided ventilation is normally required for this appliance. The requirements of other appliances

operating in the same room or space must be taken into consideration when assessing ventilation.

If spillage is detected when commissioning the appliance then amongst other problems there may be insufficient

natural ventilation for the correct operation of the flue. This is potentially a greater problem should the property

be of modern nature. If the appliance does not spill with windows open but does with windows closed, this

proves that lack of ventilation is the problem, if not, it will be the flue at fault. Installation of an air brick is the best

4.0

Maximum ddepth oofsshelf MMinimum ddisstancceffrom bbasseoofffirebox

to uundersside oofsshelf

100mm (4in) 860 mm (34 in)

150mm (6in) 970 mm (38 in)

203mm (8in) 1020 mm (40 in)

5.0

VENTILATION ((continued)

solution. Any ventilation fitted must comply with BS 5871 part 2 and BS 5440 part 2.

Spillage detected during commissioning is almost always a result of poor flue performance, which cannot be cor-

rected by any amount of ventilation.

For Republic of Ireland ventilation may be required, see IS 813, ICP3, IS 327, and any other rules in force.

UNPACKING TTHE AAPPLIANCE

Stand the carton the right way up, cut the strapping bands and remove the top end cap. Read all the instructions

before continuing to unpack or install this appliance.

Remove the box containing the fireframe, the box containing the ceramic logs, and the box containing the burn-

er unit. Remove the cardboard packing pieces, and any bags containing other fittings or parts.

When all loose parts have been removed, the outer sleeve may be lifted off to reveal the appliance. Check that

the components supplied correlate with the checklist given in section 7.0.

Please dispose of the packaging materials at your local recycling centre.

COMPONENT CCHECKLIST

QUAANTITY DESCRIPTION

1 Firebox assembly.

1 Burner unit assembly.

1 Decorative frame.

1 Moulded ceramic fibre log support (Log version only).

8 Individual large ceramic logs (Log version only).

6 Individual small ceramic logs (Log version only).

1 Bag of vermiculite (Log version only).

1 Bag of heat resistant glass crystals (glass fuel bed versions only)

10 Small individual ceramic pebbles (glass fuel bed models only)

1 Set of manufacturers instructions and warranty card.

1 Cable fixing kit comprising; 2 cables, 2 tensioners, 2 clamps, 4 fixing eyes, 4 fibre rawl plugs.

1 Self tapping screw pack.

4 Lengths of self adhesive sealing strip.

1 Rubber grommet.

1 Fitting kit comprising; 1 Inlet restrictor cock, 1 allen key, 2 cable ties.

PREPARING TTHE AAPPLIANCE

Note: EEnssure tthat tthe ggassssupply iissiissolated bbefore ccommenccinggiinsstallation ooftthe aappliancce.

The fireplace opening and environment must be in compliance with the specifications laid down in the

appropriate sections of these instructions. Remove the firebox and burner unit from their cartons and stand upon

a dust sheet or similar. Place the frame, ceramic logs and fixings safely to one side.

Knockout holes are provided in the rear of the firebox for use where concealed pipework is required. Where

necessary, knock out the appropriate hole with a sharp tap from a hammer, and fit the rubber grommet supplied.

A small incision can how be made in the rubber to slip snugly around the outside of the pipe and sleeving.

not iinsstall ooruussetthe aapplianccewwithout tthe ssealssiinpplacce.

If a hole is inadvertently opened, reseal with an intact

grommet. Failure to fit the seal correctly will cause flue suction to act upon the area under the burner, resulting

in poor performance and intermittent cutting out of the burner.

5.0

6.0

7.0

8.0

PREPARING TTHE OOPENING

Before installing the fire, check the flue using a smoke pellet, if alterations to the flue or flue throat are necessary

carry out this check after the work is done. All of the smoke should travel up the flue and exit correctly from the

terminal. If problems are found, DO NOT fit the fire until corrective action is completed.

This appliance is designed to fit into a purpose-made builders open-

ing. The opening WIDTH and HEIGHT dimensions should be between

785mm and 865mm wide, and 615mm to 710mm high. Opening

DEPTH should be 350mm or greater. Opening DEPTHS include any

plaster or infill panels which form part of the installation.

IMPORTANT ::The sstructural iintegrity ooftthe wwall aand fflue/flue tthroat

must bbemmaintained. IItiisrrecommended tthat tthis sstage ooftthe iinstalla-

tion bbeuundertaken bbyaaqqualified bbuilder.

Obtain a suitable lintel. We would suggest either a pre-cast concrete

or steel lintel. Minimum bearing lengths - Generally lintels should be

bedded the correct way up on the supporting bearings in the mortar.

The recommended minimum bearing length for use in 3.5N/mm2

blockwork is 100mm in openings up to 1000mm.

Fit the lintel, and remove brickwork as necessary in order to make an

opening to the correct size. Brick up the old opening and base to the

dorrect height. Ensure the base of the opening is level and flat.

Make good the front wall surface around the opening, ensuring that

the surfaces are true, vertical and flat in order to ensure a good seal

when the firebox is fitted. This front surface must be non-combustible

and capable of withstanding 150OC.

Offer up the firebox to the opening to check the fit is good. Ensure

that it slides in correctly, the sealing face sits flat and square to the

wall or back panel, and that the base is firm on the openings base. At

this stage it is essential to ensure that the spigot outlet of the fire is

not restricted in any way.

Remove the firebox and take any necessary measurements before mak-

ing good and preparing for final installation.

SCREW FIXING. For fixing by screw, mark and drill the fireframe or

base, and the relevant points in the opening or on the wall. Rawlplugs

will again be required. Pre-punched holes are not proided for this pur-

pose to allow you to choose the optimum positions.

GAS SUPPLY. Following preparation for the fixing method, the con-

cealed gas supply, where required, can now be put into place. Refer to

the gas supply section for suggested pipe routes. The ends of the sleev-

ing in which the gas pipe is run should be sealed. The ends of the 8mm

supply pipe should be temporarily sealed to prevent the ingress of debris during fixing.

The non-combustible hearth unit should now be secured in place, which may be protected using surplus pack-

aging material during fitting.

CABLE FIXING. For fixing of the fire by the cable method, see the relevant section. The cable fixing locations

should be marked on the back of the opening and the holes drilled. Fit the fibre rawlplugs and eyebolts to these

holes.

Note: PPlassticcrrawlpluggssaare NNOT ssuitable ffor tthissaappliccation.

9.0

Old fireplace opening

Mark out lintel position

Create opening

to correct size

Insert lintel

Fill in old fireplace opening and

base, to give level, flat bed surface.

These areas MUST be non-combustible

flat and level to ensure good seal.

Make good wall surface

GAS SSUPPLY RROUTING

When the opening is ready for installation of the fire, the gas supply can be routed. An in-line restrictor cock is

supplied with the appliance. It is recommended that this be incorporated into the 8mm supply in an accessible

position, for example, underneath the 'shelf' of the appliance.

A compression fitting is supplied in order that the 8mm supply pipe may be connected directly into the gas valve.

A concealed connection may be made to the appliance by routing the supply pipe into the lower firebox via one

of three knock-out holes. These are located in the sides and rear of the firebox.

The gas pipe must be suitably protected where it passes through fireplace openings. Any sleeving should be

sealed to the pipe at its ends.

The open end of the supply pipe should be sealed temporarily during the installation of the firebox to prevent the

ingress of dirt and dust.

FITTING THE FIREBOX

The firebox may be fitted to the opening by using screw fixing or by the cable kit as described in the relevant

section. Leave the polythene coating in place unitl fitting procedures are complete to eliminate any risk of scratch-

ing the decorative stainless steel finish of the firebox.

To fit the firebox, firstly check the fire goes fully back into the opening.

Secure the fire box by drilling and screwing down the frame of the firebox, or use the cable fixing method.

INSTALLATION BBYCCABLE FFIXING KKIT

Drill the four holes for the rawl plugs, as shown in the diagram. If the fireplace configuration does not allow the

exact layout given, the eyebolts should be positioned as close to the correct layout as possible.

Before finally fitting cables, apply the self adhesive sealing strips. The fireframe must be sealed evenly to the fire-

place opening all around the periphery.

Thread the tensioning cables through the holes in the top of the firebox, then the eyelets, and finally through the

lower holes in the back of the firebox.

Push the appliance back into to fireplace, centralise, and pull the loose tensioning cables

through the holes into the firebox. . Thread the tensioner bolts onto the cables, with the nuts

screwed down close to the tensioner head. Slide the screwed nipple onto the cable, pull

cable tight, and tighten nipple.

The tension of the cable may now be adjusted by

using a suitable spanner on the tensioner nuts to pull

the appliance tightly against the fireplace opening.

Visually inspect the seal and reseat if necessary.

Note: DDO NOT ccut ooff eexccessssccable.

Surplus cable must not be cut off, as it will be impos-

sible to refit the fire after servicing. Coil up the sur-

plus cable, and locate under the shelf at the rear of

the firebox. Two cable ties are provided so as the

cable may be secured out of sight.

Note ::IIfrrunninggaacconccealed ggassssupply, eenssure

ggrommetssaare sseccure aaround iinccominggppipess.

10.0

11.1

11.0

A. 550 mm

B. 440 mm

C. 150 mm

Dimension can

be +/-10mm

GAS CONNECTION

Place burner assembly into the firebox shelf as shown. Ensure that burner sits fully down into the round hole,

and rim of burner is in full contact with the shelf all the way round. Fix the burner to the firebox shelf in the four

screw positions indicated, using

the stainless steel screws and

allen key provided.

Purge the gas supply thoroughly

to remove air and dirt/debris

BEFORE

connection. Now con-

nect the previously installed gas

supply to the control tap and

tighten all joints. Soundness test

installation.

If using an across hearth connec-

tion, ensure the decorative fire-

frame will clear the supply route.

FUEL BED LAYOUT

Please refer to the relevent section of the user manual section of this booklet.

FITTING THE FRAME

The appliance is supplied with a stainless steel frame, which is supplied in 4 pieces. Assemble by following the

enclosed instruction sheet. The frame is held onto the firebox by two mounting brackets at the top and magnets

at the base. The brackets may be adjusted to provide a perfect fit. It is recomended that the brackets be bent to

approximately 40 degrees from the vertical position. Do nnot ooverbend tthe bbrackets.

Lift the stainless steel frame into position on the front of the firebox. The plastic protective film may be removed

from the firebox and frame at this stage.

TESTING AND COMMISSIONING

Turn on and test the gas supply up to the fire for any leaks, in accordance with current Approved Codes Of

Practice (ACOPs).

When the appliance is first used, protective oils coating the firebox may burn off. It is advisable to ventilate the

room during this period, at least one hour.

OPERATING TTHE FFIRE

The control knob of the fire is marked as follows ;

The pilot is visible at the rear of the burner. Push in and turn the con-

trol knob to the SPARK position, and hold there for a few seconds.

Continue turning anti-clockwise through the spark click, ensuring the

pilot has lit. If not, return the knob clockwise, and repeat.

When the pilot lights after the spark, keep the knob depressed for

approximately ten seconds. Now release the knob and the pilot

should stay alight. If not, retry ignition. If the pilot is extinguished dur-

ing use, wait three minutes before repeating the ignition procedure.

To achieve the HIGH setting, push the control knob in slightly and

continue turning anti-clockwise to the large flame position. The main

burner should light after a few seconds.

11.2

12.0

‘OFF’ position

‘SPARK’ position

‘LOW’ position

‘HIGH’ position

13.0

14.0

14.1

OPERATING TTHE FFIRE ((continued)

To decrease the setting to LOW, turn the control knob clockwise to the low flame setting. The flame height may

be adjusted as desired between high and low settings by turning the control knob to the required position

between ‘HIGH’ and ‘LOW’.

To turn to the PILOT position from the HIGH or LOW positions, press the control knob in, and return to the pilot

position and release.

To turn the fire OFF, keep the knob pressed in, return to the off position and release.

SPARK FAILURE

The gap between the spark electrode and the pilot should be 3.5 - 4.5mm to produce a good spark. There should

be no need to adjust this. If under any circumstances the electric spark fails, the pilot may be lit manually by pro-

ceeding with the ignition sequence as previously described, and after turning the control knob through the spark

position, the knob should be held in and the pilot lit with a taper.

SETTING PRESSURE

Remove the screw from the pressure test point, situated on the main injector pipe to the left hand side of the dec-

orative valve cover, and attach a U gauge. Light the fire on the HIGH setting.

The setting pressure should be in accordance with the figures stated on page 2 of these instructions. The fire is

factory set to achieve these pressures, and any significant variation could indicate a supply problem. If the pres-

sure is too high, the gas supply meter may be set incorrectly. This should be checked with the fire running and if

necessary reset by the gas supplier.

If the pressure is too low, then check the meter governor pressure with the appliance running. If this is incorrect

it will need to be reset by the gas supplier. If the setting pressure is too low, but the meter pressure is acceptable,

then a problem in the supply pipework is to be suspected. This will be dirt and debris, kinked or inadequate size

pipes, restriction in a fitting or solder flashing across a joint. (NOTE: you will not get an accurate reading of the

inlet pressure with a pressure gauge on the end of the supply pipe - this is the static pressure in the system. You

must use a T piece and measure the supply pressure with the fire on High - the dynamic pressure).

FLUE SPILLAGE MONITORING SYSTEM

This fire is fitted with a flue spillage safety device (ODS). If the fire shuts down during use for no apparent reason

then several things may be suspected. If a door or window has been opened creating a draught, then pilot dis-

turbance is the problem, and removal of the draught should resolve this. If a grommet seal has been left out of

the firebox then this also will also cause intermittent shutdown (recall your installer to fit). The gas pressure reach-

ing the fire must also be checked (again, recall your installer to check and rectify any problem). The thermocou-

ple connection into the back of the gas control valve may also have worked loose during installation, simply get

the installer to tighten.

If pilot disturbance is not the cause, then the ODS safety system may be in operation. Switch the appliance OFF,

check the flue and carry out any remedial work required. Relight the fire and carry out a spillage test. DO NOT

allow the appliance to be used if it continues to fail a spillage test.

The aeration hole of the pilot must be carefully cleaned out on each annual service to ensure contnued function

of the ODS.

The spillage monitoring system shall not be adjusted, modified, or put out of operation by the installer. Any spare

parts fitted MUST be of a type supplied for the purpose by the appliance manufacturer.

If the fire is not spilling, then further guidance should be sought, using the Troubleshooting section as a guide.

14.3

14.5

14.2

14.1

Other manuals for REFLECTION

Table of contents

Other Focal Point Indoor Fireplace manuals

Focal Point

Focal Point Odyssey User guide

Focal Point

Focal Point EF461LB-E Assembly Instructions

Focal Point

Focal Point BLENHEIM Assembly Instructions

Focal Point

Focal Point COMO L23 User manual

Focal Point

Focal Point Charmough Assembly Instructions

Focal Point

Focal Point POLARIS Assembly Instructions

Focal Point

Focal Point L23 CHESHIRE Guide

Focal Point

Focal Point FPFBQ390 WICHITA FIRE SURROUND WHITE Programming manual

Focal Point

Focal Point F500116 User manual

Focal Point

Focal Point Multiflue Inset Guide

Focal Point

Focal Point Ebony LED Electric Fire Assembly Instructions

Focal Point

Focal Point Rivenhall DS-EHS01-41E Assembly Instructions

Focal Point

Focal Point ALVOR Assembly Instructions

Focal Point

Focal Point L23S MIDNIGHT Assembly Instructions

Focal Point

Focal Point elysee radiant Assembly Instructions

Focal Point

Focal Point PI27 BLENHEIM Assembly Instructions

Focal Point

Focal Point AVANT User guide

Focal Point

Focal Point EVOKE LED ELECTRIC Assembly Instructions

Focal Point

Focal Point L27G Guide

Focal Point

Focal Point F820804 Programming manual

Focal Point

Focal Point EF11-36 PASADENA Assembly Instructions

Focal Point

Focal Point Exselsior Slimline User manual

Focal Point

Focal Point L23S MIDNIGHT Assembly Instructions

Focal Point

Focal Point L30 PIANO NG Assembly Instructions

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual