Dimplex EPX User manual

Quick Start Guide

EPX Panel Heater with RX24TI Programmer

EPX Panel Heater fitted with RX24TI Programmer

Issue 1 D1223-0106

This guide is for quick reference only. Refer to EPX/RX24TI installation and operating instructions for further information.

EPX panel heaters are fitted with an integral

thermostat and On/Off switch.

With the addition of an RX24TI timer, the

heater can be programmed to automatically

switch on/off at different times of the day.

The RX24TI is fitted by removing the plastic

cover adjacent to the thermostat and simply

slotting into place.

The RX24TI may be removed from the for

easy programming if required.

(A) Thermostat: slide the thermostat control to the appropri-

ate position to give comfort level required.

Heater will automatically switch on and off as necessary to

maintain the selected temperature. A higher setting will

make the room warmer.

(B) Power switch

(D) Heat indicator: Illuminates when the heater is delivering

heat

MODE selection

There are three different operating

modes. Press MODE to cycle

through these:

MAN OFF heating is permanently

off

MAN ON heating is permanently

on (cycles on thermostat)

AUTO operates the heating in

conjunction with the program

Glen Dimplex UK Ltd. Millbrook House, Hedge End, Southampton, SO30 2DF. For further assistance please contact Dimplex customer services on 0870 727 0101

BD C

RX24TI programmer set up

To program the RX24TI for the first time, it will need to be plugged

into the heater to charge up.

When operated in the heater, the display is lit (blue); this turns off

after a short period of inactivity.

When removed from the heater for programming, the display is not

lit.

Set the Time

Press the PROG key once to set

the time.

The symbol appears on the

screen.

Set the hours using the

keys. Press ENTER and repeat

the process to set the minutes.

When complete, press ENTER

again. The time is now set.

Set the daily program

Up to 4 program (on/off) periods

can be set for the 24 hour period.

Press PROG twice.

P1 ON is displayed, denoting the

first ON time setting.

Set the hours/minutes for the first

On period using the but-

tons, in the same way as for set-

ting time (above).

Note, the minutes are set in 10

minute blocks.

Once the P1 ON time is set, press ENTER and set the P1 OFF time

(i.e. the time at which the heater should switch off).

Repeat the procedure for P2 - P4 for as many on/off periods as

required.

If less than 4 on/off periods are needed, simply leave the unneeded

periods in their default setting.

After programming P4, the display automatically returns to the

default screen.

Example time program:

The example below explains how 4 time program periods can be

set up to allow the heater to operate at times when the room is

occupied.

P1 ON: 06:00 P2 ON: 11:00 P3 ON: 16:00 P4 ON: 00:00 (unused)

P1 OFF: 07:30 P2 OFF: 12:00 P3 OFF: 21:00 P4 OFF: 00:00 (unused)

Program Advance

Heater controls

When in AUTO mode, to “Advance” the program to the next time

block, press the button for 2 seconds.

“ADVANCE” appears on the display.

Press and hold for 2 seconds to cancel the program advance.

Table of contents

Other Dimplex Heater manuals

Dimplex

Dimplex BLF7451 User manual

Dimplex

Dimplex FX 20E IPX4 User manual

Dimplex

Dimplex DXUCTW2B User manual

Dimplex

Dimplex AC3RN User manual

Dimplex

Dimplex DEOC15 User manual

Dimplex

Dimplex CKHA Series Configuration guide

Dimplex

Dimplex DX 421 User manual

Dimplex

Dimplex QUBEFAN Q2TSNH User manual

Dimplex

Dimplex MH NO Series User manual

Dimplex

Dimplex Studio G DXSTG25 User manual

Dimplex

Dimplex DEP Series User manual

Dimplex

Dimplex ECR15 User manual

Dimplex

Dimplex Electric Unit Heaters User manual

Dimplex

Dimplex IRX50N User manual

Dimplex

Dimplex 402T User manual

Dimplex

Dimplex PLX050E User manual

Dimplex

Dimplex LC Series User manual

Dimplex

Dimplex DXDF20 User manual

Dimplex

Dimplex DGP1000-B User manual

Dimplex

Dimplex WFE3BE User manual

Dimplex

Dimplex QUBEFAN Q2BT User manual

Dimplex

Dimplex DESC2TN User manual

Dimplex

Dimplex DHCH20E User manual

Dimplex

Dimplex PLX 500 User manual

Popular Heater manuals by other brands

oventrop

oventrop Regucor Series quick start guide

Blaze King

Blaze King CLARITY CL2118.IPI.1 Operation & installation manual

ELMEKO

ELMEKO ML 150 Installation and operating manual

BN Thermic

BN Thermic 830T instructions

KING

KING K Series Installation, operation & maintenance instructions

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Installation instructions and owner's manual

Well Straler

Well Straler RC-16B user guide

EUROM

EUROM 333299 instruction manual

Heylo

Heylo K 170 operating instructions

Eterna

Eterna TR70W installation instructions

Clarke

Clarke GRH15 Operation & maintenance instructions

IRSAP

IRSAP The Radiator Company Ovali Fitting instructions

Empire Heating Systems

Empire Heating Systems WCC65 Installation and owner's instructions

Wetekom

Wetekom 92 86 43 Original instructions

Desa

Desa SPC170-F owner's manual

Watlow

Watlow Watrod Electric Tubular Heaters Specifications

Haverland

Haverland ECO-DRY GPS Series Instruction & installation manual

Stelpro

Stelpro ASILVC2060 Series user guide