Dimplex LAGUNA LAGFB2 User manual

LAGUNA FIREBOX

LAGFB2

08/51849/0 ISS1

QUICK REFERENCE GUIDE

1. Prior to the ﬁrst use of the ﬁrebox verify the following:

• Are the circuit breakers for the ﬁrebox on?

• Are the light bulbs in your ﬁrebox loose? (to check, follow the instructions

for replacing the light bulbs under the Maintenance section of this manual)

• Is the ﬁrebox switched on?

2. The heater on your ﬁrebox may emit a slight, harmless odor when ﬁrst used.

This odor is a normal condition caused by the initial heating of internal heater

parts and will not occur again, if required ventilate the room.

3. If your heater does not emit heat, ensure the main switch is on, the built-in

thermostat is set to maximum to begin with,and any wall switches for the

unit are on. If this does not work, switch the unit off for 5 minutes and

try again. Consult the Operation section of your practical users guide for

further information.

4. The information regarding the model of your ﬁrebox can be found on the

rating plate located on the side adjacent to the supply cord.

5. If you have any technical questions regarding the operation of your ﬁreplace,

or require service for your ﬁreplace, please go to www.dimplex.co.uk and click

on “Customer Support” or e-mail us at [email protected]. Alternatively,

ring our contact centre on 0844 879 3588 (UK only). This is a Lo-call no. from BT

landline - other providers including mobile phones may charge you more.

For ROI customers please phone 01 842 4833.

CONTENTS

PAGE 1 Important Instructions

PAGE 2 Model Number Information

PAGE 3 Site Selection and Preparation

PAGE 3 Fireplace Installation

PAGE 4 Operation

PAGE 6 Maintenance

PAGE 8 After Sales Service

IMPORTANT INSTRUCTIONS

PLEASE RETAIN THIS USER’S GUIDE FOR FUTURE REFERENCE

When using electrical appliances, basic precautions should always be followed to reduce the risk of ﬁre,

electric shock, and injury to persons, including the following:

1. Read all instructions before using the electric ﬁrebox.

2. This ﬁrebox is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. The trim

around the heater outlet becomes hot during heater operation. Keep combustible materials, such as

furniture, pillows, bedding, papers, clothes, and curtains at least 0.9m from the front and side of the

unit.

3. Extreme caution is necessary when any heater is used by or near children or invalids and whenever

the unit is left operating and unattended. For additional safety purchase a suitable ﬁreguard.

4. Young children should be supervised to ensure that they do not play with the appliance.

5. The appliance is not intended for use by persons(including children) with reduced physical sensory or

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning the use of the appliance by a person responsible for their safety.

6. The appliance must be positioned so that the plug is accessible.

7. Always unplug the electric ﬁrebox when not in use.

8. If the supply cord is damaged, it must be replaced by the manufacturer, or its service agent, or a

qualiﬁed person in order to avoid a hazard.

9. Do not operate any unit with a damaged cord or plug, or if the heater has malfunctioned, or if the

electric ﬁrebox has been dropped or damaged in any manner. Return heater to authorized service

facility for examination, electrical or mechanical adjustment, or repair.

10. Do not use outdoors

11. Do not use this ﬁrebox in the immediate surroundings of a bath, a shower or a swimming pool.

12. Do not install the ﬁrebox directly on carpet or a similar surface which may restrict air circulation

beneath the unit.

13. Do not run the cord under carpeting. DO NOT COVER cord with throw rugs, runners, or the like.

Arrange cord away from trafﬁc area and where it will not be tripped over.

14. Do not locate the heater immediately below a ﬁxed socket-outlet.

15. To disconnect the ﬁrebox, turn the controls off, then remove the plug from the outlet.

16. Do not insert or allow foreign objects to enter any ventilation or outlet opening as this may cause an

electric shock or ﬁre, or damage to the heater.

17. To prevent a possible ﬁre, do not block air intake or outlet in any manner. Do not use on soft

surfaces, like a bed, where openings may become blocked.

18. Do not modify the electric ﬁrebox. Use it only as described in this manual. Any other use not

recommended by the manufacturer may cause ﬁre, electric shock or injury to persons.

19. Avoid the use of an extension cord. Extension cords may overheat and cause a risk of ﬁre.

20. Do not burn wood or other materials in the electric ﬁrebox.

21. Do not strike the ﬁrebox glass.

22. Always use a certiﬁed electrician should new circuits or outlets be required working to the current

addition of wiring regulations.

23. Always use properly grounded, and fused outlets.

24. Disconnect all power supply before performing any cleaning, maintenance or relocation of the unit.

25. When transporting or storing the unit and cord, keep in a dry place, free from excessive vibration and

store so as to avoid damage.

26. WARNING: In order to avoid overheating, DO NOT COVER the heater.

PLEASE SAVE THESE INSTRUCTIONS.

NOTE: Procedures and techniques that are considered important enough to emphasize.

CAUTION: Procedures and techniques which, if not carefully followed, will result in damage to the

equipment.

WARNING: Procedures and techniques which, if not carefully followed, will expose the user to the risk of

ﬁre or serious injury.

MODEL AND SERIAL NUMBER INFORMATION

If you have any questions about our products please have the product model number available upon

calling customer service. To locate the model number label see below.(FIGURE 1)

FIGURE 1

Firebox

Model

Number

Label

NOTE

A 13amp, 230VAC circuit is required. A dedicated circuit is preferred but not essential in all cases. A

dedicated circuit will be required if, after installation, the circuit breaker trips or the fuse blows on a regular

basis when the heater is operating. Additional appliances on the same circuit may exceed the current

rating of the circuit breaker.

WARNING

Ensure the power cord is not installed so that it is pinched or against a sharp edge and ensure that the

power cord is stored or secured to avoid tripping or snagging to reduce the risk of ﬁre, electric shock or

injury to persons.

Construction and electrical outlet wiring must comply with local building codes and other applicable

regulations to reduce the risk of ﬁre, electric shock and injury to persons.

Do not attempt to wire your own new outlets or circuits. To reduce the risk of ﬁre, electric shock or injury

to persons, always use a qualiﬁed electrician.

SITE SELECTION AND PREPARATION

This section provides instructions for selecting a location and preparing the site to install the ﬁrebox into

your Dimplex mantel surround.

1. Select a suitable location that is not susceptible to moisture and is away from drapes, furniture

and high trafﬁc.

2. For ease of electrical hook up you may wish to locate the ﬁrebox near an existing outlet (refer

to NOTE).

3. Store the ﬁrebox in a safe dry and dust free location.

NOTE

The dimensions of the ﬁrebox are 768mm wide X 648mm high X 267mm deep. The viewing area is

765mm wide and 511mm high. The ﬁrebox does not require any additional venting.

FIREBOX INSTALLATION

1. INSTALL THE FIREBOX ASSEMBLY INTO A MANTEL (refer to mantel assembly instructions).

Please take care when placing ﬁrebox in mantel (2 person lift)

IMPORTANT

If not using a Dimplex mantel, the ﬁrebox must be installed in an enclosure with the following

MINIMUM internal/opening dimensions. (FIGURE 2)

FIGURE 2

658mm

775mm

300mm

2. NEW WALL CONSTRUCTION

1. Select a suitable location that is not susceptible to moisture and is away from drapes,

furniture and high trafﬁc.

2. Place the ﬁrebox in the desired location to see how it will look in the room.

3. Mark the desired location on the ﬂoor and store the ﬁrebox in a safe, dry and dust free

location.

4. Use studs to frame an opening of 775mm wide X 658mm high X 300mm deep.

The power cord can be routed from behind the trim and along the wall to an outlet

near the ﬁreplace. Please make sure the cord is not routed across the top of the ﬁrebox.

CAUTION

Clearance for air circulation beneath the ﬁrebox insert is provided by three rubber feet.

DO NOT INSTALL THE FIREBOX INSERT DIRECTLY ON CARPET OR SIMILAR SURFACES WHICH

MAY RESTRICT AIR CIRCULATION. If installing the ﬁrebox in a carpeted area, place a one-piece, solid,

ﬂat surface under the ﬁrebox insert. Ensure that all three of the insert’s feet rest securely on this surface.

OPERATION REMOTE CONTROL

The remote control has a range of approximately 15 meters.

REMOTE CONTROL INITIALIZATION

This procedure may be required if there is a loss of power to the remote

control in the ﬁrebox (i.e. power failure, breaker tripped, main power switch is

turned off, remote battery failure) or if a new remote is used.

1. Ensure that power is supplied through main service panel.

2. Locate manual controls. (FIGURE 4)

3. Activate main power switch.

4. Press — (ON) button located on the Manual Selection Control

for 3 seconds (FIGURE 5). All 3 indicators will ﬂash.

5. Press the ON button on the transmitter (FIGURE 3). The

indicators will ﬂash rapidly and then turn off.

This will synchronize the remote control transmitter and receiver.

REMOTE CONTROL USAGE

The remote control operates the ﬁrebox levels sequentially. The level is

increased every time the ON button on the transmitter is pressed. The ﬁrebox

can be turned off at any point by pressing the OFF button on the remote

control transmitter, or by switching off the mains switch.

FIGURE 3

FIGURE 4

Manual Controls Located

Under Door

FIGURE 5

Main Selector Switches

Indicator Lights Thermostat Control

Main Power Switch

Level 1: The ﬂame effect is turned on and the ﬁrst red indicator light is activated.

Level 2: The ﬂame effect remains on, and the PuriﬁreTM is activated. The ﬁrst and second red

indicator lights are activated.

Level 3: The ﬂame effect remains on, the heater is activated, and all three red indicator lights are

activated.

MANUAL CONTROLS

The ﬁreplace can also be controlled in a similar manner to the remote control with switches located on the

ﬁreplace (FIGURE 6).

A. On Switch

Operates ﬁreplace in the same manner as the remote control transmitter. Pressing this button has

the same effect as the ON button on the remote control. Pressing once to the activates Level 1, twice

activates Level 2, three times activates Level 3.

Level 1: The ﬂame effect is turned on and the ﬁrst red indicator light is activated.

Level 2: The ﬂame effect remains on, and the PuriﬁreTM is activated. The ﬁrst and second red

indicator lights are activated.

Level 3: The ﬂame effect remains on, the heater is activated, and all three red indicator lights are

activated.

B. Off Switch

Pressing this button has the same effect as the OFF button on the remote control. Pressing once will

shut the unit off.

FIGURE 6

B. OFF SwitchA. ON Switch

Level 2

Indicator

Level 3

Indicator

Level 1

Indicator

HEATER THERMOSTAT CONTROL

To adjust the temperature to your individual requirements, turn the thermostat control clockwise all the

way to turn on the heater. When the room reaches the desired temperature, turn the thermostat knob

counter clockwise until you hear a click. Leave in this position to maintain the room temperature at this

setting. For additional heat, turn clockwise until you hear the click again and the heater will turn on

NOTE

The heater may emit a slight harmless odor when ﬁrst used. This odor is a normal condition caused by

initial heating of internal parts and will not occur again.

THE TEMPERATURE CUTOUT SWITCH

The heater on this ﬁreplace is protected with a safety device to prevent overheating. Should the heater

overheat, an automatic cut out will turn the heater off. The heater will re-activate once the heater has

cooled. The overheat cutout may be triggered if the ﬁlter is dirty. Follow ﬁlter maintenance on Page 7.

CAUTION

If the heater continuously resets, disconnect the power at the main service panel and call your local

dealer.

MAINTENANCE

LIGHT BULB REPLACEMENT

Allow at least 5 minutes for light bulbs to cool before touching bulbs to avoid accidental burning of skin.

Light bulbs need to be replaced when you notice a dark section of the ﬂame or when the clarity and detail

of the log ember bed exterior disappears. There are four bulbs under the log set, which generate the

ﬂames and embers, and two bulbs above the log that illuminate the log exterior.

LOWER LIGHT BULB REQUIREMENTS

Quantity of 4 clear chandelier or candelabra bulbs

with an E-14 (small) socket base, 40 watt rating.

DO NOT EXCEED 40 WATTS PER BULB.

HELPFUL HINTS

It is a good idea to replace all light bulbs at one

time if they are close to the end of their rated life.

Group replacement will reduce the number of times

you need to open the unit to replace light bulbs.

Care must be taken when removing the logset as

the logset contains LED’s and wires.

TO ACCESS THE LOWER BULB AREA (FIGURE 7)

Please take care when placing ﬁrebox in mantel (2 person lift)

1. Slide ﬁrebox out of mantel 50-75mm.

2. Remove 4 Phillips screws from the right side of trim.

3. Slide glass to right side of ﬁrebox to remove.

4. Pull the front edge of the plastic ember bed or plastic

grate up and forward until the rear tab releases from

the ledge located at the bottom of the mirror.

IMPORTANT: Only handle the logset by the emberbed.

NOTE: Logset ﬁts tightly into ﬁrebox, so care is necessary

when removing.

5. Set logset in front of ﬁrebox.

6. Disconnect the logset LED wire harness from unit.

7. Unscrew bulbs counter clockwise.

8. Insert new bulbs.

9. Reconnect the logset LED wire harness.

10. Replace the logset by inserting the front edge of the ﬁrebox and push down on the rear edge of

the emberbed until it snaps into place. (FIGURE 8)

NOTE: Ensure the logset is installed tightly under the back ledge to prevent light leakage.

11. Slide front glass back into position and attach trim.

UPPER LIGHT BULB REQUIREMENTS

Quantity of 2 clear chandelier or candelabra bulbs with an E-14 (small) socket base, 7 watt rating.

DO NOT EXCEED 7 WATTS PER BULB

TO ACCESS THE UPPER LIGHT BULB AREA (FIGURE 7)

Please take care when placing ﬁrebox in mantel (2 person lift)

1. Slide ﬁrebox out of mantel 50-75mm.

2. Remove 4 Phillips screws from right side of trim.

3. Remove trim.

4. Slide glass to the right side of the ﬁrebox to remove.

5. Remove upper light panel.

6. Upper bulbs located in the upper left and upper right corners of ﬁrebox.

FIGURE 7

Upper Light

Panel Upper

Bulbs

Trim

Logset

Front

Glass

Lower

Bulbs

LED Wire

Harness

FIGURE 8

7. Unscrew bulbs counter clockwise.

8. Insert new bulbs.

9. Re-install upper light panel.

10. Slide front glass back into position and attach trim.

11. Re-insert the ﬁrebox. Please take care when placing ﬁrebox in mantel (2 person lift)

PURIFIRE™ FILTER

The Puriﬁre™ ﬁlter supplied in your ﬁrebox is reusable and washable. The ﬁlter should be cleaned or

replaced on average once a year. To clean the ﬁlter gently tap ﬁlter on a hard surface to dislodge any

loose dirt or debris, and then clean with water. No soap or cleaning products are recommended. The

ﬁlter size is 508mm x 254mm x 25mm (20inch X 10inch X 1inch) rated at MERV 10.

TO REPLACE FILTER (FIGURE 9)

1. Remove ﬁrebox from mantel.

Please take care when placing ﬁrebox in mantel (2 person lift)

2. Filter can be accessed from the top rear of the unit.

3. Grasp ﬁlter and slide ﬁlter straight up.

4. Replace or clean ﬁlter.

NOTE

If after market air ﬁlter is used ensure it is installed according to the manufacturers recommended

instructions.

FIGURE 9

Air Filter

Firebox

GLASS CLEANING

The glass is cleaned in the factory during the assembly operation. During shipment, installation, handling,

etc., the glass may collect dust particles. These can be removed by dusting lightly with a clean dry cloth.

To remove ﬁngerprints or other marks, the glass can be cleaned with a damp cloth. To prevent scratch-

ing, do not use abrasive cleaners or spray liquids on the glass surface.

FIREBOX SURFACE CLEANING

Use a cloth dampened with warm water only to clean painted surfaces of the electric ﬁrebox. Do not use

abrasive cleaners.

After Sales Service

Your product is guaranteed for one year from the date of purchase.

Within this period, we undertake to repair or exchange this product free of charge (excluding lamps or

batteries and subject to availibility) provided it has been installed and operated in accordance with these

instructions.

Your rights under this guarantee are additional to your statutory rights, which in turn are not affect by this

guarantee.

Should you require after sales service you should contact our customer services help desk on 0844 879

3588. It would assist us if you can quote the model number, series, date of purchase and the nature of the

fault at the time of your call. The customer services helpdesk will also be able to advise you should you

need to purchase any spares.

Please do not return any faullty product to us in the ﬁrst instance as this may result in loss or damge and

delay in providing you with a staisfactory service.

Please retain your receipt as proof of purchase.

*Light bulbs and batteries are not covered in the warranty.

SERVICE

Contact your local dealer for service or warranty information.

RECYCLING

For electrical products sold in the European Community.

At the end of the electrical product’s useful life it should not be disposed of with household waste.

Please recycle where facilities exist. Check with your Local Authority or retailer for recycling

advice in your country.

The product complies with the European Safety Standard EN60335-2-30 and the

European Standard for Electromagnetic Compatibility (EMC) EN55014, EN61000

and EN50366 which cover the essential requirements of EEC Directives 2006/95

and 2004/108.

Table of contents

Other Dimplex Indoor Fireplace manuals

Dimplex

Dimplex DFP6975O User manual

Dimplex

Dimplex DF2426GB User manual

Dimplex

Dimplex BFSL33 User manual

Dimplex

Dimplex Revillusion RLG20 EU User manual

Dimplex

Dimplex Revillusion Osbourne User manual

Dimplex

Dimplex Dakota DKT20 User manual

Dimplex

Dimplex DFR2651L User manual

Dimplex

Dimplex BF8000ST User manual

Dimplex

Dimplex OLF46-AM User manual

Dimplex

Dimplex BLF50 User manual

Dimplex

Dimplex SP16 User manual

Dimplex

Dimplex DFI23096A User manual

Dimplex

Dimplex BLF7451-EU User manual

Dimplex

Dimplex Shaftsbury SHA20 User manual

Dimplex

Dimplex CHERITON LED CHT20 User manual

Dimplex

Dimplex CAS400LNH-INT User manual

Dimplex

Dimplex Atherton ATH20 Instruction Manual

Dimplex

Dimplex DWOP20R User manual

Dimplex

Dimplex DF1136L User manual

Dimplex

Dimplex DWF-13XX User manual

Dimplex

Dimplex DF2608 User manual

Dimplex

Dimplex Brayford BFD20E Instruction Manual

Dimplex

Dimplex Opti-myst RTOPW20 E User manual

Dimplex

Dimplex SF55992-AU Quick start guide

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual