Extech Instruments SDL800-NIST User manual

USER GUIDE

Vibration Meter

SD Card real-time datalogger

Model SDL800

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176

TestEquipmentDepot.com

2SDL800-en-GB_V1.4 6/15

Introduction

Congratulations on your purchase of the Extech SDL800 Vibration Meter. This meter displays and

stores vibration readings of Acceleration, Velocity and Displacement. Supported measurement units

are meters/s2, ft/s2, g, mm/s, cm/s, in/s, mm and inch. Logged data readings are stored on an SD

card for transfer to a PC. This meter is shipped fully tested and calibrated and, with proper use, will

provide years of reliable service.

Safety

International Safety Symbols

This symbol, adjacent to another symbol or terminal, indicates the user must refer to the

manual for further information.

Meter Description

1. Vibration pickup input jack

2. Measurement Display

3. HOLD and

Backlight key

4. Power ON-OFF

key

5. Up arrow ▲/ UNIT key

6. Down arrow ▼/ Function key

7. ENTER and LOG key

8. SD card slot

9. Vibration pickup

10. DC Adaptor socket, Reset key

and Data output jack

11. SET and Clock key

12. MAX-MIN key

13. Unit of measure Display

Notes: Items listed in “10” are located behind the snap-off compartment cover on meter’s right side.

Battery compartment, tilt stand, and tripod mount are located on the rear of the instrument

3SDL800-en-GB_V1.4 6/15

Getting Started

Power ON-OFF

Power the meter by pressing and holding the power button for at least 1.5 seconds.

Press and hold the power button for at least 1.5 seconds to power OFF the meter.

This meter is powered by six (6) 1.5VDC ‘AA’ batteries or by optional AC adaptor. If the meter

will not switch ON please check that fresh batteries are installed in the rear battery compartment

or, in the case of the AC adaptor, check that the adaptor is connected correctly to the meter and

to an AC source.

Display Backlight

To turn the display backlight ON or OFF, press and hold the backlight button for at least 1.5

seconds. The meter will beep when switching the backlight ON or OFF unless the beeper is

disabled.

Vibration Sensor

Connect the vibration pickup to the cable supplied. Make sure it is firmly attached.

Connect the cable to the meter by attaching it to the BNC connector on the top of the meter.

If the surface to be tested is magnetic, attach the magnetic base to the vibration pickup and attach

the pickup to a flat surface.

If the surface to be tested is not magnetic, hold the pickup against the surface. Do not hold the

cable while making measurements.

Units of Measure

The currently selected unit of measure is shown on the meter’s LCD. To change the unit of

measure, press and hold the UNIT button until the desired unit of measure appears and then

release the UNIT button. The meter begins scrolling through the available units of measure after the

UNIT button has been depressed for at least 1.5 seconds. The saved units will become the default

turn-on units.

UNIT DISPLAY INDICATOR

ACC m/s2

VEL mm/s

cm/s

DISP p-p mm

ACC ft/s2

VEL In/s

DISP p-p inch

4SDL800-en-GB_V1.4 6/15

Function Selection

The currently selected function is shown on the meter’s LCD. To change the function, press and

hold the FUNCTION button until the desired function appears, then release the FUNCTION button.

The available functions are:

RMS: typical selection for Acceleration and Velocity

PEAK: displays the peak value of the vibration

MAX HOLD: displays and holds the max value measured

MAX HOLD Reset

Press and hold the ▲and ▼buttons for 1.5 seconds to clear the max Hold reading.

Data Hold

To freeze a displayed reading on the LCD, momentarily press the HOLD button (the HOLD icon will

appear above the reading). To exit HOLD, press the HOLD button again.

ZERO Adjustment

The ZERO function is used to remove any small offset caused by temperature changes or other

environmental changes. The zero will only work for a display of 10 or less digits.

1. Connect the vibration sensor to the meter

2. Set the measurement function to Acceleration

3. Make sure the sensor is motionless and not subject to any vibrations

4. Press and Hold the ▼and ▲buttons for 1.5 seconds and the meter will zero

Max-Min Reading Record

For a given measurement session, this meter can record the highest (MAX) and the lowest (MIN)

readings for later recall.

1. Press the MAX-MIN button momentarily to access this mode of operation (REC icon appears)

2. The meter is now recording the MAX and MIN readings.

3. Press the MAX-MIN button again to view the current MAX readings (MAX icon appears). The

readings on the display are now the highest readings encountered since the REC icon was

switched on (when the MAX-MIN button was first pressed).

4. Press the MAX-MIN button again to view the current MIN readings (MIN icon appears). The

readings on the display are now the lowest readings encountered since the REC icon was

switched on (when the MAX-MIN button was first pressed).

5. To exit the MAX-MIN mode, press and hold the MAX-MIN button for at least 1.5 seconds. The

meter will beep, the REC-MAX-MIN icons will switch off, the MAX-MIN memory will clear, and

the meter will return to the normal operating mode.

5SDL800-en-GB_V1.4 6/15

Setup Mode

Basic settings at a glance

To view the current configuration of the meter with regard to time, date, and datalogging sampling

rate press the SET button momentarily. The meter will now display the configuration in quick

succession. If the information is missed on the first try, simply press the SET button again until all of

the information is noted.

Accessing the Setup mode

1. Press and hold the SET button for at least 1.5 seconds to access the Setup menu.

2. Press the SET button momentarily to step through the available parameters. The parameter

type is shown on the bottom of the LCD and the current selection for that type is shown above it.

3. When a parameter is displayed that is to be changed, use the arrow keys to change the setting.

Press the ENTER button to confirm a change.

4. Press and hold the SET button for at least 1.5 seconds to exit the Setup mode. Note that the

meter automatically switches out of the Setup mode if no key is pressed within 7 seconds.

The available Setup parameters are listed below. Additional detailed information is provided

below this list:

dAtE

Set the clock (Year/Month/Date; Hours/Minutes/Seconds)

SP-t

Set the datalogger sampling rate

PoFF

Automatic power-off management (Enable or disable the auto-power off function)

bEEP

Set the beeper sound ON/OFF

dEC

Set the numerical format; USA (decimal: 20.00) or European (comma: 20,00)

Sd F

Format the SD memory card

Setting the Clock Time

1. Access the dAtE parameter.

2. Use the ENTER button to step through the selections (year, month, day, hour, minute, second)

3. Use the arrow keys to change a value

4. Press and hold the SET button for at least 1.5 seconds to exit to the normal operation mode (or

simply wait 7 seconds for the meter to automatically switch to the normal operating mode).

5. The clock will keep accurate time even when the meter is switched off. However, if the battery

expires the clock will have to be reset after fresh batteries are installed.

Setting the Datalogger Sampling Time (Rate)

1. Access the SP-t parameter.

2. The sampling rate can be set to 0, 1, 2, 5, 10, 30, 60, 120, 300, 600, 1800 or 3600 seconds.

3. Use the arrow keys to change the digit values.

Press the ENTER button to confirm the entry.

5. Press and hold the SET button for at least 1.5 seconds to exit to the normal operation mode (or

simply wait 7 seconds for the meter to automatically switch to the normal operating mode).

6SDL800-en-GB_V1.4 6/15

Enabling/Disabling the Auto Power OFF Feature

1. Access the PoFF parameter.

2. Use the arrow buttons to select ON or OFF. With the Auto Power OFF feature enabled, the

meter will automatically switch OFF after 10 minutes of inactivity.

3. Press ENTER to confirm setting.

4. Press and hold the SET button for at least 1.5 seconds to exit to the normal operation mode (or

simply wait 7 seconds for the meter to automatically switch to the normal operating mode).

Set the Beeper Sound ON or OFF

1. Access the bEEP parameter.

2. Use the arrow buttons to select ON or OFF.

3. Press ENTER to confirm setting.

4. Press and hold the SET button for at least 1.5 seconds to exit to the normal operation mode (or

simply wait 7 seconds for the meter to automatically switch to the normal operating mode).

Numerical Format (comma or decimal)

European and USA numerical formats differ. The meter defaults to USA mode where a decimal

point is used to separate units from tenths, i.e. 20.00; The European format uses a comma, i.e.

20,00 to separate units from tenths. To change this setting:

1. Access the dEC parameter.

2. Use the arrow buttons to select USA or EUro.

3. Press ENTER to confirm setting.

4. Press and hold the SET button for at least 1.5 seconds to exit to the normal operation mode (or

simply wait 7 seconds for the meter to automatically switch to the normal operating mode).

SD Card FORMATTING

1. Access the Sd-F parameter.

2. Use the arrow buttons to select YES to format the card (select NO to abort). Note that all data

on the card will be lost if formatting is attempted.

3. Press ENTER to confirm selection.

4. Press ENTER again to re-confirm.

5. The meter will automatically return to the normal operating mode when formatting is complete.

If not, press and hold the SET button for at least 1.5 seconds to exit to the normal operation

mode.

System Reset

If the meter’s keys become inoperable or if the display freezes, the Reset button can be used to

reset the instrument.

Use a paper clip or similar item to momentarily press the reset button located on the lower right

side of the instrument .

After pressing the Reset button, switch the instrument ON by pressing and holding the POWER

key for at least 1.5 seconds. If using the power adaptor unplug the adaptor and then plug it back

in again to power the meter.

7SDL800-en-GB_V1.4 6/15

Datalogging

Types of Data Recording

Manual Datalogging: Manually log up to 99 readings onto an SD card via push-button press.

Automatic Datalogging: Automatically log data onto an SD memory card where the number of

data points is virtually limited only by the card size. Readings are logged at a rate specified by

the user.

SD Card Information

Insert an SD card (from 1G size up to 16G) into the SD card slot at the bottom of the meter. The

card must be inserted with the front of the card (label side) facing toward the rear of the meter.

If the SD card is being used for the first time it is recommended that the card be formatted and

the logger’s clock set to allow for accurate date/time stamping during datalogging sessions.

Refer to the Setup Mode section for SD card formatting and time/date setting instructions.

European and USA numerical formats differ. The data on the SD card can be formatted for

either format. The meter defaults to USA mode where a decimal point is used to separate units

from tenths, i.e. 20.00. The European format uses a comma, i.e. 20,00. To change this setting,

refer to the Setup Mode section.

Manual Datalogging

In the manual mode the user presses the LOG button to manually log a reading onto the SD card.

1. Set the sampling rate to ‘0’ seconds as described in the Setup Mode section.

2. Press and hold the LOG button for at least 1.5 seconds and the DATALOGGER icon will appear

on the LCD; the lower portion of the display will show p-n(n= memory position number 1-99).

Note that if PSI is set as the unit of measure it appears as P51 (where a ‘5’ is used as an ‘S’) in

the same area of the LCD where memory locations are shown. This can be disorienting at first.

3. Momentarily press the LOG button to store a reading. The DATALOGGER icon will flash each

time a data point is stored.

4. Use the ▲and ▼buttons to select one of the 99 data memory positions in which to record.

5. To exit the manual datalogging mode, press and hold the LOG button for at least 1.5 seconds.

The DATALOGGER icon will switch off.

8SDL800-en-GB_V1.4 6/15

Automatic Datalogging

In automatic datalogging mode the meter takes and stores a reading at a user-specified sampling

rate onto an SD memory card. The meter defaults to a sampling rate of two seconds. To change the

sampling rate, refer to the Setup Mode section (the sampling rate cannot be ‘0’ for automatic

datalogging):

1. Select the sampling rate in the Setup Mode to a value other than zero.

2. Press and hold the LOG button for at least 1.5 seconds. The meter will flash the DATALOGGER

icon at the selected sampling rate indicating that readings are now being automatically recorded

to the SD card.

3. If a card is not inserted or if the card is defective, the meter will display SCAN SD indefinitely. In

this case, switch the meter OFF and try again with a valid SD card.

4. Pause the datalogger by pressing the LOG button momentarily. The DATALOGGER icon will

stop flashing and the sample rate will display for a short time. To resume logging simply press

the LOG button again momentarily.

5. To terminate the datalogging session press and hold the LOG button for at least 1.5 seconds.

6. When an SD card is used for the first time a folder is created on the card and named VBD01.

Up to 99 spreadsheet documents (each with 30,000 readings) can be stored in this folder.

7. When datalogging begins a new spreadsheet document named VBD01001.xls is created on the

SD card in the VBD01 folder. The data recorded will be placed in the VBD01001.xls document

until 30,000 readings are reached.

8. If the measurement session exceeds 30,000 readings, a new document will be created

(VBD01002.xls) where another 30,000 readings can be stored. This method continues for up to

99 documents, after which another folder is created (VBD02) where another 99 spreadsheet

documents can be stored. This process continues in this same fashion with folders VBD03

through VBD10 (last allowable folder).

SD Data Card to PC Data Transfer

1. Complete a datalogging session as detailed in above in the previous sections. Hint: For the

first few tests, simply record a small amount of test data. This is to ensure that the datalogging

process is well understood before committing to critical, large scale datalogging.

2. With the meter switched OFF, remove the SD Card.

3. Plug the SD Card directly into a PC SD card reader. If the PC does not have an SD card slot,

use an SD card adaptor (available at most outlets where computer accessories are sold).

4. Power the PC and run a spreadsheet software program. Open the saved documents in the

spreadsheet software program (see example spreadsheet data screen below).

9SDL800-en-GB_V1.4 6/15

Spreadsheet data example

RS-232/USB PC Interface

For streaming of data to a PC via the RS232 Output jack, the optional 407001-USB kit (RS232 to

USB cable and driver CD) along with the 407001 software are required.

AC Power Adaptor

This meter is normally powered by six (6) 1.5V ‘AA’ batteries. An optional 9V power adaptor is

available. When the adaptor is used, the meter is permanently powered and the power button will

be disabled.

Battery Replacement and Disposal

When the low battery icon appears on the LCD, the batteries must be replaced. Several hours of

accurate readings are still possible in this condition; however batteries should be replaced as soon

as possible:

Remove the two (2) Phillips screws from the rear of the meter (directly above the top of the tilt

stand).

Remove and safely place the battery compartment and screws where they will not be damaged

or lost.

Replace the six (6) 1.5V ‘AA’ batteries observing polarity.

Replace the battery compartment cover with the two (2) Phillips screws.

All EU users are legally bound by the battery ordinance to return all used batteries to

collection points in your community or wherever batteries / accumulators are sold!

Disposal in the household garbage is prohibited!

10 SDL800-en-GB_V1.4 6/15

Specifications

Display Backlit LCD; LCD size: 52 x 38mm (2 x 1.5”)

Status indicators Over-range audible beep and low battery display icon

Frequency Range 10Hz to 1kHz

Datalogger Sampling Rate AUTO LOGGING: From 1 to 3600 seconds.

MANUAL LOGGING: Set the sampling rate to ‘0’ seconds

Memory Card SD memory card; 1G to 16GB size

Data Hold Freeze the displayed reading

Memory Recall Record and Recall the Maximum and Minimum readings

Display update rate Approx. 1 second

Data Output RS-232 / USB PC computer interface

Operating Temperature 0 to 50

C (32 to 122

Operating Humidity 85% R.H. max.

Auto Power OFF After 10 minutes of inactivity (can be disabled)

Power Supply Six (6) 1.5 VDC batteries (optional 9V AC adaptor)

Power Consumption Normal operation (backlight and datalogger OFF): approx. 5mAdc

With backlight OFF and datalogging ON: approx. 25mAdc

With backlight ON add approx. 12mAdc

Weight 343g (0.75 lbs.) w/ batteries; 241g (0.53 lbs.) w/o batteries

Dimensions Meter: 182 x 73 x 47.5mm (7.1 x 2.9 x 1.9”)

Vibration sensor: round 16mm (0.63”) diameter, 37mm (1.46”)

length

Electrical Specifications

Function

Unit

Range

Accuracy

Acceleration m/s

0.5 to 199.9 m/s

± ( 5%rdg + 2 d )

@ 80 and 160Hz

0.05 to 20.39 G

ft/s

2 to 656 ft/s

Calibration Point: 50 m/S^2 ( 160 Hz )

Velocity mm/s 0.5 to 199.9 mm/s

± ( 5%rdg + 2 d )

@ 80 and 160Hz

cm/s 0.05 to 19.99 cm/s

inch/s 0.02 to 7.87 inch/s

Calibration Point: 50 mm/s ( 160 Hz )

Displacement

mm 0.003 to 1.999 mm ± ( 5%rdg + 2 d )

@ 80 and 160Hz

inch 0.078 inch

Calibration Point: 0.141 mm ( 160 Hz )

Above specification tests under the environment RF Field Strength less than 3 V/M & frequency less

than 30 MHz only and 23±0.5°

This manual suits for next models

Table of contents

Other Extech Instruments Measuring Instrument manuals

Extech Instruments

Extech Instruments FM200 User manual

Extech Instruments

Extech Instruments 461891 User manual

Extech Instruments

Extech Instruments 401027 User manual

Extech Instruments

Extech Instruments MO750 User manual

Extech Instruments

Extech Instruments MW12 User manual

Extech Instruments

Extech Instruments 401025 User manual

Extech Instruments

Extech Instruments 380580 User manual

Extech Instruments

Extech Instruments MA145 User manual

Extech Instruments

Extech Instruments MO270 User manual

Extech Instruments

Extech Instruments SL10 User manual

Extech Instruments

Extech Instruments SDL100-NIST User manual

Extech Instruments

Extech Instruments 451104 User manual

Extech Instruments

Extech Instruments LT10 User manual

Extech Instruments

Extech Instruments 380560 User manual

Extech Instruments

Extech Instruments 407740 User manual

Extech Instruments

Extech Instruments RH520 User manual

Extech Instruments

Extech Instruments SDL310 User manual

Extech Instruments

Extech Instruments TachIR RPM10 User manual

Extech Instruments

Extech Instruments VB450 User manual

Extech Instruments

Extech Instruments EN510 User manual

Extech Instruments

Extech Instruments 382400 User manual

Extech Instruments

Extech Instruments MO260 User manual

Extech Instruments

Extech Instruments 407119 User manual

Extech Instruments

Extech Instruments MA130 User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual