Dimplex Rectory REC20R User manual

665

540 375 540

665

375

THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE.

Dimensions

(millimetres)

Installation and Operating Instructions

08/18893/0 Issue 0

Please note: Used in an environment where background

noise is very low, it may be possible to hear the fan which

operates the flame effect. This is normal and should not

be a cause for concern.

Rectory Model: REC20R

Montana Model: MON20R

Important Safety Advice:

When using electrical appliances, Basic

precautions should always be followed to reduce

the risk of fire, electrical shock, and injury to

persons, including the following:

••

•If the appliance is damaged, check with the

supplier before installation and operation.

••

•Do not use outdoors.

••

•Do not use in the immediate surroundings of

a bath, shower or swimming pool.

••

•Do not locate the heater immediately below a

fixed socket outlet or connection box.

••

•Do not cover the heater. Do not place material

or garments on the heater, or obstruct the air

circulation around the heater, for instance by

curtains or furniture, as this could cause

overheating and a fire risk.

••

•Do not leave young children or the infirm

unsupervised in the vicinity of the heater.

••

•Do not use this heater in series with a thermal

control, a program controller, a timer or any

other device that switches on the heat

automatically, since a fire risk exists when the

heater is accidentally covered or displaced.

••

•Ensure that furniture, curtains or other

combustible material are positioned no closer

than 1 metre from the heater.

••

•In the event of a fault unplug the heater.

••

•Unplug the heater when not required for long

periods.

••

•Although this heater complies with safety

standards, we do not recommend its use on

deep pile carpets or on long hair type of rugs.

••

•The appliance must be positioned so that the

plug is accessible.

••

•If the supply cord is damaged it must be

replaced by the manufacturer or service agent

or a similarly qualified person in order to avoid

a hazard.

••

•Keep the supply cord away from the front of

the heater.

Introduction

These fires incorporate a flame effect, which can be used

with or without heating, so that the comforting effect may be

enjoyed at any time of the year. The flame effect is provided

by a low wattage motor and two 25 watt lamps. Using the

flame effect on its own, therefore, requires little electricity.

The manual controls are located behind the firebox door. The

remote control is packed separately in the carton. A Choice

of 1kw or 2kw thermostatically controlled heat output is pro-

vided by the fan heater, which is concealed beneath the unit.

These models are designed to be free standing and are nor-

mally positioned against a wall.

Electrical connection

WARNING – THIS APPLIANCE MUST BE EARTHED

This heater must be used on an AC ~ supply only and the

voltage marked on the heater must correspond to the supply

voltage. This heater is fitted with a rewirable plug incorporat-

ing a 13 amp fuse. In the event of replacing the fuse in the

plug supplied, a 13 amp fuse approved by ASTA to BS 1362

must be used. If any other type of plug is used, a 15 amp fuse

must be fitted in the plug, the adaptor, or at the distribution

board.

IMPORTANT : If the plug is not suitable for your socket, the

13 amp plug should be removed. Before wiring the appropri-

ate plug, please note that the wires in this mains lead are

coloured in accordance with the following code :

GREEN AND YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

Connect the GREEN AND YELLOW wire to the terminal

marked ‘E’ or by the earth symbol . Connect the BROWN/

RED wire to the terminal marked ‘L’. Connect the BLUE/

BLACK wire to the terminal marked ‘N’ .

Fig. 1

Rectory REC20R Montana MON20R

Operation

The controls are located behind the hinged ‘ash-pan’ flap (see

Fig. 2).

Connect the fire to your electricity supply.

Open ash-pan for

access to controls

Fig. 2

Note: When either the remote control or the manual controls

are used, the neon’s will come on for 3 seconds indicating the

relevant setting (see fig. 3).

neon’s for indicating the

operation level

Fig. 3

1. Slide open the battery cover on the back of the remote

control

2. Install three AAA batteries into the remote control (see

Fig. 4)

3. Replace the battery cover.

Battery information

Fig. 4

Batteries

Discard leaky batteries

Dispose of batteries in the proper manner according to Pro-

vincial and local regulations. Any battery may leak electrolyte

if mixed with a different battery type, if inserted incorrectly, if all

the batteries are not replaced at the same time, if disposed of

in a fire or if an attempt is made to charge a battery not in-

tended to be recharged.

Fig. 5

Manual or Remote Operation

Flame effect

Setting Operation

Press the ‘ON’ button once

Indication

Bottom Neon

Flame effect & 1kW

heat

Press the ‘ON’ button again Bottom &

Middle Neon

Flame effect & 2kW

heat

Press the ‘ON’ button again All 3 Neon’s

To turn off any of the

settings

Press the ‘OFF’ button once

To increase or decrease the brightness of the fuel effect use the buttons as

shown in Fig. 5

Thermostat Operation (see Fig. 6)

The thermostat controls the heat output according to the room

temperature. This ensures that the heater will not produce

heat unnecessarily when the room is warm.

To set the temperature you require, turn the thermostat knob

fully clockwise to ‘max’ position. When the room is warm

enough, turn the knob back slowly until the thermostat just

clicks off. The heater will now maintain your selected tem-

perature.

Note : Once the thermostat has switched the appliance OFF

it may take some time before the heater comes back on. This

does not mean that the appliance is faulty.

Remote Control

Warning: it takes time for the re-

ceiver to respond to the trans-

mitter. Do not press the buttons

more than once within two sec-

onds for correct operation.

Manual Controls

Note : The Standby

Switch must first be

turned on to operate

either the manual or

the remote controls.

Thermostat Fig. 6

Thermal Safety Cut-out

A thermal safety cut-out is incorporated in the heater to pre-

vent damage due to overheating.

This can happen if the heat outlet was restricted in any way.

The heater will switch on once the obstruction has been re-

moved and the heater has cooled. If the cut-out continues to

operate intermittently, the heater should be switched off and

a service agent contacted.

Maintenance

WARNING: ALWAYS DISCONNECT FROM THE POWER

SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE.

Instructions for fitting Coal Option

Introduction

Your fire is provided with a coal effect option. Simply follow

the instructions given below.

Removal of Log Effect

Remove the four screws securing the log effect assembly and

slide out ( see Fig. 7).

Fitting Coal Effect

Fit the coal effect in position and secure with the four screws

(see fig. 8)

Place the coal lumps on the fuel bed. A plastic glove is pro-

vided for handling the coal.

Note: The log effect should be stored away for possible fu-

ture use.

Fig. 7

Fig. 8

Lamp Replacement

To gain access to the lamps remove the coal/log effect from

the fire by unscrewing the four fixing screws from the fuel bed

and sliding out the fuel effect.

Unscrew any defective lamps (see Fig. 9) and replace

with240V, 25 watt E14 SES clear candle lamp. Do not

overtighten.

Refit fuel effect, securing with the four fixing screws.

Fig. 9

Glen Dimplex UK Limited

Millbrook House

Grange Drive

Hedge End

Southampton

Hampshire. SO30 2DF

UK customer help line (8.00AM – 6.00PM Mon-Fri; 8.30AM-1.00PM Sat)

Customer Services: Tel. 0870 7270101

Fax. 0870 7270102

e-mail customer[email protected]

Republic of Ireland Tel. 01 8424833

The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility

(EMC) EN55014, EN60555-2 and EN60555-3 which cover the essential requirements of EEC Directives 73/23 and 89/336

Cleaning

Before commencing cleaning, unplug the heater and allow it

to cool.

The surfaces of the heater should be given an occasional

wipe over with a soft damp cloth. Do not use detergents, abra-

sive cleaning powder or polish on the body of the heater.

The viewing screens should be cleaned carefully with a cham-

ois leather.

DO NOT use proprietory glass cleaners.

To remove any accumulation of dust or fluff the soft brush

attachment of a vacuum cleaner should occasionally be used

to clean the outlet grille of the fan heater.

After Sales Service

Your appliance is guaranteed for one year from the date of

purchase. We undertake to repair or exchange free of charge

within this period, any part with the exception of a lamp found

to be defective due to a manufacturing fault.

Your rights under this guarantee are additional to your statu-

tory rights, which in turn are not affected by this guarantee.

Please retain your receipt as proof of purchase.

This manual suits for next models

Table of contents

Other Dimplex Indoor Fireplace manuals

Dimplex

Dimplex BF33STP User manual

Dimplex

Dimplex BFL50-EU User manual

Dimplex

Dimplex EF830 User manual

Dimplex

Dimplex SP120 User manual

Dimplex

Dimplex BLF50 User manual

Dimplex

Dimplex DCF44GS User manual

Dimplex

Dimplex LVA231 User manual

Dimplex

Dimplex DF3020-EU User manual

Dimplex

Dimplex Dakota User manual

Dimplex

Dimplex DFI2310 User manual

Dimplex

Dimplex Indoor Fireplace User manual

Dimplex

Dimplex DCF7850 User manual

Dimplex

Dimplex VIANA DELUXE VNA20RC User manual

Dimplex

Dimplex DCF7850 User manual

Dimplex

Dimplex BF SERIES User manual

Dimplex

Dimplex BF9000 User manual

Dimplex

Dimplex BLF50-EU User manual

Dimplex

Dimplex Adagio User manual

Dimplex

Dimplex BOF4056 User manual

Dimplex

Dimplex 34" Prism User manual

Dimplex

Dimplex DC700 User manual

Dimplex

Dimplex DWF120330B User manual

Dimplex

Dimplex EF2870 User manual

Dimplex

Dimplex 3-STEP Optimyst Instruction Manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual