Duratuf SG3025 User manual

ASSEMBLY INSTRUCTIONS

SG3025

BASE SIZE: 3.020m x 2.520m

BEFORE YOU START:

 Read all instructions carefully

 Identify all parts and check quantities against parts list

 Select a level site

 Do not mark cladding with pencil as lead can cause corrosion to cladding

 During assembly, ensure all drill filings are removed between layers of steel, before riveting together

SAFETY:

 Do not attempt to build your shed in high winds

 Beware of sharp edges, recommend use of gloves

 Protect your eyes and ears

 For ease of assembly, use a friend to help

TOOLS REQUIRED:

WARRANTY REQUIREMENTS:

Following are the minimum requirements for cladding used in Sentry Sheds.

 Wash all surfaces annually using a hose and soft nylon brush.

 Within 2 km of coast – wash every 3 months as above. After a storm, wash the cladding and the gutters as soon

as possible to remove any highly corrosive salt deposits.

 Volcanic Ash Fallout – wash as soon as possible, removing fall out from roof and gutters.

 Do not allow manures, chemicals or other corrosive materials to have direct contact with cladding.

DRILL RIVETER 3.5 & 10 DRILL BIT

HAMMER

LADDER

TAPE MEASURE PEN

NAIL PUNCH

CONGRATULATIONS ON PURCHASING A DURATUF SENTRY SHED.

BEFORE YOU BEGIN THE ASSEMBLY PLEASE NOTE SOME IMPORTANT POINTS

SQUARE DRILL BIT

SG3025 PARTS LIST

DESCRIPTION QTY DIAGRAM

CLADDING FLASHINGS

Front/Back Wall

1.850 m 9

Door Sides

1.810 m 4

Gable Wall Angled

1.880 m (Measurement along

centre of sheet) 4

Door Jamb

1.850 m 2

Gable Wall Angled

1.940 m (Measurement along

centre of sheet) 4

Door Brace

1.160 m 2

Gable Wall Angled

2.000 m (Measurement along

centre of sheet) 2

Door Brace

0.915 m 2

Roof

1.350 m 12

Weatherstrip

1.810 m 1

Door 3/4 Sheet

1.810 m 3

Barge

1.350 m 4

TIMBER

Ridge Flashing

1.800 m 2

Bottom Plates - H4 (Green)

Front/Back

3.020 m 2

Padbolt Support (Front)

0.140 m 1

Bottom Plates - H4 (Green)

Sides

2.520 m 2

Padbolt Support (Back)

0.070 m 2

Top Plate - H1 (Red)

Front/Back

3.020 m 2

Spouting

3.055 m 2

Top Plate - H1 (Red)

Sides

2.520 m 2

HARDWARE

Ridge Beam - H1

90 x 45

3.020 m 1

Hardware Pack 1

Jack Studs - H1

45 x 60

0.200 m 2

Paint & Brush 1

FLASHINGS OPTIONAL

Door Top/Bottom

0.945 m 2

Bolt Down Kit 1

Door Top/Bottom

0.495 m 2

DATE:

PACKED BY:

DESCRIPTION QTY DIAGRAM

CHECKED CHECKED

PARTS LOCATION

Door Sheets

Padbolt Support

Top Plate Back

Side Wall Sheets

Roof Sheets

Top Plate Side

Top Plate Front

Bottom Plate Front

Bottom Plate Side

Back Wall Sheets

Front Wall Sheets

Door Jambs

Front Wall Sheet Door Side Flashing Hinge

Door Brace

Door Top/Bottom

Ridge Beam

Jack Stud

Ridge Flashings—x 2

ASSEMBLE FRONT

PANEL

ASSEMBLE WALLS

ASSEMBLE ROOF

SECURE SHED

ASSEMBLE BACK

PANEL

ASSEMBLE SIDE

PANELS

LAY FOUNDATION

ASSEMBLE DOORS

QUICK OVERVIEW

Barge Flashing

Spouting

FOUNDATION

SENTRY WOODEN FLOOR

 The optional Sentry kitset wooden floor is precut and designed to

be fitted into the shed after the shed is assembled.

 Assemble shed as per instructions and fit floor last.

(see page 13 for details).

CONCRETE SLAB FOR RAISED BASE PLATE SHED

To build a raised concrete slab for your shed to sit on, we recom-

mend the following:

 The raised slab size should be 15mm smaller than the base

size of the shed and at least 30mm above ground line.

 The slab should be 80mm thick in the middle and 100mm

thick around the edges.

 The slab should be laid on a solid or compacted base.

 Plastic sheeting under slab will prevent moisture coming

through from underneath.

 During construction, you may raise the bottom timber

plate to allow the wall cladding to protrude 20mm below

the bottom plate. This will stop water flowing between

the bottom plate and the concrete floor.

See note on page 7.

80mm

100mm

7.5mm

20mm

Concrete Floor

Base Plate

Wall Cladding

RAISED BASE PLATE OPTION

(For sheds placed on a raised concrete floor)

No doubt by now you will have decided what sort of base you are putting down.

Please read the section that applies to your situation.

If you choose to pour a concrete base you will need to decide whether you wish to raise the base plate of your shed.

This allows the cladding to protrude below the surface of the concrete and ensures a water tight pad.

See concrete pad specifications below

By choosing this option you will need to make the pad to the specification below.

ASSEMBLE DOORS

SELECT:

3 x 1.810 m Door Sheets (Narrow)

2 x 0.945 m Door Top/Bottom Flashings

2 x 0.495 m Door Top/Bottom Flashings

4 x 1.810 m Door Side Flashings

2 x 1.160 m Door Brace Flashings

2 x 0.915 m Door Brace Flashings

1 x 1.810 m Weatherstrip

6 x Hinges

1 x Padbolt Support Flashing

103 x Rivets

SMALL DOOR:

 Assemble small door in same way as large door using 0.495 m top and bottom flashings.

 Before screwing on 0.915m door braces, attach weather strip flashing to back of door side flashing using six rivets

ensuring it protrudes 20mm out from door side.

STEP 1:

 Lay out 2 x door sheets on a flat surface

making sure narrow pans are on the outside.

 Rivet sheets together ensuring ends are

flush with each other.

STEP 2:

 Position door side flashings and 0.945m top

and bottom flashings and assemble door as

shown.

 Drill and rivet as per diagram.

STEP 4:

 On the back of the door, place door braces in posi-

tion as shown in fig.3.

 Ensure that the top and bottom ends of the braces

are under the door flashings as shown in fig.4. and

opposite ends of the braces overlap in the middle.

 Rivet door brace flashings onto back of door as

shown. Where possible, rivet from front of door.

STEP 3:

 Attach hinges to door side flashing using rivets provided.

Ensure hinge is flush with back of door, and 60mm in from

each end as per fig.2.

 Using one rivet, attach padbolt support as shown in fig. 1.

fig.1

NARROW PANS

fig.3

fig.4

fig.2

ASSEMBLE SIDE PANELS

SELECT:

4 x 1.880 m Gable Wall Sheets (Angled)

4 x 1.940 m Gable Wall Sheets (Angled)

2 x 2.000 m Gable Wall Sheets (Angled)

2 x 2.520 m Top Plates (Red)

2 x 2.520 m Bottom Plates (Green)

120 x 30mm Galv Clouts

16 x Rivets

IMPORTANT—IF YOU CHOOSE TO RAISE YOUR TIMBER

BASE PLATE –READ THE FOLLOWING;

For sheds with Raised Base Plate option only (see page 5), deduct

30mm from measurement shown between Top and Bottom Plates on

all wall panels, so cladding protrudes 20mm below bottom plate.

STEP 1:

 Lay out 1 x Top plate and 1 x Bottom plate on a flat surface as shown

(corner cut-outs to face outwards). Measurements between Top and

Bottom plates are critical to ensure wall panels fit together.

STEP 2:

 Place 2 x 1.880 m wall sheets, 2 x 1.940 m wall sheets and 1 x

2.000m wall sheet on top of timber plates with bottom of sheets

flush with each other.

 Rivet sheets together on overlaps as shown.

STEP 3:

 Nail wall sheets to the Top Plate at each end making

sure that the top corners of the sheets are flush with

the top of the Top Plate and that the sides of the wall

sheet overhang the Top Plate by approx 15mm as

shown.

 Check that the Top Plate is straight then nail the

Wall sheet to the Top Plate, 2 clouts per pan.

(see fig. 1).

Std Shed — Bottom Plate will protrude below

wall sheet by approximately 10mm.

Raised base plate shed — Wall sheet will protrude

below the Bottom Plate by 20mm.

STEP 4:

 Nail the wall sheets to the Bottom Plate at each end ensuring each side

of wall sheets overhangs the end of Bottom Plate by 15mm. Check that

the distance between the Top and Bottom Plates is correct. (As per

diagram in step 1)

 Check that the Bottom Plate is straight then nail the wall sheets to the

Bottom Plate, two clouts per pan (see fig. 1).

fig.1

RIB

PAN

CLOUT

TIMBER PLATE

TOP PLATE

BOTTOM PLATE

RIVET

RIVET RIVET

TOP PLATE

15mm 15mm

BOTTOM PLATE

1810mm 1810mm

TOP PLATE

BOTTOM PLATE

15mm 15mm

1810mm 1810mm

TOP PLATE

REPEAT THESE STEPS TO MAKE SECOND SIDE WALL PANEL

15mm

RIVET

ASSEMBLE BACK PANEL

SELECT:

6 x 1.850m Wall Sheets

1 x 3.020 m Top Plate (Red)

1 x 3.020 m Bottom Plate (Green)

72 x 30mm Galv Clouts

10 x Rivets

STEP 1:

 Lay out 1 x Top Plate and 1 x Bottom Plate on a

flat surface as shown (corner cutouts to face in-

wards).

STEP 2:

 Place 6 x 1.850 m wall sheets on top of timber

Plates with bottom of sheets flush with each oth-

er.

 Rivet the sheets together on overlaps as shown.

STEP 3:

 Nail the wall sheets to the Top Plate at each end making sure

that the top of the sheets are flush with the top of the Top

Plate and that the sides of the wall sheets overhang the Top

Plate by 15mm as shown.

 Check that the Top Plate is straight then nail wall sheets to

the Top Plate, using two clouts per pan.

STEP 4:

 Nail the wall sheets to the Bottom Plate at each end,

ensuring that each side of the wall sheets overhangs the

Bottom Plate by 15mm and that the distance between

the Top and Bottom Plates is correct. (As shown)

 Check that the Bottom Plate is straight then nail

wall sheets to the Bottom Plate, using two clouts per pan.

Std Shed — Bottom Plate will protrude below wall sheet by

approximately 10mm.

Raised base plate shed — Wall sheet will protrude below

the Bottom Plate by 20mm.

TOP PLATE

BOTTOM PLATE

1811mm 1811mm

TOP PLATE

15mm 15mm

1811mm 1811mm

BOTTOM PLATE

15mm 15mm

TOP PLATE

IMPORTANT—IF YOU CHOOSE TO RAISE YOUR TIMBER

BASE PLATE –READ THE FOLLOWING;

For sheds with Raised Base Plate option only (see page 5), deduct

30mm from measurement shown between Top and Bottom Plates on

all wall panels, so cladding protrudes 20mm below bottom plate.

TOP PLATE

ASSEMBLE FRONT PANEL

BOTTOM PLATE

1811mm 1811mm

15mm 15mm

530mm 1460mm

TOP PLATE

DOOR OPENING

SELECT:

3 x 1.850 Wall Sheets

1 x 3.020 Top Plate (Red)

1 x 3.020 Bottom Plate (Green)

2 x 1.850 Door Jamb Flashings

40 x 30mm Galv Clouts

28 x Rivets

STEP 1:

 Lay out 1 x Top Plate and 1 x Bottom Plate on a flat

surface as shown

STEP 2:

 Using 2 x 30mm clouts, nail the Door Jamb Flashing flush with

the top of the Top Plate at the correct measurement as shown

in plan view. Pre drill holes using a 3.5mm drill bit.

 Check the distance between the top and bottom plates then use

a further 2 x 30mm clouts to nail the Door Jamb Flashings to

the bottom Plate. Pre drill holes.

NOTE: Door can be hinged on either side.

STEP 4:

 Place the doors on the panel (In open position, approx

20mm below top of top plate). Using four rivets, rivet the

top and bottom hinges to the Door Jamb Flashing, ensuring

door closes properly.

 Fit remaining rivets.

STEP 3:

 Place 3 x Wall Sheets on timber plates and rivet the sheets

together as shown.

 Ensure that the top of the sheet is flush with the top of the

Top Plate and that the sides of the wall sheet overhang the

Top Plate by 15mm as shown. Nail wall sheets to Top Plate

(two clouts per pan).

 Nail the wall sheets to the Bottom Plate making sure that the

Plates are the correct distance apart and that the sides of the

wall sheets overhang the Bottom Plate by 15mm.

 Drill & rivet Door Jamb Flashings to wall sheets using four

rivets equally spaced on each side.

NOTE: The Doorway is standard at 530mm from left-hand end.

To shift the doorway to the right-hand side of the front

wall, simply measure 530mm from the right-hand end.

Plan View

IMPORTANT—IF YOU CHOOSE TO RAISE YOUR TIMBER

BASE PLATE –READ THE FOLLOWING;

For sheds with Raised Base Plate option only (see page 5), deduct

30mm from measurement shown between Top and Bottom Plates on

all wall panels, so cladding protrudes 20mm below bottom plate.

TOP PLATE

TOP

PLATE

DOOR

JAMB

NAIL

Table of contents

Other Duratuf Outdoor Storage manuals

Popular Outdoor Storage manuals by other brands

USP

USP DURAMAX 10 Ft x 8 Ft StoreMax Plus owner's manual

TYGO

TYGO Nyland Building Instruction

Viking

Viking SD5300SS Use & installation guide

USP

USP DURAMAX Apex Pro 10.5 Ft x 8 Ft 40116 owner's manual

ModuLaro

ModuLaro Lojo WC202200 manual

Lifetime

Lifetime 6418 owner's manual

rollaway container

rollaway container ARPCA24 manual

X-METAL

X-METAL 4065 owner's manual

Outdoor Life Products

Outdoor Life Products FP2030 F Assembly instructions

Royalcraft

Royalcraft Faro 295L Storage Box Assembly instructions

Riverlea

Riverlea Duratuf KIWI KS3 Assembly instructions

OLT

OLT GS84D-FJ-Plywood Assembly manual

Rubbermaid

Rubbermaid 5L45 manual

garofalo

garofalo TUSCANY EVO user manual

Eden

Eden CA2988 Assembly instructions

Palram

Palram CANOPIA RUBICON 6x10 How to assemble

Suncast

Suncast 774098 Assembly manual

Lifetime

Lifetime 60186 Assembly instructions