Dimplex XLE Series User manual

08/80271/0 ISSUE: 5 Series: A

Dimplex XLE Series Heater

Models: XLE050 / XLE070 / XLE100

XLE125 / XLE150

These instructions should be read carefully and

retained for future use. Note also the information

presented on the appliance.

INSTRUCTION MANUAL

Installation and Operating

IMPORTANT

THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR

FUTURE REFERENCE. Note also the information presented on the appliance

IMPORTANT SAFETY ADVICE

When using electrical heaters, basic precautions should always be followed to reduce

the risk of ﬁre, electrical shock, and injury to persons, including the following:

IMPORTANT – The wall bracket supplied with the heater must be used.

IMPORTANT – All packaging should be disposed of in an appropriate manner.

OVERHEATING WARNING

WARNING - In order to avoid overheating, do not cover or obstruct the heater. Do not

place material or garments on the heater, or obstruct the air circulation around the

heater, for instance by curtains or furniture, as this could cause overheating and a ﬁre

risk. NEVER cover or obstruct in any way the heat outlet slots at the top of the heater

or the air outlet slots in the base of the heater.

WARNING - THE SURFACES ON THIS HEATER CAN BE HOT.

The heater carries a warning ‘DO NOT COVER’ to alert the user to the risk of ﬁre that

exists if the heater is accidentally covered.

CAUTION - Some parts of this product can become very hot and cause burns.

Particular attention has to be given where children and vulnerable people are present.

For your safety this heater is ﬁtted with a thermal cut-out. In the event that the product

overheats for some reason, the cut-out prevents excessive temperatures on the

product by cutting the power to the heater. Once the heater has cooled down, it will

reset automatically, it will continue to cycle on and o automatically until the reason for

overheating is removed.

The display screen may ﬂash red to indicate the product has overheated. To reset the

display, remove the obstruction and hold Enter for 10 seconds.

SUITABLE APPLICATIONS

WARNING - This heater is suitable for normal domestic household purposes and should not

be used in any other type of environment. This product should only be used in the country

where it was purchased from by a recognised commercial retailer. Do not use outdoors.

SERVICING AND REPAIRS

WARNING - Servicing and product repairs should only be undertaken by the

manufacturers approved service agent or a similarly trained or qualiﬁed person, using

only exact manufacturer approved spare parts.

PLEASE NOTE: Household dust, lit cigarettes, candles and oil burners, combined with

the convection eect of electric heaters can cause signiﬁcant soot deposits to build

up on the surface directly above and to the sides of the heater. This is not a fault of the

heater. Extensive burning of candles or smoking in the operating environment of this

product can produce heavy discolouration within a few months of use.

CAUTION

FAILURE TO FOLLOW THESE INSTRUCTIONS MAY CAUSE INJURY AND/OR

DAMAGE AND MAY INVALIDATE YOUR GUARANTEE

OPERATING WARNINGS

IMPORTANT: Remember to observe all safety warnings and precautions when operating

the heater on the automatic or timer modes, either attended or unattended since a ﬁre

risk exists when the heater is accidentally covered or obstructed.

Mains cables are not provided with this heater.

CAUTION: Do not use if either of the heater’s mains power leads become damaged. If

the supply cord is damaged it must be replaced by the installer or an approved Dimplex

service partner.

Curtains must not come to within 250mm of the top of the heater.

Do not sit or stand on the heater.

Do not place objects in contact with the heater.

To maintain stability, it is essential that the heater is placed on a level surface and care

should be taken to avoid irregular surfaces, such as may result from carpets or tiled

surrounds partially protruding under the heater.

ELECTRICAL INSTALLATION

The installation of the heater should be carried out by trained personnel.

WARNING - Minimum clearances and IP zone requirements must be adhered to in

accordance with the current wiring regulations.

WARNING - The electrical installation of this heater must be carried out by a suitably

qualiﬁed or trained electrician, and be in strict accordance with current wiring Regulations.

The peak supply must be connected via a switched fused spur with a fuse rated suitably

for the appliances ﬂex, the o-peak supply , via a 20A double pole switch. Failure to

follow these instructions will mean that the manufacturer’s instructions have not been

adhered to. THERE ARE NO EXCEPTIONS.

• This heater must be earthed

• Not suitable for connection via a plug top

• Do not locate the heater immediately above or below a ﬁxed electrical point i.e. socket

outlet.

This appliance is intended for installation to a single phase supply only and is not suitable

for connection to 3 phase supplies.

The heater is not ﬁtted with a mains cable, this should be ﬁtted by the installer. Cable

type (minimum size) H05VV-F 1.5mm² three core for peak and 2.5mm² three core for

o-peak for connection to the ﬁxed wiring of the premises through suitable isolation

devices positioned adjacent to the heater. The supply circuits to the heater must

incorporate a double pole isolating switch having a contact separation of at least 3mm.

In installation the supply cord may be cut to the appropriate length for the electrical

connection point. Excess cable should not be inserted or stored behind the heater.

If, during reassembly of the heater, a part of the thermal insulation shows damage or

deterioration, it should be replaced by an identical part.

WARNING: All electrical connections to the terminal block must be secure to prevent

risk of ignition. Tighten to 0.5 Nm.

CHILD SAFETY

WARNING - Fixing kit screws are a potential choking hazard.

WARNING - This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction concerning use of appliance by

a person responsible for their safety.

This appliance can be used by children from 8 years and above and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge

if they have been given supervision or instruction concerning use of the appliance.

Children shall not play with the appliance. Cleaning and user maintenance shall not be

made by children without supervision.

Children of less than 3 years should be kept away unless continuously supervised.

Children aged from 3 years and less than 8 years shall only switch on/o the appliance

provided that it has been placed or installed in its intended normal operating position

and they have been given supervision or instruction concerning use of the appliance in

a safe way and understand the hazards involved. Children aged from 3 years and less

than 8 years shall not regulate and clean the appliance or perform user maintenance.

Models XLE050 XLE070 XLE100 XLE125 XLE150

Nominal Output (kW) 0.50 0.75 1.00 1.25 1.50

Storage Element Rating

230/240V~: 936/1020W 1435/1560W 2042/2220W 2540/2760W 3024/3300W

Boost Output 230/240V~: 312/340W 479/520W 681/740W 847/920W 1008/1100W

Rated Charge Period: 7.7 - 7 Hours 7.7 - 7 Hours 7.7 - 7 Hours 7.7 - 7 Hours 7.7 - 7 Hours

kWh: 7.14kWh 10.9kWh 15.5kWh 19.3kWh 23.1kWh

Fan Wattage 11W 11W 11W 11W 11W

UI Wattage 0.5W 0.5W 0.5W 0.5W 0.5W

Sound Level dB

(measured in test chamber) 27 29 32 30 31

Energy Cell Packs Required

(047243) 4 6 8 10 12

Installed Weight: 63kg 85kg 107kg 133kg 155kg

Height (mm) 749 749 749 749 749

Width (mm) 581 703 825 947 1069

Depth (mm) 182 182 182 182 182

All Models

Controls

Digitally controlled, Electronic Thermostat accurate to (±0.2°C). Setpoint range (7-26°C)

Timer modes:

7 Day Programmable User Timer, Out All Day, Holiday

Continuous heat modes:

Setback

Controller UI

• Graphical display with RGB backlight

• Capacitive buttons with audio feedback

• User replaceable battery (Coin-Type)

Controller Functions

• Open window detection

• Automatic Charge Control

• Bluetooth for software updates

• Child Lock

Safety Features Electronic overheat protection. Additional electromechanical overheat protection.

LVD and EMC compliance.

Storage Core High-density bonded magnetite energy cells

Colour/ Finish White (RAL 9016) ‘Trac White’. Grill RAL7035 anodised

Battery Backup 3.3V coin cell battery to backup real time clock. Battery life > 5 years.

Supply (each) 1/N/PE 230-240V / 50Hz (Peak / O Peak) Class ll

IP Rating IPX4

Approvals CE & BEAB

Warranty 2 Years

Country of Origin United Kingdom

Manufacturer Glen Dimplex Heating & Ventilation (GDC Group Ltd.)

Technical Details

Preparation

Models 050 070 100 125 150

Feet Position

1 ‘A/B’ 167/124 167/185 167/246 160/314 160/375

Feet Position

2 ‘A/B’ 93/198 93/259 93/320 100/374 100/435

749mm

150mm

(min)

150mm

(min)

1. Place the heater within its packaging

ﬂat on the ground with arrows printed

on the base of the carton pointing

upwards.

2. Feet are ﬁtted in the default position

(Xposition) and can be moved to

the outside position (Yposition) if

necessary. (Fig. 1a and Fig. 1b). NB:

Repositioning of feet may be required

depending on ﬂoor arrangement (e.g.

replacing an installation).

Stand the heater on its feet before

removing the packaging.

CAUTION SHOULD BE TAKEN NOT TO

REST THE HEATER UPON THE ROOM

TEMPERATURE SENSOR HOUSING. (Fig. 1b)

Dispose of packaging in an appropriate way.

Read these instructions carefully before

proceeding any further with the installation.

3. Ensure the heater is stable before removing the screws which hold the bottom grille

panel in position. (Fig. 2) Set the bottom grille to one side, avoiding its sharp edges

when handling.

4. Remove the two screws securing the front panel, located at the bottom of the heater

(Fig. 3). Once removed set carefully to one side to avoid damage.

NOTE - Retain these screws for reassembly. If misplaced, M4 x 10 Tritap screws must be

used. IMPORTANT - Do not use the outer top panel or the rear heat shield to lift or carry

the heater.

Room Sensor

Housing

Fig. 1bFig. 1a

Do not place objects within 300mm of the front of the heater

and 150mm (min. 75mm) either side.

250 mm

300 mm

150 mm

Ensure the back of the heater is ﬂush against the wall. If the skirting board is

taller than 120mm and deeper than 15mm it should be cut to accommodate safe

installation of the heater.

120 mm

15 mm

150 mm

Fig. 2 Fig. 3

The heater must be securely ﬁxed to a wall. Screws with suitable wall ﬁxings for solid

walls are provided. If other wall types are encountered it is the installer who must

choose the most suitable ﬁxing.

SUGGESTED FIXINGS

SOLID BRICK/BLOCK: No. 10 size high temperature resistant plastic inserts, 8mm drill

bit. Drill hole 15mm deeper than plastic insert length.

PLASTERBOARD - If possible locate studding and use No. 10 woodscrews directly

into the wood, otherwise M5 rawlplug intersets are suitable.

NOTE: FOR OTHER WALL TYPES (eg. timber frame and hollow concrete) SEEK

SPECIALIST ADVICE.

If the ﬂoor is carpeted then the carpet should be slit and underlay cut away to allow

the feet to rest ﬁrmly on the ﬂoor. Carpet gripper must be locally removed so that the

feet may rest in a level position.

This appliance is heavy. The ﬂoor must be checked to ensure that it is capable of

bearing the weight of the unit, up to 165kg.

This Heater is rated IPX4

DO NOT UNDER ANY CIRCUMSTANCES ATTEMPT TO MOVE OR REPOSITION

THIS HEATER WITHOUT SEEKING EXPERT ADVICE. THE HEATER SHOULD

NEVER BE FREED FROM THE WALL WITH ENERGY CELLS INSIDE.

USECAUTIONWHENINSTALLINGTHISPRODUCT,UNPAINTED METALWORK

CAN HAVE SHARP EDGES.

IMPORTANT Head of wall ﬁxing screw must be ﬂanged pan head type and have a

diameter no less than 11mm. No countersunk headed screws to be used for wall ﬁxing.

Installing the Heater

Fig. 4 Fig. 5

5. Place the heater in its ﬁnal position and mark the ﬁxing holes through the location

holes visible through the back of the heater.

6. Six ﬁxing positions must be selected for models XLE100, XLE125, XLE150 and at

least 4 ﬁxing positions for models XLE050 and XLE070. Fig. 6.

Common ﬁxing points for all heater sizes are shown in both Fig. 4 and Fig. 5.

Mark the positions for the ﬁxing holes towards the bottom of each slot, this allows the

heater to settle once the energy cells have been ﬁtted.

Move the heater away from the wall, drill the holes and ﬁt the wall ﬁxings best suited

to the application.

Secure the heater to the wall using correct quantity of screws required per model,

using the appropriate screw ﬁttings.

NB: Do not fully tighten screws until energy cells are fully loaded to ensure full

weight is on feet and not on the wall ﬁxings.

NOTE: UNDER NO CIRCUMSTANCES SHOULD ANY SCREWS BE REMOVED

WITHOUT FIRST REMOVING ALL ENERGY CELLS FROM THE HEATER.

NEVER FREE THE HEATER FROM THE WALL WITH ENERGY CELLS REMAINING

INSIDE THE HEATER CAVITY.

NOTE: ANY FIXING DROPPED INTO HEATER MUST BE RETRIEVED AS THEY MAY

IMPACT PRODUCT SAFETY OPERATION.

Fig. 6

Warning: Before obtaining access to terminals, all supply circuits must

be disconnected.

7. The heater leaves the factory conﬁgured to operate with two mains supplies, a 24

hour peak supply and an o peak switched supply. (Fig. 7)

Not suitable for use on single supply.

Storage / Fan circuit

Fan Circuit = PEAK L

Storage Circuit = OFF-PEAK L

Fan Circuit = PEAK N

Storage Circuit = OFF-PEAK N

The earth wire should be connected into the earth terminal block marked E

WARNING: Terminal block maximum torque 0.5 Nm

Neutral

Live

(O-Peak)

Neutral

Live

(Peak)

Earth

(Both Supplies)

Switched Supply

Terminal Block

Mains

Cable

Tighten Screws

Electrical Connections

Fig. 7 Fig. 8

Other manuals for XLE Series

This manual suits for next models

Table of contents

Languages:

Other Dimplex Heater manuals

Dimplex

Dimplex B075E User manual

Dimplex

Dimplex PLX050NN User manual

Dimplex

Dimplex RFV-800 User manual

Dimplex

Dimplex FX 20VE User manual

Dimplex

Dimplex EUL-B Series User manual

Dimplex

Dimplex TAYLOR SUITE User manual

Dimplex

Dimplex DXUCTW2B User manual

Dimplex

Dimplex OFC1205 User manual

Dimplex

Dimplex DTD Series User manual

Dimplex

Dimplex AC3CE User manual

Dimplex

Dimplex PLX 500 User manual

Dimplex

Dimplex OFRC15 User manual

Dimplex

Dimplex R23SH Series User manual

Dimplex

Dimplex ARC10E User manual

Dimplex

Dimplex DEUF2N User manual

Dimplex

Dimplex DIRP15A10GR User manual

Dimplex

Dimplex CXLS12N User manual

Dimplex

Dimplex LEE Series User manual

Dimplex

Dimplex OCR15TIF User manual

Dimplex

Dimplex CXD2000H-NA Series User manual

Dimplex

Dimplex ROF2T User manual

Dimplex

Dimplex HAW1000N User manual

Dimplex

Dimplex DXFF30TSN User manual

Dimplex

Dimplex OFC1000 User manual

Popular Heater manuals by other brands

oventrop

oventrop Regucor Series quick start guide

Blaze King

Blaze King CLARITY CL2118.IPI.1 Operation & installation manual

ELMEKO

ELMEKO ML 150 Installation and operating manual

BN Thermic

BN Thermic 830T instructions

KING

KING K Series Installation, operation & maintenance instructions

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Installation instructions and owner's manual

Well Straler

Well Straler RC-16B user guide

EUROM

EUROM 333299 instruction manual

Heylo

Heylo K 170 operating instructions

Eterna

Eterna TR70W installation instructions

Clarke

Clarke GRH15 Operation & maintenance instructions

IRSAP

IRSAP The Radiator Company Ovali Fitting instructions

Empire Heating Systems

Empire Heating Systems WCC65 Installation and owner's instructions

Wetekom

Wetekom 92 86 43 Original instructions

Desa

Desa SPC170-F owner's manual

Watlow

Watlow Watrod Electric Tubular Heaters Specifications

Haverland

Haverland ECO-DRY GPS Series Instruction & installation manual

Stelpro

Stelpro ASILVC2060 Series user guide