Delta VFD-M-D series User manual

-M-D

Preface

Thank you for choosing DELTA’s high-performance VFD-M-D Series. The VFD-M-D Series is

manufactured with high-quality components and materials and incorporate the latest microprocessor

technology available.

This manual is to be used for the installation, parameter setting, troubleshooting, and daily

maintenance of theAC motor drive. To guarantee safe operation of the equipment, read the following

safety guidelines before connecting power to the AC motor drive. Keep this operating manual at hand

and distribute to all users for reference.

To ensure the safety of operators and equipment, only qualified personnel familiar with AC motor

drive are to do installation, start-up and maintenance. Always read this manual thoroughly before

using VFD-M-D series AC Motor Drive, especially the WARNING, DANGER and CAUTION notes.

Failure to comply may result in personal injury and equipment damage. If you have any questions,

please contact your dealer.

PLEASE READ PRIOR TO INSTALLATION FOR SAFETY.

DANGER!

1. AC input power must be disconnected before any wiring to the AC motor drive is made.

2. A charge may still remain in the DC-link capacitors with hazardous voltages, even if the power

has been turned off. To prevent personal injury, please ensure that power has been turned off

before opening the AC motor drive and wait ten minutes for the capacitors to discharge to safe

voltage levels.

3. Never reassemble internal components or wiring.

4. The AC motor drive may be destroyed beyond repair if incorrect cables are connected to the

input/output terminals. Never connect the AC motor drive output terminals U/T1, V/T2, and

W/T3 directly to the AC mains circuit power supply.

5. Ground the VFD-M-D using the ground terminal. The grounding method must comply with the

laws of the country where the AC motor drive is to be installed. Refer to the Basic Wiring

Diagram.

6. VFD-M-D series is used only to control variable speed of 3-phase induction motors, NOT for 1-

phase motors or other purpose.

7. VFD-M-D series is the specific drive for the elevator door and other automatic door control,

NOT for those devices that may cause personal injury, such as life support equipment or any

life safety situation.

8. VFD-M-D is produced with strict quality management. It will need the safety device when it is

used in those occasions that may cause severe accident due to the malfunction.

WARNING!

1. DO NOT use Hi-pot test for internal components. The semi-conductor used in the AC motor

drive is easily damaged by high-pressure.

2. There are highly sensitive MOS components on the printed circuit boards. These components

are especially sensitive to static electricity. To prevent damage to these components, do not

touch these components or the circuit boards with metal objects or your bare hands.

3. Only quality person is allowed to install, wire and maintain AC motor drive.

CAUTION!

1. Some parameter settings will cause the motor to run immediately after applying power.

2. DO NOT install the AC motor drive in a place subjected to high temperature, direct sunlight,

high humidity, excessive vibration, corrosive gases or liquids, or airborne dust or metallic

particles.

3. Only use AC motor drives within specification. Failure to comply may result in fire, explosion or

electric shock.

4. To prevent personal injury, please keep children and unqualified people away from the

equipment.

5. When the motor cable between the AC motor drive and motor is too long, the layer insulation of

the motor may be damaged. Please use a frequency inverter duty motor or add an AC output

reactor to prevent damage to the motor. Refer to appendix B Reactor for details.

6. The rated voltage for the AC motor drive must be ≤240V and the mains supply current capacity

must be ≤5000A RMS.

Table of Contents

Preface .............................................................................................................i

Table of Contents..........................................................................................iii

Chapter 1 Introduction................................................................................1-1

1.1 Receiving and Inspection ...................................................................1-1

1.1.1 Nameplate Information................................................................ 1-1

1.1.2 Model Explanation ...................................................................... 1-1

1.1.3 Series Number Explanation ........................................................ 1-2

1.2 Appearances......................................................................................1-2

1.3 Preparation for Installation and Wiring ...............................................1-3

1.3.1 Remove Keypad ......................................................................... 1-3

1.3.2 Remove Front Cover................................................................... 1-3

1.4 Lifting..................................................................................................1-3

1.5 Storage...............................................................................................1-4

Chapter 2 Installation and Wiring ..............................................................2-1

2.1 Ambient Conditions ............................................................................2-1

2.2 Installation..........................................................................................2-1

2.3 Dimensions.........................................................................................2-3

2.4 Wiring.................................................................................................2-4

2.4.1 Basic Wiring................................................................................ 2-5

2.4.2 External Wiring............................................................................ 2-7

2.4.3 Main Terminals Connections.......................................................2-8

2.4.4 Control Terminals......................................................................2-10

2.4.5 Main Circuit Terminals...............................................................2-13

Chapter 3 Start Up .......................................................................................3-1

3.1 Preparations before Start-up...............................................................3-1

3.2 Operation Method...............................................................................3-2

3.3 Trial Run.............................................................................................3-2

Chapter 4 Digital Keypad Operation ..........................................................4-1

4.1 Description of the Digital Keypad LC-M2E..........................................4-1

4.2 How to Operate the Digital Keypad LC-M2E.......................................4-2

Chapter 5 Parameters..................................................................................5-1

5.1 Summary of Parameter Settings.........................................................5-2

5.2 Description of Parameter Settings....................................................5-15

5.3 The Flow Chart for Parameter Settings ............................................5-87

Chapter 6 Fault Code Information..............................................................6-1

6.1 Common Problems and Solutions ......................................................6-1

6.2 Reset ..................................................................................................6-4

Chapter 7 Troubleshooting.........................................................................7-1

7.1 Over Current (OC)..............................................................................7-1

7.2 Ground Fault.......................................................................................7-2

7.3 Over Voltage (OV)..............................................................................7-2

7.4 Low Voltage (Lv).................................................................................7-3

7.5 Over Heat (OH)...................................................................................7-4

7.6 Overload.............................................................................................7-4

7.7 Display of LC-M2E is Abnormal..........................................................7-5

7.8 Phase Loss (PHL) ..............................................................................7-5

7.9 Motor cannot Run...............................................................................7-6

7.10 Motor Speed cannot be Changed.....................................................7-7

7.11 Motor Stalls during Acceleration.......................................................7-8

7.12 The Motor does not Run as Expected..............................................7-8

7.13 Electromagnetic/Induction Noise......................................................7-9

7.14 Environmental Condition ..................................................................7-9

7.15 Affecting Other Machines...............................................................7-10

Chapter 8 Maintenance and Inspections...................................................8-1

Appendix A Specifications........................................................................ A-1

Appendix B Accessories ........................................................................... B-1

B.1 All Braking Resistors & Braking Units Used in AC Motor Drives........B-1

B.1.1 Dimensions and Weights for Braking Resistors..........................B-2

B.2 AMD - EMI Filter Cross Reference.....................................................B-3

B.2.1 Dimensions.................................................................................B-6

B.3 AC Reactor ........................................................................................B-7

B.3.1 AC Input Reactor Recommended Value.....................................B-7

B.3.2 AC Output Reactor Recommended Value..................................B-7

B.3.3 Applications for AC Reactor .......................................................B-7

B.4 Zero Phase Reactor (RF220X00A)..................................................B-10

B.5 Non-fuse Circuit Breaker Chart........................................................B-11

B.6 Fuse Specification Chart..................................................................B-11

Appendix C How to Select the Right AC Motor Drive.............................. C-1

C.1 Capacity Formulas.............................................................................C-2

C.2 General Precaution ...........................................................................C-4

C.3 How to Choose a Suitable Motor.......................................................C-5

Revision Jan. 2007, MDE2, SW V1.05 1-1

Chapter 1 Introduction

1.1 Receiving and Inspection

This VFD-M-D AC motor drive has gone through rigorous quality control tests at the factory before

shipment. After receiving theAC motor drive, please check for the following:

 Check to make sure that the package includes an AC motor drive, the User Manual/Quick

Start and CD, dust covers and rubber bushings.

 Inspect the unit to assure it was not damaged during shipment.

 Make sure that the part number indicated on the nameplate corresponds with the part

number of your order.

1.1.1 Nameplate Information

Example for 0.5HP/0.4kW 230V 1-Phase230VAC motor drive

Serial Number & Bar Code

ACDrive Model

Input Spec.

OutputSpec.

Output Frequency Range

Software version

MODEL

INPUT

OUTPUT

FREQUENCYRANGE

: VFD004M21B-D

:1PH 6.3A/3PH 3.2A 200-240V 50 / 60Hz

:3PH 0-240V 2.5A 1.0kVA 0.5HP

: 0.1-400Hz

004M21BDT5220001

01.02

1.1.2 Model Explanation

VFD B

Version Type

MainsInput Voltage

21: Single phase230V

M Series

004

Applicable motorcapacity

004:0.5 HP(0.4kW)

Series Name ( ariable requency rive)

VF D

D-

SpecificAC Motor Drives

for Elevator Door

Table of contents

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual