Dimplex MULTIFIRE DF3015 User manual

Service Manual

30” Self Trimming Fireplace





DF3015

DFB8842

7400220000R04

  

00 Feb 28, 07

01 Jul 22, 09

02 1111 Oct 21, 09

03 11873 Feb 11, 10

04 Jan 5, 2012

In keeping with our policy of continuous product development, we reserve the right to make changes without notice.



1367 Industrial Road Cambridge ON Canada N1R 7G8

1-888-346-7539 www.dimplex.com

: Always read this manual rst before attempting to service this

replace. For your safety, always comply with all warnings and safety instructions contained in this

manual to prevent personal injury or property damage.

Operation.................................................3

Maintenance...............................................5

DF3015 Exploded Parts Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

DF3015ReplacementPartsList ...............................7

DF3015 Wiring Diagram......................................8

DFB8842 Exploded Parts Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

DFB8842 Replacement Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

DFB8842WiringDiagram ...................................10

Front Glass Replacement....................................11

Partially Reective Glass Replacement .........................11

On/Off Switch and Remote Switchboard Replacement . . . . . . . . . . . . . 11

Flicker Motor/Flicker Rod Replacement .........................12

Lower Light Harness Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

RemoteControlReplacement................................14

Heater Assembly and Cutout Replacement ......................15

PowerCordReplacement ...................................16

Troubleshooting Guide ......................................18

Always use a qualied technician or service agency to repair this replace.

! Procedures and techniques that are considered important enough to emphasize.

 Procedures and techniques which, if not carefully followed, will result in damage to the

equipment.

 Procedures and techniques which, if not carefully followed, will expose the user to the

risk of re, serious injury, or death.





The manual controls for the replace are located in the lower

right hand corner (Figure 1).

 

Supplies power to the 3-Position Selector Switch.

B. 

 The unit is operated with the

remote control.

 The ame effect is turned on.

 The ame effect and

heater are turned on simultaneously. When the manual

control is in the position the heater does

not run on the remote control operated thermostat.

!When the 3-Position Selector Switch is in the

Flame and positions, the replace unit will

not operate with the remote control.

 

Used to synchronize the supplied remote control with the

replace.



Should the heater overheat, an automatic switch will turn the

heater off and it will not come back on without being reset.

The temperature cutoff switch can be reset by unplugging the

unit, waiting ve (5) minutes and plugging the unit back in.

 If you need to continuously reset the heater,

unplug the unit and call Dimplex North America Limited

at 1-888-346-7539. Please have your model and serial

number ready when calling.



The remote control has a range of approximately 50 feet

(15.25 m), it does not have to be pointed at the replace

and can pass through most obstacles (including walls). It

is supplied with 243 independent frequencies to prevent

interference with other units.



Depress tab on the battery cover on the back of the1.

remote control and remove battery cover.

Install/replace two (2) AAA batteries into the remote2.

control.

Ensure Child Lock is in the “unlocked” position (Figure 2).3.

Replace the battery cover.4.

!When the “BAT”symbol is present on the

remote control it is recommended to replace the batteries

promptly, to maintain full functionality of the remote/

replace. The remote control has a battery backup time of

only several hours.

Battery must be recycled or disposed of properly.

Check with your Local Authority or Retailer for

recycling advice in your area.



Plug cord into a 120 Volt wall outlet.1.

Ensure the On/Off Switch located in the switch box on2.

the replace in the lower right hand corner is in the On

position.

Set the Three Position Manual Control (Figure 1B) to the3.

position (right position).

Press and hold the Initialization Button on the unit4.

(Figure 1C).

While holding the Initialization Button, press the Flame/5.

Heat On/Off button or the Purire™ On/Off button on

the remote control.

Release the Initialization Button on the unit.6.

Press the Flame/Heat On/Off button7. to turn the Flame/

Heat function on or press the Purire™ On/Off button to

turn the Purire™ function on.

Figure 1 A

Figure 2

Batteries

Child Lock



(All letters are in reference to Figure 3)

 

Press Hbutton to turn replace on. Press Jto raise

thermostat, or Ito lower the thermostat. Press both Jand Ito

change °F to °C.

 

While the replace is running, repeatedly press the or K

button to increase or decrease the brightness of the upper

lights.

 

While the replace is running, press the button to increase

and  to maintain the desired set temperature.



If desired, depending on the season, the heater on the unit

can be disabled. The unit will operate in the same fashion,

with remainder of the controls.

To Disable - Press Jand O at the same time. The

temperature setting on the remote will no longer be

visible.

!The heat will not work in manual controls

either.

To Enable - Press Jand Q at the same time. The

temperature setting will now be visible again.

(Figure 4)

Depress tab on the1.

battery cover on the back

of the remote control

and remove the battery

cover.

Move Child Lock tab2.

to the right to lock the

remote control.

Move Child Lock tab back to the left to unlock the remote3.

control.

Replace the battery cover.4.

!To temporarily unlock the remote control press (in

order) I, then J, then K.

When the remote control’s backlight is illuminated the 

 is bypassed. When the backlight is off the 

is re-activated.



If the replace does not respond properly to the remote

control, the remote operating frequency may have to be

reset. The Remote Control can send another frequency code

to the Remote Control Receiver to eliminate interference.

Simultaneously press the1. Obutton and the Qbutton on

the remote control.

“2. COD” will appear in place of the sleep timer digits.

Release the3. Obutton and the Qbutton.

Press and hold the Initialization button on the unit (Figure4.

3C).

Press the5. Hbutton on the remote control.

Your remote control will now have a different frequency

communicating with the replace.

Figure 4

Unlocked Locked

Child Lock Tab



 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

P. Sleep Timer Up

 

 

the speed of the ame or press Mto decrease the speed of

the ame.

 

The Sleep Timer automatically shuts off the replace after a

preset time (from 30 minutes to 8 hours).

During replace operation, to set the sleep timer press the

Pbutton. Set the timer from 30 minutes through 8 hours.

The replace will automatically turn off when the sleep timer

reaches zero (0) minutes.

The sleep timer can be cancelled at any time by pressing the

Obutton repeatedly until the sleep timer displays nothing.

 

Press the button to turn the Purire™ function on. When

the Purire™ function is on, the Purire™ symbol will ash.

When off, the symbol will be solid.

The default setting for the Purire™ is set at low speed.

Press the Q or the buttons to change between low and

high speeds. Press the  button to turn the Purire™

function off.

 

Press the Hbutton to turn the Flame/Heat function on.

When Bis higher than Athe heat will come on. To turn the

heat off, lower Bso that it’s setting is lower than A. The

default temperature setting is 72°F (22°C).

!When using the remote control the heater runs

on a thermostat. Press the J or I buttons to adjust the

set temperature. Once the desired set temperature is

reached the heater will turn off. The heater will cycle 

Disconnect power before attempting any

maintenance or cleaning to reduce the risk of re, electric

shock or damage to persons.



 Allow at least ve (5) minutes for light

bulbs and heater to cool off before touching bulbs to avoid

accidental burning of skin.

Light bulbs need to be replaced when you notice a dark

section of the ame. There are three (3) under the Log Set,

which generate the ames and embers, and two (2) bulbs

above the log that illuminate the log exterior.



It is a good idea to replace all light bulbs at one time if they

are close to the end of their rated life. Group replacement

will reduce the number of times you need to open the unit to

replace light bulbs. Care must be taken when removing the

Log Set as the Log Set contains LED’s and wires.



Quantity of three (3) clear chandelier or candelabra bulbs

with an E-12 (small) socket base, 60 Watt rating. Example:

GE 60BC or Philips 60CTC.

D



Slide replace out of mantel.1.

Remove four (4) Phillips screws from right side of trim2.

(Figure 5).

Remove trim.3.

Slide glass to right side of replace to remove (Figure 5).4.

Pull the front edge of the plastic Log Set or plastic grate5.

up and forward until the rear tab releases from the ledge

located at the bottom of the Partially Reective Glass

(Figure 6).

!Only handle the Log Set Assembly by the

Ember Bed or plastic grate.

!Log Set Assembly ts tightly into rebox, some

force may be necessary to remove.

Set Log Set Assembly in front of replace.6.

Unscrew bulbs counter clockwise.7.

Insert new bulbs and screw in clockwise.8.

Install the Log Set Assembly by placing the front, bottom9.

edge of the Ember Bed in the track behind the control

panel. Once in place, push down on the back edge of the

Ember Bed until the rear tab snaps into place under the

Partially Reective Glass (Figure 6).

!Ensure the Log Set Assembly is installed tightly

under the back ledge to prevent light leakage.

Slide front glass back into position and attach trim.10.



Quantity of two (2) clear chandelier or candelabra bulbs with

an E-12 (small) socket base, 15 Watt rating.





Slide replace out of mantel.1.

Remove four (4) Phillips screws from right side of trim2.

(Figure 5).

Remove trim.3.

Slide glass to the right side of the replace to remove 4.

(Figure 5).

Remove Upper Light Bracket (Figure 5).5.

Upper bulbs are located in the upper left and upper right6.

corners of the replace.

Unscrew bulbs counter clockwise.7.

Insert new bulbs and screw in clockwise.8.

Re-install Upper Light Bracket.9.

Slide front glass back into position and attach trim.10.



Trim

Front Glass

Log Set Assembly

Figure 5

Upper Light

Bracket

Lower Bulbs

Upper Bulbs

Back

Ledge

Log

Ember Bed

Rear

Tab

Front

Edge

Side Section





The Purire™ lter supplied in your replace is reusable

and washable. The lter should be cleaned or replaced

on average once a year. To clean the lter gently tap lter

on a hard surface to dislodge any loose dirt or debris, and

then clean with water. No soap or cleaning products are

recommended. The lter size is 20 x 10 x 1 inches, rated at

MERV 10.



Remove replace from mantel.1.

Filter can be accessed from the top rear of the unit2.

(Figure 7).

Grasp lter and slide lter straight up.3.

Replace or clean lter.4.

!If after market air lter is used ensure it is

installed according to the manufacturer’s recommended

instructions.



The glass is cleaned in the factory during the assembly

operation. During shipment, installation, handling, etc., the

clear door may collect dust particles, these can be removed

by dusting lightly with a clean dry cloth.

To remove ngerprints or other marks, the clear door can be

cleaned with a damp cloth. The clear door should be com-

pletely dried with a lint free cloth to prevent water spots. To

prevent scratching, do not use abrasive cleaners or spray

liquids on the clear door surface.

Fireplace Surface Cleaning

Use damp warm cloth only to clean painted surfaces. Do

not use abrasive cleaners on glass surface or spray liquids

directly onto any surface.

Figure 7

Purire™

Filter





1. Log Set Assembly ..................0439070100RP

2. Flicker Motor . . . . . . . . . . . . . . . . . . . . . 3000240200KIT

3. Heater Assembly ..................2200490600RP

4. Cutout ...........................2300270300RP

5. On/Off Switch .....................2800070700RP

6. Remote Switchboard . . . . . . . . . . . . . . . 3000300300RP

7. Power Cord . . . . . . . . . . . . . . . . . . . . . . 4100040500RP

8. Lower Light Harness (outer pair) . . . . . . 2500400100RP

9. Upper Light Harness . . . . . . . . . . . . . . . 2500400200RP

10. Partially Reective Glass ............5900680100RP

11. Front Glass . . . . . . . . . . . . . . . . . . . . . . 5900310400RP

12. Remote Control

433MHz (Silver Dimplex Logo) ........3000300100RP

2.4GHz (Red Dimplex Logo)..........3000890100RP

13. Remote Control Receiver

433MHz (Silver) . . . . . . . . . . . . . . . . . . . 3000300200RP

2.4GHz (Red) . . . . . . . . . . . . . . . . . . . . . 3000880100RP

14. Flicker Rod .......................5900080700RP

15. Purire™ Filter ....................0439060100RP

16. Switch Housing Door . . . . . . . . . . . . . . . 0439210000RP

17. Lower Light Socket (center) . . . . . . . . . . 2500150200RP

18. Fireplace Foot .....................8800090100RP

LOWER LIGHT

HARNESS

LOWER LIGHT

HARNESS UPPER LIGHT

HARNESS

THERMAL

CUTOUT

LOW SPEED

MOTOR WINDING

HIGH SPEED

MOTOR WINDING

RECIEVER

PCB

FLAME

STEPPER MOTOR

LEDS

LOG 1

LEDS

LOG 3

LEDS

LOG 4

LEDS

LOG 5

LEDS

LOG 2

0439070100

LOGSET AND LED HARNESS

2500380200

JP7

3000240400

2500150200

2500400100

JP9

PIN 5

JP16 NEUTRAL

2500400200

PIN 4

PIN 6

PIN 3

PIN 2

PIN 1

JP11

2200490600

84132004QT

2500390100

PIN 4

PIN 2

PIN 1

PIN 3

2300200500

4100040200

JP15

3000300200

JP12

JP7

JP9

ELEMENT 1

JP15

JP16

JP13

ELEMENT 2

JP11

JP7

JP15

JP9

JP11

JP12

A LIVE

JP13

84141030FF

A B

JP16

JP13

NEUTRAL

LINE IN

84141036CF

2800070700

Cord Set

Heater

Assembly

On/Off

Switch

Remote Control

Receiver (433 MHz)

Flicker Motor

DF3015 Wiring Diagram

JP2

HIGH SPEED

MOTOR WINDING

LOW SPEED

MOTOR WINDING

UPPER LIGHT

HARNESS

LOWER LIGHT

HARNESS

LOWER LIGHT

HARNESS

THERMAL

CUTOUT

RECIEVER

PCB

FLAME

STEPPER MOTOR

LEDS

LOG 1

LEDS

LOG 3

LEDS

LOG 4

LEDS

LOG 5

LEDS

LOG 2

3000880100

JP6

JP3

JP5

JP4

JP10

JP9

JP7

2800070700

84141036CF

ALINE IN

NEUTRAL

JP7

JP10

84141030FF

JP7

A LIVE

JP4

JP6

JP9

JP3

JP5

ELEMENT 2

ELEMENT 1

JP9

4100040200

2300200500

PIN 3

PIN 1

PIN 2

PIN 4

2500390100

84132004QT

EL1

2200490600

JP5

PIN 1

PIN 2

PIN 3

PIN 6

PIN 4

2500400200

JP10 NEUTRAL

PIN 5

JP6

2500400100

2500150200

3000240400

JP3

2500380200

LOGSET AND LED HARNESS

0439070100

Heater

Assembly

On/Off

Switch

Remote Control

Receiver (2.4GHz)

Flicker Motor

Cord Set





Log Set Assembly1. ..................0438550100RP

Flicker Motor2. . . . . . . . . . . . . . . . . . . . . . 3000240200KIT

Heater Assembly3. ..................2200490600RP

Cutout4. ...........................2300270300RP

On/Off Switch5. .....................2800070700RP

Remote Switchboard6. . . . . . . . . . . . . . . . 3000300300RP

Power Cord7. . . . . . . . . . . . . . . . . . . . . . . 4100040500RP

Lower Light Harness (Outer Pair)8. ......2500400100RP

Upper Light Harness9. . . . . . . . . . . . . . . . 2500400200RP

Partially Reective Glass 10. ............5900680100RP

Front Glass11. . . . . . . . . . . . . . . . . . . . . . . 5900310500RP

Remote Control12.

433MHz (Silver Dimplex Logo) ........3000300100RP

2.4GHz (Red Dimplex Logo)..........3000890100RP

Remote Control Receiver13.

433MHz (Silver) . . . . . . . . . . . . . . . . . . . 3000300200RP

2.4GHz (Red) . . . . . . . . . . . . . . . . . . . . . 3000880100RP

Flicker Rod14. .......................5900080700RP

Purire™ Filter15. . . . . . . . . . . . . . . . . . . . . 0439060100RP

Switch Housing Door16. . . . . . . . . . . . . . . . 0439210000RP

Lower Light Socket (Center)17. ..........2500150200RP

Fireplace Foot18. .....................8800090100RP

LED Log Set Wire Harness19. ...........2500380200RP

Heater Assembly Wire Harness20. . . . . . . . 2500390100RP

DFB8842 Wiring Diagram

Cord Set

Heater

Assembly

On/Off

Switch

Remote Control

Receiver (433 MHz)

Flicker Motor

Heater

Assembly

On/Off

Switch

Remote Control

Receiver (2.4GHz)

Flicker Motor

Cord Set

Other manuals for MULTIFIRE DF3015

This manual suits for next models

Table of contents

Other Dimplex Indoor Fireplace manuals

Dimplex

Dimplex 314 CHE User manual

Dimplex

Dimplex Nicole User manual

Dimplex

Dimplex XHD23L User manual

Dimplex

Dimplex BF33ST User manual

Dimplex

Dimplex SIL48M User manual

Dimplex

Dimplex BLF74 User manual

Dimplex

Dimplex EWF-SS User manual

Dimplex

Dimplex RLG20BR User manual

Dimplex

Dimplex Montclair User manual

Dimplex

Dimplex PF2325CG User manual

Dimplex

Dimplex DF3003 User manual

Dimplex

Dimplex DF2608-EU User manual

Dimplex

Dimplex OLF46-AM User manual

Dimplex

Dimplex BLF50 User manual

Dimplex

Dimplex BF 30' series Operation manual

Dimplex

Dimplex Brayford BFD20E Instruction Manual

Dimplex

Dimplex DF1135M User manual

Dimplex

Dimplex LAGsu User manual

Dimplex

Dimplex ELECTRALOG DF203A User manual

Dimplex

Dimplex Albany Optimyst ABN15-RGB-EU Instruction Manual

Dimplex

Dimplex ENGDL20 S E User manual

Dimplex

Dimplex DWF36-PG User manual

Dimplex

Dimplex OPTIMYST CAS400L User manual

Dimplex

Dimplex LIBERTY SUITE LBY15-AU User manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual