Cross Technologies 2016-05A User manual

Instruction Manual

Model 2016-05A

L-Band Downconverter

April 2017 Rev.A

EXECUTE

MODEL 2016

DOWNCONVERTER

CROSS TECHNOLOGIES INC.

F=1525 G=25

MUTE ALARM REMOTE POWER

Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc.,

but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc.

for purposes of operating the equipment.

When ordering parts from Cross Technologies, Inc., be sure to include the equipment

model number, equipment serial number, and a description of the part.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

INSTRUCTION MANUAL

MODEL 2016-05A Downconverter

TABLE OF CONTENTS PAGE

Warranty 2

1.0 General 3

1.1 Equipment Description 3

1.2 Technical Characteristics 4

1.3 Monitor & Control Interface 5

2.0 Installation 7

2.1 Mechanical 7

2.2 Rear Panel Inputs & Outputs 8

2.3 Front Panel Controls & Indicators 9

2.4 Operation 10

2.5 Menu Settings 11

WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.

All Cross Technologies, Inc. products are warranted against defective materials and

workmanship for a period of one year after shipment to customer. Cross Technologies,

Inc.’s obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s

option, replacing parts, subassemblies, or entire assemblies. Cross Technologies, Inc. shall

not be liable for any special, indirect, or consequential damages. This warranty does not

cover parts or equipment which have been subject to misuse, negligence, or accident by the

customer during use. All shipping costs for warranty repairs will be prepaid by the

customer. There are not other warranties, express or implied, except as stated herein.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

2016-05A Manual, Rev A Page 2 04/17/17

MODEL 2016-05A Downconverter

1.0 General

1.1 Equipment Description

2016-05A L-Band Downconverter converts 950 to 1525 MHz to 140 MHz in 1 MHz steps with low group

delay and flat frequency response. The 2016-05A Input and Output levels have been optimized to support

transmit from an L-band modem to a 140 MHz IF upconverter. Multi-function push button switches select the

RF frequency, gain, and other parameters. Front panel LEDs provide indication of DC power (green), PLL

alarm (red), and remote operation (yellow). The gain is adjustable from 0 to +50 dB. Remote operation allows

selection of frequency and gain. Parameter selection and frequency and gain settings appear on the LCD

display. Standard connectors are BNC female for IF output and the optional external reference input and

reference output, and Type F female for the RF input. A high stability (±0.01ppm) reference, LNB +24 VDC,

0.4 Amps power and 10 MHz reference (includes a 10 MHz output connector), are available Options. The unit

is powered by a 100-240 ±10% VAC power supply, and housed in a 1.75” X 19” X 16” 1RU chassis.

EXECUTE

MODEL 2016

DOWNCONVERTER

CROSS TECHNOLOGIES INC.

F=1525 G=25

MUTE ALARM REMOTE POWER

FRONT

GND

J10

J18J2

RF IN 10 MHZ REF 10 MHZ

AND

MONITOR EXT REF

LNB FUSE

F1 CONTROL

IF OUT OUTPUT INPUT

DS8

VDC on RF

15 23

REAR

FIGURE 1.1 Model 2016-05A Front and Rear Panels

140

MHz

OUT

.95

1.53

GHz

1750 MHz

1920

MHz

2.7

3.3

GHz

.95 to 2

GHz BP 120 MHz LP

CONTROLLER F=1525 G=25

2016-05A Downconverter Block Diagram

VAR

ATT

10M*

+24*

EXT*

10 M

INT/EXT

10 M

* = OPTIONAL

FIGURE 1.2 Model 2016-05A Downconverter Block Diagram

2016-05A Manual, Rev A Page 3 04/17/17

1.2 Technical Characteristics

TABLE 1.0 2016-05A Downconverter Specifications*

Input Characteristics

Impedance/Return Loss 75Ω/12 dB (see TABLE 2.2 for connector options)

Frequency 950 to 1525 MHz

Noise Figure, Max. 15 dB max gain

Input Level range -60 to -10 dBm

Input 1 dB compression -5 dBm

Output Characteristics

Impedance/Return Loss 75 Ω/18 dB (see TABLE 2.2 for connector options)

Frequency 70 ± 18 MHZ

Output Level/max linear -10 to 0 dBm

Output 1 dB compression +5 dBm

Channel Characteristics

Gain 0.0 to 50.0 dB, 1 dB steps (manually adjustable)

Image Rejection > 50 dB, min

Spurious Response <-45 dBC in band (± 36 MHZ), -20 dBm out

Frequency Response ±1.5 dB, 950 - 1525 MHz; ± 0.5 dB, 72 MHz BW

Group Delay, max 0.0035 ns/MHz2parabolic; 0.025 ns/MHz linear; 1 ns ripple

Frequency Sense Non-inverting

Synthesizer Characteristics

Frequency Accuracy ±1.0ppm max over temp (±0.01ppm option H) internal reference

Frequency Step 1.0 MHz minimum

-100-90-80-70-70

1MHz100kHz10kHz1kHz100 Hz

dBC/Hz

Phase Noise

Fre

External 10 MHz level 0 dBm, ± 3dB, 75Ω(option -E)

Controls, Indicators

Frequency Selection direct readout LCD; pushbutton switches or remote selection

Gain Selection direct readout LCD; pushbutton switches or remote selection

Power Green LED

Alarm Red LED

Remote Yellow LED; RS232C (RS485 option Q), 9600 baud

Other RF Connector Type F (female) (see TABLE 2.2 for other options)

IF Connector BNC (female) (see TABLE 2.2 for other options)

10 MHz Connectors BNC (female), 50/75 Ω(option E)

Connector, Alarm, Remote DB9 - NO or NC contact closure on Alarm

Size 19 inch standard chassis 1.75”high X 16.0” deep

Power 100-240 ±10% VAC, 47 - 63 Hz, 25 watts max.

Options

E Allows ext. 10 MHz ref input, 10 MHz ref can be inserted on the RF in

H High Stability (± 0.01 ppm) internal reference

L LNB +24 VDC, 0.4 Amps with readout of current

Connector options See TABLE 2.2

*+10˚C to +40˚C; Specifications subject to change without notice.

2016-05A Manual, Rev A Page 4 04/17/17

1.3 Monitor and Control Interface

A) Remote serial interface

Protocol: RS-232C, 9600 baud rate, no parity, 8 data bits, 1 start bit, and 1 stop bit.

Connector: Rear panel, DB-9 male

J10 Pinouts (RS-232C/422/485)

Pinouts (RS-232C/422/485)

Pin Function

1 Rx-

2 Rx+ (RS-232C)

3 Tx+ (RS-232C)

4Tx-

5GND

6 Alarm Relay: Common

7 Alarm Relay: Normally Open

8 Not Used

9 Alarm Relay: Normally Closed

B) Commands - Table 1.1 lists the commands for the 2016-05A and briefly describes them. After a command

is sent the 2016-05A sends a return “>” indicating the command has been received and executed.

General Command Format - The general command format is {aaCND...}, where:

{ = start byte

aa = address (RS-485 only - option Q)

C = 1 character, either C (command) or S (status)

N = 1-digit command or status number, 1 through 9

D = 1 character or more of data (depends on command)

} = stop byte

Table 1.1 2016-05A Comman

Commands

Command Syntax* Description

Set Receiver Frequency {aaC2xxxx} where:

• xxxx = 4 characters (7 characters, option X)

• Range: 0950 to 1525 MHz

Set Receiver Gain {aaC4xx} where:

• xxx = 3 characters

• Range: 000 to 500 (0 dB to +50 dB, in 1 dB steps)

Enable 10MHz Ref Insertion {aaC6x} where x =:

(option E only)

• 0 to disable 10MHz insertion on RF input connector

• 1 to enable 10MHz insertion on RF input connector

Enable Spectrum Invert {aaC7x} where x =:

• 0 to disable spectrum invert

• 1 to enable spectrum invert

Enable External 10MHz IN {aaCEx} where x =:

(option E only)

• 0 to disable External 10MHz ref signal

• 1 to enable External 10MHz ref signal

Enable Remote # Just # sign

Disable Remote {aaCR0} {CR and zero}

* PLEASE NOTE: The Address (aa) should only be used when RS-485 is selected.

2016-05A Manual, Rev A Page 5 04/17/17

C) Status Requests - Table 1.2 lists the status requests for the 2016-05A and briefly describes them.

TABLE 1.2 2016-05A Status Reequests

Status Requests

TABLE 1.2 2016-05A Status Requests

Command Syntax* Description

Command Status {aaS1} Returns {S1bbbbcccIA} where:

• bbbb = Rx frequency (bbbbbbb, option X)

• ccc = Rx gain

• I = 1 - spectrum invert enabled

• A = summary alarm; 1=alarmed, 0=normal

10MHz Ref Status {aaS2} Returns {S2ER} where:

(option E only)

• E = 1 - external 10 MHz switched in

• R = 1 - 10 MHz ref inserted on RF input connector

LNB Current {aaS3} Returns {S3eee} where:

(option L only)

• eee = LNB current (000 to 500 = 0 to .500 A)

* PLEASE NOTE: The Address (aa) should only be used when RS-485 is selected.

2016-05A Manual, Rev A Page 6 04/17/17

2.0 Installation

2.1 Mechanical

The 2016-05A consists of one RF/Controller PCB housed in a 1 RU (1 3/4 inch high) by 16 inch deep chassis.

A switching, ±12, +24, +5 VDC power supply provides power for the assemblies. The 2016-05A can be

secured to a rack using the 4 holes on the front panel. Figure 2.1 shows how the 2016-05A is assembled.

POWER

SUPPLY

FIGURE 2.1 2016-05A Mechanical Assembly

2016-05A Manual, Rev A Page 7 04/17/17

2.2 Rear Panel Input/Output Signals - Figure 2.2 shows the input and output connectors on the rear panel.

AC1 - POWER IN

AC input for switching

power supply.

100-240 ±10% VAC,

47-60 Hz.

J2 - RF IN

950-1525 MHz input, -70 to -20 dBm.

see TABLE 2.2.

J1 - IF OUT

140 MHz output, -20 to -30 dBm.

see TABLE 2.2.

J10 - MONITOR AND CONTROL

DB9 female connector.

J1J2

RF IN IF OUT

J10

AND

MONITOR

CONTROL

5 4 3 2

9 8 7 6

10MHz

EXT REF

J3 - 10MHz REF OUT (option -E)

10 MHz external reference input.

BNC female connector.

LNB FUSE

F1 - LNB FUSE (option -L)

1A, Fast Blo, 1/4” fuse. Installing fuse places

+24VDC, 0.4 amps, max on RF IN (J2 center

FIGURE 2.2 2016-05A Rear Panel I/Os

TABLE 2.1 J110

2.1 J10 Pinouts (RS-232C*)

Pin Function

1 Not Used

2 Rx+ (RS-232C)

3 Tx+ (RS-232C)

4 Not Used

5GND

6 Alarm Relay: Common

7 Alarm Relay: Normally Closed

8 Not Used

9 Alarm Relay: Normally Open

*Remote Serial Interface

Interface: DB-9 Male

Protocol: RS-232C, 9600 baud rate, no parity, 8 data bits, 1 start bit, 1 stop bit

TABLE 2.2 IFF/RF

2.2 IF/RF Connector Options

Options

Option IF RF

STD BNC, 75ΩType F, 75Ω

B BNC, 75ΩBNC, 75Ω

C BNC, 75ΩBNC, 50Ω

D BNC, 50ΩBNC, 50Ω

F Type F, 75ΩType F, 75Ω

J BNC, 50ΩType F, 75Ω

K BNC, 50ΩBNC, 75Ω

M BNC, 50ΩType N, 50Ω

N BNC, 75ΩType N, 50Ω

2016-05A Manual, Rev A Page 8 04/17/17

2.3 Front Panel Controls and Indicators - The following are the front panel controls and indicators.

EXECUTE

REMOTEALARM POWER

LCD DISPLAY

Display shows Downconverter

frequency in MHz and Gain in dB

S1 - MENU/EXECUTE BUTTON

Press this to get into Program mode

and to execute any changes.

DS3 - DOWN ALARM LED

Red LED indicates

downconverter alarm.

DS6 - POWER LED

Green LED indicates

presence of DC power.

DS1 - REMOTE LED

Yellow LED indicates

remote operation.

S2 - VERT. TOGGLE

Vertical toggle switch that controls

values in the Menu items when in

program mode. Does not function in the

normal display mode

S3 - HORIZ. TOGGLE

Horizontal toggle switch that

controls which values are being

adjusted. Does not function in the

normal display mode

F=1525 G=+25.0

FIGURE 2.3 2016-05A Front Panel Controls and Indicators

2016-05A Manual, Rev A Page 9 04/17/17

2.4 Operation

2.4.1 Installing and Operating the 2016-05A Downconverter

1. Connect a -20 dBm to -70 dBm signal to RF IN, J2 (Figure 2.2)

2. Connect the IF OUT, J1, to the external equipment

3. Connect 100-240 ±10% VAC, 47 - 63 Hz to AC on the back panel.

4. Set the input frequency (See Section 2.5 Menu Settings).

5. Set the gain for +00.0 to +50.0 dB (See Section 2.5 Menu Settings).

6. Be sure DS6 (green, DC Power) is on and DS3 (red, Alarm) is off (Figure 2.3).

7. Option L only - To insert LNB +24 VDC on the RF center pin install 0.5A fast blo fuse in F1 and check

that DS8 lights yellow (Figure 2.1)

8. AC Fuse - The fuse is a 5 mm X 20 mm, 2 amp slow blow (Type T) and is inserted in the far slot in the

drawer below the AC input as shown in Figure 2.4. There is a spare fuse in the near slot. If a fuse

continues to open, the power supply is most likely defective.

FUSE DRAWER

SPARE FUSE DRAWER

AC Fuse - 2 amp slow blow (Type T 2A GDC),

5 mm X 20 mm

INPUT

100-240± 10%VAC

47-63 Hz

2A MAX

FUSE

TYPE T 2A GDC

250 VOLT

FOR 100 - 240 V~

FIGURE 2.4 Fuse Location and Spare Fuse

2016-05A Manual, Rev A Page 10 04/17/17

Table of contents

Other Cross Technologies Media Converter manuals

Cross Technologies

Cross Technologies 2015-24 User manual

Cross Technologies

Cross Technologies 2115-122 User manual

Cross Technologies

Cross Technologies 1584-29 User manual

Cross Technologies

Cross Technologies 2016-57 User manual

Cross Technologies

Cross Technologies 2005-10 User manual

Cross Technologies

Cross Technologies 3116-192 User manual

Cross Technologies

Cross Technologies 2099-2424 User manual

Cross Technologies

Cross Technologies 4115-300 User manual

Cross Technologies

Cross Technologies 2116-116 User manual

Cross Technologies

Cross Technologies 2016-26 User manual

Cross Technologies

Cross Technologies 2116-300-1600 User manual

Cross Technologies

Cross Technologies 2016-1522 User manual

Cross Technologies

Cross Technologies 2116-182193 User manual

Cross Technologies

Cross Technologies 2117-9395 User manual

Cross Technologies

Cross Technologies 4116-31-184 User manual

Cross Technologies

Cross Technologies 4115-41-212 User manual

Cross Technologies

Cross Technologies 4117-14 User manual

Cross Technologies

Cross Technologies 2099-10 User manual

Cross Technologies

Cross Technologies 2115-275-1845 User manual

Cross Technologies

Cross Technologies 2016-25 User manual

Cross Technologies

Cross Technologies 2015-58T User manual

Cross Technologies

Cross Technologies 2016-8085 User manual

Cross Technologies

Cross Technologies 3116-145-1600 User manual

Cross Technologies

Cross Technologies 2005 User manual

Popular Media Converter manuals by other brands

SoundTraxx

SoundTraxx Blunami BLU-2200 user guide

SPROLINK

SPROLINK VA1 user manual

Acclaim Lighting

Acclaim Lighting DDC-1-AC user guide

Nikon

Nikon AF-S TC-20E III user manual

Axis

Axis AXIS Q7406 user manual

Omega

Omega TAC80B-J instruction sheet

Zoom

Zoom Thunderbolt TAC-2R Operation manual

OST

OST iConverter 10/100M quick start guide

Vertiv

Vertiv Netsure user manual

birddog

birddog MINI user guide

Roland

Roland GI-10 owner's manual

Wallenstein

Wallenstein WX310 Operator's manual

Pace

Pace MSS 200-1 Service manual

Solar Converters

Solar Converters EQ 12/24-50 manual

CYP

CYP EL-7400V Operation manual

TIE

TIE MIDI 1i1o user manual

DCS

DCS Vivaldi Upsampler user manual

Westermo

Westermo MCW-211 SERIES user guide