Dimplex BOF4056 User manual
Owner’s Manual
Model
BOF4056
BOF4068
BOF6056
7213470100R01
IMPORTANT SAFETY INFORMATION: Always read this manual
rst before attempting to install or use the wall mount engine. For
your safety, always comply with all warnings and safety instructions
contained in this manual to prevent personal injury or property
damage.
To view the full line of Dimplex products, please visit
www.dimplex.com
2 www.dimplex.com
Table of Contents
Always use a qualied technician
or service agency to repair
this engine.
!NOTE: Procedures and
techniques that are considered
important enough to
emphasize.
CAUTION: Procedures and
techniques which, if not
carefully followed, will result in
damage to the equipment.
WARNING: Procedures
and techniques which, if not
carefully followed, will expose
the user to the risk of re,
serious injury, or death.
Welcome & Congratulations ....................3
IMPORTANT INSTRUCTIONS ..................4
Installation ..................................6
Assembly ..................................10
Operation ..................................12
Maintenance ...............................15
Warranty .................................17
Replacement Parts ..........................19
3
Welcome & Congratulations
Thank you and congratulations for choosing to purchase an Optimyst®
Pro engine from Dimplex, the world leader in electric replaces.
Please carefully read and save these instructions.
CAUTION: Read all instructions and warnings carefully before
starting installation. Failure to follow these instructions may result in a
possible electric shock, re hazard and will void the warranty.
Please record your model and serial numbers below for future
reference: model and serial numbers can be found on the Model and
Serial Number Label of your wall mount engine.
NO NEED TO RETURN TO THE STORE
Questions with operation or assembly? Require Parts Information?
Product Under Manufacturer’s Warranty?
Contact us at: www.dimplex.com/customer_support
For Troubleshooting and Technical Support
OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)
Monday to Friday 8:00 a.m. to 4:30 p.m. EST
Please have your model number and product serial
number ready. (See above)
Model Number
Serial Number
4 www.dimplex.com
When using electrical appliances,
basic precautions should always
be followed to reduce the risk of
fire, electric shock, and injury to
persons, including the following:
① Read all instructions before
using the engine.
②
The heater is hot when in use.
To avoid burns, do not let bare skin
touch hot surfaces. The trim around
the heater outlet becomes hot dur-
ing heater operation.
DANGER:
High temperatures
may be generated under certain ab-
normal conditions. Do not partially
of fully cover the front of this heater.
③
Extreme caution is necessary
when any heater is used by or near
children or invalids and whenever
the unit is left operating and unat-
tended.
④ Always unplug the engine
when not in use.
⑤ Do not operate any unit with
a damaged cord or plug, or if
the engine has been dropped or
damaged in any manner. Contact
Dimplex Technical Service at
1-888-346-7539.
⑥ Do not use outdoors.
IMPORTANT INSTRUCTIONS
⑦ Never locate unit where it may
fall into a bathtub or other water
container.
⑧ To disconnect the unit, turn
the controls off, then remove the
plug from the outlet or disconnect
power at the service panel.
⑨ Always use properly grounded,
fused and polarized outlets.
⑩
Do not insert or allow foreign
objects to enter any ventilation or
exhaust opening as this may cause
an electric shock or re, or damage
to the heater.
⑪
To prevent a possible re, do not
block air intake or exhaust in any
manner. Do not use on soft surfac-
es, like a bed, where openings may
become blocked.
⑫
All electrical heaters have hot
and arching or sparking parts inside.
Do not use in areas where gasoline,
paint, or ammable liquids are used
or stored or where the unit will be
exposed to ammable vapors.
⑬ Do not modify the engine.
Use it only as described in this
manual. Any other use not recom-
mended by the manufacturer may
cause re, electric shock or injury
to persons.
5
SAVE THESE INSTRUCTIONS
⑭
To reduce the risk of electric
shock, this appliance must be
grounded. Avoid the use of an ex-
tension cord. Extension cords may
overheat and cause a risk of re.
Always plug heaters directly into a
wall outlet/receptacle. Never use
with an extension cord or relocat-
able power tap (outlet/power strip).
⑮ Do not burn wood or other
materials in the engine.
⑯ Always use a certied electri-
cian should new circuits or outlets
be required.
⑰ Disconnect the power supply
before performing any cleaning,
maintenance or relocation of the
unit.
⑱ When transporting or stor-
ing the unit and cord, keep in a
dry place, free from excessive
vibration and store so as to avoid
damage.
⑲
The wall mount engine must
not be located directly below a
socket outlet.
⑳ The wall mount engine must
be positioned so that the plug is
accessible.
WARNING: Remote control
contains small batteries. Keep
away from children. If swallowed,
seek medical attention immedi-
ately.
WARNING: Do not install bat-
tery backwards, charge, put in re
or mix with used or other battery
types - may explode or leak caus-
ing injury.
!NOTE: Changes or modica-
tions not expressly approved by
the party responsible for compli-
ance could void user's authority to
operate the equipment.
IMPORTANT INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
NO USER-SERVICEABLE PARTS INSIDE
6 www.dimplex.com
Installation
The Optimyst Pro is supplied
in an assembled state and is
designed to be permanently in-
stalled. The unit comes ready for
hardwire installation.
WARNING: Construction and
electrical outlet wiring must
comply with local building
codes and other applicable
regulations to reduce the risk
of re, electric shock and injury
to persons.
WARNING: To reduce the
risk of re, do not store or use
gasoline or other ammable
vapors or liquids in the vicinity
of the heater.
!NOTE: A 15 Amp, 120 Volt cir-
cuit is required. A dedicated circuit
is preferred but not essential in all
cases. A dedicated circuit will be
required if, after installation, the
circuit breaker trips or the fuse
blows on a regular basis when the
heater is operating. Additional ap-
pliances on the same circuit may
exceed the current rating of the
circuit breaker.
WARNING: Failure to install
the replace as instructed
below may result in damage
to the equipment and or may
expose the user to the risk of
re, serious injury, illness or
death.
WARNING: Do not attempt to
wire your own new outlets or
circuits. To reduce the risk of
re, electric shock or injury to
persons, always use a li-
censed electrician.
WARNING: Ensure that the
On/Off switch is set to the Off
position (refer to Operation
section) and that the circuit
on which the replace is to be
installed has the power cut off
at the service panel until instal-
lation is complete.
!NOTE: Please read all instruc-
tions before installing.
1. For rough in framing, the
opening should follow the
recommended dimensions
located in Figure 1.
!NOTE: Dimensions provided
are minimum clearances and will
vary depending on type of support
framing and nishing options.
!NOTE: It is recommended
that the bottom of the unit not be
mounted higher than 40 in. (1020
mm) from the ground to maintain
an optimized viewing angle of the
ame (Figure 2).
7
Installation
Figure 1
!NOTE: If installation in a cus-
tom mantel is desired, a power
cord accessory is available (BOF-
PLUGKIT) to plug the unit directly
into a wall outlet.
2. Allow up to 4 ft. (121.9 cm)
of service cable for connect-
ing a power supply wire to the
cable clamp on replace when
installing before nishing wall.
CAUTION: Use two conduc-
tor, non-metallic sheath cable
with ground wire (3 wires total)
for the incoming power supply on
replace inserts. Use appropriate
wire to meet local and national
electrical codes for rated power.
!NOTE: It is recommended that
all drywall installation and nish-
ing be completed after unit is fully
installed.
3. On the back of the unit remove
the cable clamp, by removing
the screw at the top (Figure 2).
4. Install a 3/8 in. (10 mm) or
1/2 in. (13 mm) cable connec-
tor, not included, suitable for
mounting in a 7/8 in. (22 mm)
hole, to the cable plate and
A
B
C
DE
A B C D E
BOF4056 17.8in (451mm) 27.6in. (701mm) 10.0in. (255mm) 16.3in (413mm) 15.6in. (395mm)
BOF4068 17.8in (451mm) 32.4in. (823mm) 10.0in. (255mm) 16.3in (413mm) 20.4in. (517mm)
BOF6056 23.9in. (607mm) 27.6in. (701mm) 10.0in. (255mm) 22.4in (569mm) 15.6in. (395mm)
8 www.dimplex.com
Installation
feed the supply cable through
the connector and secure.
5. Remove the 3 wires from
within the unit.
6. Connect the black wire (live)
from the unit to the black wire
from power supply.
7. Connect the white wire (neu-
tral) from the unit to the white
wire from power supply.
8. Connect the green wire
(ground) from the unit to the
green wire from power supply.
9. Place all connectors inside
the unit and secure the cable
clamp to unit. Ensure that the
cable clamp grips only the
jacket of service cable.
!NOTE: Once the unit has been
fully installed there is an access
Figure 3
panel in the water reservoir cavity
where the wiring can be accessed
from the front following installation
(Figure 3).
10. Install the unit into the roughed
in framing.
CAUTION: When inserting
the unit take care not to damage
or pinch any of the power cables
that are concealed in the wall.
WARNING: Ensure the power
wiring is not installed so that it
is pinched or against a sharp
edge and ensure that the pow-
er wiring is stored or secured
to avoid tripping or snagging to
reduce the risk of re, electric
shock or injury to persons.
11. Secure the unit to the framing
through the side anges with
the provided 8 screws (Figure
3).
Side
Flanges
Trim
Figure 2
Cable Plate
9
?
?
>88cm2
?
?
>88cm2
>14 in2
(>88 cm2)
>14 in2
(>88 cm2)
>14 in2
(>88 cm2)
Wiring
Figure 4
Installation
12. Reinstall the dust panel that
came installed in the rebox
opening.
13. Finish surrounding wall. There
are 3 different options for n-
ishing the wall:
CAUTION: Do not remove the
trim around the opening of the
unit (Figure 3).
• Permanent- install drywall
right up to the ange that sur-
rounds the opening (Figure 4).
!NOTE: An air inlet that is a
minimum of 14 in2 (88 cm2) is
required for optimum mist produc-
tion, for minimum dimensions
(Figure 4).
• SemiPermanent- nish
around edge using ashing
material (not included).
• Flexible- create opening big
enough to access mounting
anges and a false front that
can be removed.
Bathroom Installation
This rebox must be protected
by a GFI circuit. If a receptacle
is used it must be readily acces-
sible.
To prevent electrical shock this
unit is an electrical appliance
that is not watertight and must be
installed as to prevent water from
entering the unit. This unit must
be installed away from showers,
tubs, etc. Never locate replace
where it may fall into a bathtub or
other water containers. Keep tow-
els and other combustible materi-
als 3 feet (0.9 m) away from the
front of the unit.
10 www.dimplex.com
Log
Media
Removable Rell
Container
Light
Bulbs
Assembly
Figure 5
1. Carefully unpack all of the
components from the box.
(Figure 5)
2. Remove top cover by turning
the retaining tabs on both
ends of the water reservoir.
(Figure 6)
3. Install the light bulbs by
aligning the pins on the bulbs
and the xture and pressing
down until they are fully
inserted. (Figure 7)
4. Install the transducer so that
it is sitting level in the circular
holding area in the reservoir.
!NOTE: The transducer is
packed in the water reservoir and
wrapped to protect it during ship-
ping.
5. Orient transducer wire so that
it does not sit directly above
the emitter and the wire
passes through the slot in the
side of the tank. (Figure 6)
6. Reinstall the top cover and
ensure both retaining tabs
have been turned so that they
are pointing inwards.
7. Fill and install the Rell
Container.
!NOTE: Normal tap water can
be used in the Optimyst® as long
as the tap water is not considered
to be hard water. In the event
Top
Cover
Figure 6
Transducer
Emitter
Wire Slot
Remote
Control
Retaining
Tabs
Water
Reservoir
Other manuals for BOF4056
1
This manual suits for next models
2
Table of contents
Other Dimplex Indoor Fireplace manuals
Dimplex
Dimplex BFSL33 User manual
Dimplex
Dimplex DWF1215B User manual
Dimplex
Dimplex BFL50-EU User manual
Dimplex
Dimplex OPTIMYST RTOPCS20 User manual
Dimplex
Dimplex ENGDL20 S E User manual
Dimplex
Dimplex DF2690 User manual
Dimplex
Dimplex SIL48M User manual
Dimplex
Dimplex DF2603 User manual
Dimplex
Dimplex DWF3651 User manual
Dimplex
Dimplex BLF50 User manual
Dimplex
Dimplex ASP20 User manual
Dimplex
Dimplex DS5629 User manual
Dimplex
Dimplex DFB4047 User manual
Dimplex
Dimplex OptiMyst CAS400NHLL User manual
Dimplex
Dimplex 6908760100 User manual
Dimplex
Dimplex DIMPLEX ELECTRIC FIREPLACE User manual
Dimplex
Dimplex BF9000 User manual
Dimplex
Dimplex Bach User manual
Dimplex
Dimplex Mozart CFP3811GB User manual
Dimplex
Dimplex Adagio User manual
Popular Indoor Fireplace manuals by other brands
Brigantia
Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual
Nordpeis
Nordpeis Bergen Installation and user manual
Superior
Superior BCT2536TMN Installation and operation instructions
Quadra-Fire
Quadra-Fire 5100I-GD-B owner's manual
Renaissance
Renaissance RUMFORD 1000 user manual
Lacunza
Lacunza IV-800 Instruction book
Baxi
Baxi 940 Installer and owner guide
Dru
Dru Maestro 60/2 Tall RCH installation manual
Diamond Fireglass
Diamond Fireglass SS-O22 General assembly, installation, and operation instructions
HearthStone
HearthStone Windsor Bay 8830 Owner's manual and installation guide
Napoleon
Napoleon ASCENT B42 quick start guide
Enviro
Enviro E33GI owner's manual
Smeg
Smeg L30 FABE Installation & user's instructions
KEDDY
KEDDY K700 Installation instructions care and firing instructions
Godin
Godin 3451 manual
Jøtul
Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions
Austro Flamm
Austro Flamm Heidi Back 2.0 945048 operating manual
Desa
Desa CCFPDFT Owner's operating & installation manual