Dell Inspiron 24 User manual
1
2.5” SSD Installation Guide –for Windows
What do I need?
Clear Workspace
2.5” Solid State Drive
Computer User Manual - (to show location of memory slots)
Screwdriver - (for removing computer case or memory panel)
SSD Installation Kit
To prevent potential damage from anti-static electricity, you
should discharge yourself first.
This can be done by simply touching a grounded metal object,
such as a radiator.
If you are leaving the original Drive installed and installing the new SSD
alongside it, you will also need:
Spare Internal Power Cable
Spare SATA Data Socket on the Motherboard
Spare 2.5”/3.5” Drive Bay inside the Computer
If upgrading an All-in-One machine, you may also require:
SATA Drive Carrier
2
Before you begin…
If you are cloning the original Drive –ensurethat the USED capacity of the old Drive is
LESS than the capacity of the new SSD
Back-up all important data on the old Drive to an external storage device –such as a
USB Hard Drive or DVD
Version A - Replacing an existing Drive
This guide assumes that you are replacing an existing Drive and you do not have a spare
Drive Bay (this is the most likely scenario if you are upgrading a Laptop and some All-in-
One Computers).
If your device has more than 1 Drive Bay and you want to leave the old Drive installed,
please follow Version B on Page 4
1 –Before Cloning
a. Insert the SSD into the External Drive
Enclosure
b. Using the USB Cable, connect the External
Drive Enclosure to the Computer
c. You are now ready to copy the Data from
the Original Drive to the SSD –please refer
to the Cloning Section below on Page 5
Installation
Replacing an Old Drive with a new SSD? –Follow Version A below
(e.g. Upgrading your Laptop or All-in-One Hard Drive)
Installing new SSD alongside Old Drive? –Follow VersionB on Page 4
(e.g. Desktop or Server with an additional Drive Bay)
3
2 –After Cloning:
d. Remove the new SSD from the
External Drive Enclosure
e. Turn off the power to your
Computer. Disconnect the power
supply and remove the battery
pack (if removable)
f. If present, remove the System
Drive Bracket and reassemble with
the new SSD
g. If your SSD was supplied with an
adaptor/spacer and you are
installing into a Laptop, you may
need this to match the depth of
the SSD with the Old Drive.
Remove the adhesive backing
from the adaptor, align it with the
outer edges on the label-side of
the SSD and firmly press the
adhesive side onto the SSD
surface
h. Alternatively, at this stage, you
may need to install the SSD into a
3.5” SATA Drive Carrier
i. Install the reassembled SSD into
the Drive Bay of the Computer
j. Replace the panel or enclosure
and turn on your Computer
4
Version B - Adding an Extra Drive
This guide assumes that you are keeping the old Drive installed (e.g. to be used for data
storage). If you are not keeping the old Drive in the Computer, or if the Computer does
not have a spare Drive Bay or SATA Connection to install both old and new Drives at the
same time, please follow Version A on Page 2
1 –Make sure the computer is
completely shut down and switched off.
2 –Unplug every cable from the
Computer, making a note of which cable
goes where.
3 –Remove the outer casing. This is
normally done by removing the screws
that hold it in place.
4 –Attach the 2.5” to 3.5” Mounting Brackets
to the SSD by aligning the Mounting Screw
Holes on the Brackets with those on the SSD
and inserting the M3 Flat Head Screws.
5 –Locate an available 2.5”/3.5” Bay inside
the Computer and install the SSD using the
Screws.
NB –Your system may require proprietary chassis screws, rails or a bracket system to be
used with its Drive Bay(s). In this case, please attach that hardware to the 2.5” to 3.5”
Mounting Bracket for compatibility with the Computer’s Chassis.
5
6 –Attach one end of the SATA Data
Cable to the SATA Connector on the
Computer’s Motherboard or SATA Host
Cable. The SATA Connectors are keyed
to ensure the correct orientation.
7 –Attach the other end of the SATA
Data Cable to the SSD.
8 –Attach the Power Cable to the SSD
9 –You are now ready to copy the Data from the original Drive to the new SSD.
Please skip to the Cloning section below
Cloning
If you have a software disk supplied with your SSD Kit, please insert that into your
Computer’s optical drive and follow the instructions
If you do not have a CD or Optical Drive, you will need to use the SSD Manufacturer’s
Software, which is downloadable from their website.
Please see the SSD Installation Section on mrmemory.co.uk/support for the latest
cloning software website links
Email –support@mememory.co.uk
Tel –01903 692 214
Other manuals for Inspiron 24
1
This manual suits for next models
1
Table of contents
Other Dell Desktop manuals
Dell
Dell Precision 7960 User manual
Dell
Dell OptiPlex 745c User manual
Dell
Dell Inspiron 3668 Operation and maintenance manual
Dell
Dell Vostro 3650 User manual
Dell
Dell OptiPlex Gn+ User manual
Dell
Dell Latitude 5175 User manual
Dell
Dell OptiPlex 3240 User manual
Dell
Dell OptiPlex 330 User manual
Dell
Dell Dimension 8300 Series Manual
Dell
Dell XPS 710 User manual
Dell
Dell Alienware Area-51 R4 User manual
Dell
Dell Dimension 0JH552A01 User manual
Dell
Dell OptiPlex XE Small Form Factor User manual
Dell
Dell Precision 3460 Small Form Factor User manual
Dell
Dell Wyse Z90D7 User manual
Dell
Dell Precision R5400 User manual
Dell
Dell XPS DC01L User manual
Dell
Dell OptiPlex 5080 User manual
Dell
Dell XPS 210 User manual
Dell
Dell XPS 8700 User manual
