Focal Point BLENHEIM Assembly Instructions

I STALLATIO & USER I STRUCTIO S

MODELS COVERED BY THESE I STRUCTIO S

LED I SET ELECTRIC FIRE

FRET A D FRAME OPTIO S AVAILABLE

Focal Point Fires plc.

Christchurch, Dorset BH23 2BT

Tel: 01202 499330

Fax: 01202 499326

www.focalpointfires.co.uk

e : sales@focalpointfires.co.uk

LED ELECTRIC FIRE

Revision A - 07/13

GB IE

MODEL SHOW : BLE HEIM LED I SET ELECTRIC FIRE

All instructions must be handed to the user

for safekeeping.

Please note : Except where otherwise stated, all rights,

including copyright in the text, images and layout of this

booklet is owned by Focal Point Fires plc. You are not per-

mitted to copy or adapt any of the content without the

prior written permission of Focal Point Fires plc.

Questions or problems with your appliance?

Don’t take it back to the store

just give us a call on 01202 588601 we’re here to help

lines open between 9am and 5pm, Monday to Friday

The appliance is designed for indoor use, and can be simply floor mounted in the majority of floor positions anticipated. It can be located in any

household room, with the exception of bathrooms. Read all of the instructions before commencing installation. Retain for future reference and

pass on as necessary to subsequent owners of the appliance.

• DO OT use this appliance immediately below a fixed socket outlet.

• DO OT use this appliance in the immediate vicinity of a bath, shower, swimming pool or other area where water/moisture could pres-

ent a hazard.

• CAUTIO : This appliance must not be used in conjunction with any timer, programmer or thermal control, or any other device that

will switch on the appliance automatically, as a fire risk may occur if the heaters are accidentally covered or displaced.

• CAUTIO : Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and

vunerable people are present.

•WAR I G: Children of less than 3 years should be kept away unless continuously supervised. Children aged from 3 years and less

than 8 years shall only switch on/off the applaince provided that it has been placed or installed in its intended normal operating position and

they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged

from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.

•WAR I G: This heater is not equipped with a device to control the room temperature. Do not use this heater in small rooms when

they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.

Do not allow the heater to be covered as this may cause overheating. The appliance must not be placed near curtains or similar material. A

clearance space of at least one metre should be allowed in front of the appliance.

The electrical socket that the appliance uses MUST be easily accessible. Do not route the supply cord directly over or above the heater unit. If

the cord is damaged, it must be replaced by a service agent or competent person.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience

and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

The appliance is suitable for installation into all proprietary surrounds with an opening of 406mm by 559mm (16” by 22”). The appliance is sup-

plied fitted with 2 spacer frames enabling it to be fitted with no need for a recess into a wall or surround back panel. Both spacer frames have

a depth of 57mm. The appliance can be fully recessed if the opening depth is 113mm or greater and neither spacer is used. It may be installed

directly into any proprietary surround which can house this size of rebate, without the need to recess the appliance into a wall opening or fab-

ricate a false chimney breast.

This appliance should be positioned on a firm level surface and in a clean ‘dust free’ environment. If the fire is to be sited in a fire surround then

the suitability of the surround for use with electrical heaters should be established with the fire surround manufacturer.

If fitted into an open draught fireplace, it is advisable to blank off the chimney to reduce the risk of draught through the fire, which may cause

the safety cut out system in the fan heater to operate.

1.0 PRELIMI ARY OTES

I S TA L L AT I O & U S E R I S T R U C T I O S

GB IE

2.0 APPLIA CE DATA

Weight (kg): 14 kg

Voltage (Volts): 220-240V a.c. 50Hz

Rated Power 2 x 900W/ 2 x 1000W

Supply Plug: BS 1363, 13A Fused

Supply Cord: 1.7 Metres

Location: Indoor Use

LED Display: 25 Watts

Section Contents Page o.

1.0 Preliminary otes 2

2.0 Appliance Data 2

3.0 Installation Requirements 2

4.0 Unpacking The Appliance 3

5.0 Component Checklist 3

6.0 Operating the Appliance 3

Section Contents Page o.

7.0 Safety Cut-Out System 3

8.0 Installing The Appliance 4

9.0 Removing the appliance spacer frames 5

10.0 Fitting The Decorative Frame And Front 6

10.1 Fitting The Loose Fuel Bed Options 6

11.0 Cleaning And Maintenance 6

12.0 Guarantee - Terms And Conditions 7

3.0 I STALLATIO REQUIREME TS

DO OT

- site in a position where curtains or drapes could cover the appliance.

-site in a position where other soft materials could cover e.g. below a coat rack.

-site behind an opening door where mechanical impact/damage could occur.

-site where the supply cable would become a trip hazard.

-sit, stand or forcefully pull on the appliance.

-obstruct, cover or force items into the openings.

-use the heater to dry clothes.

- site/use in an outdoor location(s).

-run the supply cable under carpets.

-Mount on a wall.

Read all the instructions before continuing to unpack or install this appliance. Carefully remove the appliance from its packaging and lay on the

floor with it’s back surface downward. Note: DO NOT stand the appliance on its frame as this may cause distortion. Check that the remaining

packaging contents correlate with the component checklist below. Please dispose of all packaging with care at your local recycling centre.

QUA TITY DESCRIPTIO

1 Heater main body

1 Decorative Frame

1 Decorative Fret with aspan door

3 Neoprene securing strips

1 oose coal set (only available with ulworth model)

1 oose pebble set (only available with ulworth model)

1 Instruction Booklet

The heater is operated via the use of two switches, one situated on the left hand side of the canopy and one on the right. The switch on the

left hand side towards the top, marked (0I), controls the main power to the appliance and switches on the ED display panel.

The next switch on the right hand side, with a “single bar” marked (I) and a “two single bars” marked (II) operates the low heat, (1kW) and the

high heat (2kW).

To operate the fire in any of the above modes, the top switch marked (OI) must be switched to the “on” position.

This appliance has a safety cut-out system fitted which will activate if the air inlets or heater outlets are obstructed. For safety reasons the fire

WILL OT switch on again automatically.

The following procedure must be carried out before the fire can be operated again:

1. Unplug the power supply cable at the outlet socket and place all switches to off at the appliance.

2. eave the fire OFF for a period of not less than 15 minutes, ensuring any obstructions are removed.

3. Plug in the power supply cable at the outlet socket, and then switch on at the appliance.

If the appliance fails to operate correctly, repeat the above procedure. If an attempt to switch on is made before the safety cut-out has reset,

the heaters may cut-out for a further period of time. If the sequence has been followed correctly and the heaters still fail to function, check the

power supply cable plug is plugged in at the outlet socket. If this is not the cause, call an electrician.

3.0 I STALLATIO REQUIREME TS - CO TI UED GB IE

4.0 U PACKI G THE APPLIA CE

5.0 COMPO E T CHECKLIST

6.0 OPERATI G THE APPLIA CE

7.0 SAFETY CUT-OUT SYSTEM

Dependent on your installation requirements, you may wish to install the appliance in three different ways.

1: Flat wall – If you are putting the fire against a wall with no recess, you will use both of the

spacers that are fitted to the fire. You will be able to use either the sticky double sided neo-

prene strips, or, secure the fire to the wall using the key hole slots on the rear of the spacer

frame with screws.

2: Semi recessed - If you are putting the fire against a wall with a recess of 60mm or more,

you will be able to remove one of the spacers that are fitted to the fire, so that your fire can

sit further back on the hearth. You will be able to use either the sticky double sided neoprene

strips, or, secure the fire to the wall using the key hole slots on the rear of the spacer frame

with screws. See section 9.0 Removing the appliace spacer frame.

Method 1 - Installation with spacer/s

eoprene – To use the Double sided Neoprene strips, you will need to cut two pieces to

570mm and one piece to 430mm, the long pieces will run from the top to bottom of the rear

facing spacer, and the short piece will run from left to right in between the two side pieces.

Method 2

Screw fixings. Using suitable fixings for your wall or surround, mark the centre of your open-

ing and measure 227mm to the left and then again to the right. From there measure from the

floor 304mm up the wall. This will be the centre of the screw. Fit the screws leaving a 2mm gap

Once you have fitted the screws in place, offer the fire up to the hearth and lift the fire by a

small amount to locate the two keyhole slots on the back of the fire over the screws. When

you lower the appliance, it will now be locked in place.

8.0 I STALLI G THE APPLIA CE GB IE

Flat wall installation Semi recessed installation Fully recessed installation

2mm

3: fully recessed - If you are putting the fire against a wall with a recess of 120mm or more, you will be able to remove both of the spacers

that are fitted to the fire, so that your fire can sit further back on the hearth. To secure the fire to the wall you will be able to use the key

hole slots on the rear of the fire with screws. See section 9.0 Removing the appliace spacer frame.

eoprene – To use the Double sided

Neoprene strips, you will need to cut four pieces

to to fit on the large and small brackets on the

back of the appliance.

Screw fixings. Using suitable fixings for your wall or surround, mark the centre of your

opening, measure 216mm to the left and then again to the right. From there measure from

the floor 562mm up the wall. This will be the centre of the screw.

Once you have fitted the screws in place, offer the fire up to the hearth and lift the appliance

onto the fixing points..

Tools required: Cross headed screwdriver.

Step 1: Ensure the appliance is disconnected at the supply socket before undertaking the

required work.

Step 2: Remove the four screws from the rear spacer located at the rear of the appliance.

Step 3: Remove the outer spacer frame.

Step 4: To remove the second spacer by repeating steps 1, 2 & 3.

8.0 I STALLI G THE APPLIA CE - CO TI UED GB IE

Fixing point

9.0 REMOVI G THE APPLIA CE SPACER FRAMES

The appliance may be supplied with a decorative frame in a variety of finishes.

IMPORTA T : Due to the possibility of sharp edges, care should be taken when handling the frame components. The use of

protective gloves is recommended.

All models : If not pre-fitted, the frame’s should be placed over the outer edges of the fireframe and fixed with magnets. The sides should be

fixed first, followed by the top bar, which overlaps the sides. Push firmly home. A plastic protective film may be applied to the outside of the

frame and should be removed at this stage.

Cast frame models : Remove the decorative frame from it’s protective packaging. The frame is retained onto the firebox with a mounting

bracket at the top of the frame and three magnets on each leg of the frame.

IMPORTA T: Loose fuel bed options are only available with the Lulworth model.

The ulworth ED inset electric fire has the option of either a real coal or pebble fuel bed. Simply

remove the coals or pebbles from their packaging and position the coals or pebbles onto the the

plastic fuel bed, which is below the curved fascia panel.

ALWAYS DISCO ECT THE APPLIA CE AT THE SUPPLY OUTLET SOCKET BEFORE U DERTAKI G A Y CLEA I G.

Except for periodic cleaning of dust, there are no specific requirements for care, other than regular cleaning of the general appliance. A wipe

with a dry cloth is normally sufficient. DO NOT use abrasive cleaners as they can damage the finish. Make sure the heater outlet grille (locat-

ed next to the switches), and the air inlet mesh grillesare kept clear of dust, pet hair and other airborne household matter. These should be

vacuum cleaned periodically using a brush attachment.

The ED light strip is designed and tested to last. 20,000 hours however, should a problem occur with the ED light strip this can be replaced.

The ED light strip can be purchased from Focal Point Fires (please see contact details on front cover). The light strip will be supplied with fit-

ting instructions.

Check security of supply cable and connections. If the supply cable becomes damaged, it must be replaced by a service agent or competent per-

son, such as a qualified electrician.

The wires in the cable are coloured in accordance with the following code:

LIVE - Brown

EUTRAL - Blue

EARTH - Green/Yellow

Refer to Section 2.0, Appliance Data for fuse specification. Excluding fuses, use only genuine manufacturers spare parts available from your sup-

plier.

10.0 FITTI G THE DECORATIVE FRAME A D FRO T GB IE

11.0 CLEA I G A D MAI TE A CE

10.1 FITTI G THE LOOSE FUEL BED OPTIO S

The 3 year guarantee only covers products purchased on or after 1st February 2009. For all gas fires purchased the 3 year guarantee

commences from the date of purchase, provided that the following 3 terms and conditions are adhered to:

Registration is not required.

1. For any claim to be made within the 3 years from date of purchase you will be required to provide and supply us with your proof

of purchase.

2. Your gas fire must have been commissioned by a CORGI/Gas Safe* registered installer, evidence of which you must provide together

with the CORGI/Gas Safe* registration number.

3. Your appliance must have been serviced annually, irrespective of use, by a CORGI/Gas Safe* registered installer, evidence of which

must be provided, such as the receipt.

Please note all consumable items such as any ceramics including; coals, pebbles, the matrix, front strips, side cheeks, rear panels and

tapered rear panels are not covered by the 3 year guarantee.For all Electric fires purchased the 3 year guarantee commences from

the date of purchase, providing that you can supply the proof of purchase. This does not cover consumable items such as pebbles,

coals or ED light strips.

Making a claim is easy.

If you wish to make a claim under our 3 year guarantee and all the terms and conditions for your product have been met then please

submit the following information for the attention of the 3G Service Department to the address below. Alternatively, you can email or

fax.Please note that this does not affect your statutory rights.

Focal Point Fires plc, 3G Service Department, Reid Street, Christchurch, Dorset, BH23 2BT.

Alternatively email: 3g@focalpointfires.co.uk or fax. 01202 499326.

Details required:

1. Name, full address including post code and contact telephone number.

2. Receipt of purchase or credit card statement.

3. Original installers CORGI/Gas Safe* registration number and date of installation (gas fires only).

4. Annual service receipt for every 12 months (gas fires only).

*Gas Safe Register replaced CORGI as the gas registration body in Great Britain and the Isle of Man on 1st April 2009.

12.0 GUARA TEE - TERMS A D CO DITIO S GB IE

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

As our policy is one of continuous improvement and development, we therefore hope that you will understand we must retain the right to amend details and/or specifications without prior notice.

F861224

Other manuals for BLENHEIM

Table of contents

Other Focal Point Indoor Fireplace manuals

Focal Point

Focal Point F500056 Assembly Instructions

Focal Point

Focal Point KAVACHI - ANDALUSIA Guide

Focal Point

Focal Point AVANT User guide

Focal Point

Focal Point versailles Guide

Focal Point

Focal Point EF11-36 PASADENA Assembly Instructions

Focal Point

Focal Point PINOIR Guide

Focal Point

Focal Point LJSF4009E-EHS88 Assembly Instructions

Focal Point

Focal Point F500241 Assembly Instructions

Focal Point

Focal Point ATHERSTONE SLATE ELECTRIC SUITE Assembly Instructions

Focal Point

Focal Point L27G Guide

Focal Point

Focal Point Fuego User guide

Focal Point

Focal Point NERO CUBE LCD Assembly Instructions

Focal Point

Focal Point KAVACHI Assembly Instructions

Focal Point

Focal Point L23S MIDNIGHT Assembly Instructions

Focal Point

Focal Point BLENHEIM HE Assembly Instructions

Focal Point

Focal Point Odyssey User guide

Focal Point

Focal Point Purist Guide

Focal Point

Focal Point L23 Series Assembly Instructions

Focal Point

Focal Point EBONY ELECTRIC Assembly Instructions

Focal Point

Focal Point Osmington Assembly Instructions

Focal Point

Focal Point F820906 Programming manual

Focal Point

Focal Point 18" High-Tech User manual

Focal Point

Focal Point FPFBQ257 BLENHEIM Assembly Instructions

Focal Point

Focal Point REFLECTION User guide

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual