Extech Instruments VB400 User manual
User's Guide
Pen Vibration Meter
Model VB400
www. .com information@itm.com1.800.561.8187
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
VB400-en-GB_v1.2 11/15
2
Introduction
Congratulations on your purchase of the Extech VB400 Meter. The VB400 is designed to provide
easy and accurate velocity and acceleration measurements on industrial machinery. This meter is
shipped fully tested and calibrated and, with proper use, will provide years of reliable service.
Features
Applications for industrial vibration monitoring :
All in one pen type digital vibration meter.
Acceleration, Velocity measurement, RMS measurement value.
Metric & Imperial display unit
Frequency range 10 Hz - 1 kHz, sensitivity designed to meet ISO 2954.
High accuracy and easy to read LCD display.
Complete with the test pin and magnetic base.
Low battery indicator.
IP65 protection.
Safety
This symbol, adjacent to another symbol or terminal, indicates the user must refer to the
manual for further information.
www. .com information@itm.com1.800.561.8187
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
VB400-en-GB_v1.2 11/15
3
Meter Description
1. Display
2. Power Button
3. Hold Button
4. Function Button
5. Battery Cover/Compartment
6. Vibration Sensor
7. Tip Sensing Head
8. Magnetic Base
Display Icons
HOLD HOLD has been activated
ACC Acceleration with units : m/s
2
, ft/s
2
, g
VEL Velocity with units: mm/s, cm /s, inch/s
Low battery
Magnetic base and Tip sensing head
When measuring non-ferrous materials, place the Tip sensing head onto the vibration sensor.
Unscrew the magnetic base from the sensor and screw on the Tip.
When measuring a ferrous surface, place the magnetic base onto the vibration sensor.
Unscrew the tip from the sensor and screw on the magnetic base.
1
2
3
4
5
6
7
8
www. .com information@itm.com1.800.561.8187
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
VB400-en-GB_v1.2 11/15
4
Operation
Preparation for measurements
1. Press the POWER button to turn the meter on.
2. Check that the display is on and that the low battery icon is not on.
3. If the low battery icon appears, replace the batteries.
4. Attach either the sensing head or the magnetic base by screwing it into the vibration sensor.
Measurements
1. Press the MODE button to step through and set the function (velocity or acceleration) and the
units desired.
2. For non-ferrous surfaces, gently hold the meter (as shown) with the sensing tip against the
vibrating surface.
3. For ferrous surfaces, attach the meter to the surface with the magnetic base.
4. The meter must be held perpendicular to the surface to maintain measurement
accuracy
5. Read the measured value in the display.
Data Hold
1. Press the HOLD button to freeze the display and hold the measured value.
2. Press the HOLD button again to exit and return to normal operation
www. .com information@itm.com1.800.561.8187
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
VB400-en-GB_v1.2 11/15
5
Zero Adjustment Procedure
Over time the meter ‘0” may drift by a few digits. This is caused by temperature change, battery
voltage and other ageing factors. Usually this small change is not of significance for typical
measurements. To remove the error:
1. Open the battery compartment
2. Hold the battery lid down so contact is made and the meter can be turned on.
3. With no vibration, adjust the meter zero adjustment until the display reads zero (no minus
sign).
Battery lid (1) and Zero adjustment (2)
Battery Replacement
1 Unscrew the meter’s top cover
2 Lift the battery lid and replace the four AAA batteries, observing polarity
3 Replace the cover.
ISO Vibration Severity Guidelines
ISO 10816 Standards provide guidance for evaluating vibration severity in machines operating in
the 10 to 200Hz (600 to 12,000 RPM) frequency range. Examples of these types of machines are
small, direct-coupled, electric motors and pumps, production motors, medium motors, generators,
steam and gas turbines, turbo-compressors, turbo-pumps and fans. The axis of the rotating shaft
may be horizontal, vertical or inclined at any angle.
1
2
www. .com information@itm.com1.800.561.8187
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
VB400-en-GB_v1.2 11/15
6
Specifications
General Specifications
Display LCD, 20 mm x 28 mm.
Measurement Velocity, Acceleration.
(RMS value).
Mode Acceleration:
g, m/s2, ft/s2
Velocity: mm/s, cm/s, inch/s
Frequency range 10 Hz to 1 KHz
Sampling time Approx. 1 second.
Operating temperature 0 to 50°
C
( 32 to 122°
F
).
Operating humidity < 80% RH.
Power supply DC 1.5V battery ( UM-4/AAA ) x 4 PCs.
Power consumption Approx. DC 12 mA.
Weight 240 g ( 0.53 lb ).
Dimension Meter: 175 x 40 x 32 mm, ( 6.9 x 1.6 x 1.3 inch ).
Sensing head: Round 9 mm Dia. x 30 mm.
Accuracy Specifications
Mode Range Resolution Accuracy
Acceleration 0.5 to 199.9m/s20.1 ±(5%rdg+2digits)
@160Hz, 80Hz, 23±5°C
0.05 to 20.39g 0.01
2 to 656ft/s21
Calibration point: 50m/s2(160Hz)
Velocity
0.5 to 199.9 mm/s
0.1mm/s
±(5%rdg+2digits)
@160Hz, 80Hz, 23±5°C
0.05 to 19.99 cm/s
0.01
0.02 to 7.87inch/s
0.01inch/s
Calibration point: 50mm/s (160Hz)
www. .com information@itm.com1.800.561.8187
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
Table of contents
Other Extech Instruments Measuring Instrument manuals
Extech Instruments
Extech Instruments lcr200 User manual
Extech Instruments
Extech Instruments EasyView EA30 User manual
Extech Instruments
Extech Instruments 380943 User manual
Extech Instruments
Extech Instruments HD755-NIST User manual
Extech Instruments
Extech Instruments 407412 User manual
Extech Instruments
Extech Instruments 480846 User manual
Extech Instruments
Extech Instruments CG104 User manual
Extech Instruments
Extech Instruments 407119 User manual
Extech Instruments
Extech Instruments MO57 User manual
Extech Instruments
Extech Instruments 34135-A User manual
Extech Instruments
Extech Instruments SL510 User manual
Extech Instruments
Extech Instruments HDV7C-A2-39-HD-1 User manual
Extech Instruments
Extech Instruments 380950 User manual
Extech Instruments
Extech Instruments 407750 User manual
Extech Instruments
Extech Instruments SL400 User manual
Extech Instruments
Extech Instruments MA435T User manual
Extech Instruments
Extech Instruments EX845 User manual
Extech Instruments
Extech Instruments PH220 User manual
Extech Instruments
Extech Instruments 407780A User manual
Extech Instruments
Extech Instruments SDL300 User manual
