Cross Technologies 2005-10 User manual

Instruction Manual Model 2005-10

Test Upconverter

April 2009 Rev B

ALARM

CROSS TECHNOLOGIES, INC.

2005 TEST CONVERTER

140

FREQUENCY

GHz

1MHz

10MHz

100MHz

CROSS TECHNOLOGIES, INC.

DC POWER

GAIN

LOW

Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc.,

but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc.

for purposes of operating the equipment.

When ordering parts from Cross Technologies, Inc., be sure to include the equipment

model number, equipment serial number, and a description of the part.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

INSTRUCTION MANUAL

MODEL 2005-10 Test Upconverter

TABLE OF CONTENTS PAGE

Warranty 2

1.0 General 3

1.1 Equipment Description 3

1.2 Technical Characteristics 4

2.0 Installation 5

2.1 Mechanical 5

2.2 Front Panel Controls/Indicators 5

2.3 Rear Panel Input/Output Signals 5

2.4 Accessing the PC Card 6

2.5 Installation/Operation 6

2.6 Environmental Use Information 7

WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.

All Cross Technologies, Inc. products are warranted against defective materials and

workmanship for a period of one year after shipment to customer. Cross Technologies,

Inc.’s obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s

option, replacing parts, subassemblies, or entire assemblies. Cross Technologies, Inc. shall

not be liable for any special, indirect, or consequential damages. This warranty does not

cover parts or equipment which have been subject to misuse, negligence, or accident by the

customer during use. All shipping costs for warranty repairs will be prepaid by the

customer. There are no other warranties, express or implied, except as stated herein.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

2005-10 Manual, Rev. B Page 2 4/28/09

MODEL 2005-10 Test Upconverter

1.0 General

1.1 Equipment Description

The 2005-10 Test Upconverter converts a 70 MHz or 140 MHz IF signal to 2000 to 2500 MHz in 1 MHz steps

with selection of high side LO (C = inverted) or low side LO (Ku = non-inverted) and 70 or 140 MHz input

over the 2.0 - 2.5 GHz range.

Featuring low phase noise, these units are used to loop 70 or 140 MHz modulators to 2.0 - 2.5 GHz receivers

for test purposes. The 70 or 140 MHz carrier input is mixed with a synthesized local oscillator (LO) signal.

The output frequency is selected with four BCD switches which control the synthesized LO. Front panel

LEDs light when DC power is applied (green) and when a PLL alarm occurs (red). The mixer output is

applied to the output attenuator providing a nominal gain of -10 dB (high gain) or -30 dB (low gain).

Connectors are 50ΩBNC (female) for the IF input and for the RF output (other connector options are

available). Wall power supply options are -P for 120 VAC, 60Hz, and -P4 is 100-240 ±10% VAC.

The 2005 can be mounted on a 1 3/4” X 19 “ rack mount panel (option -R).

2000

2500

MHz OUT

140

MHZ IN

1860

2640

MHz

ATTEN

CONTROLLER

FIGURE 1.1 Block Diagram

ALARM

CROSS TECHNOLOGIES, INC.

2005 TEST CONVERTER

140

FREQUENCY

GHz

1MHz

10MHz

100MHz

CROSS TECHNOLOGIES, INC.

DC POWER

GAIN

LOW

FIGURE 1.2 Front and Rear Panel

2005-10 Manual, Rev. B Page 3 4/28/09

1.2 Technical Characteristics

TABLE 1.0 2005-10 Upconverter Specifications*

Input Characteristics

Impedance 50Ω

Return Loss 15 dB

Frequency 70 or 140 MHz center, ± 20 MHz

Level -10 to -25 dBm (LOW GAIN)

-25 to -40 dBm (HI GAIN)

1dB compression 0 dBm (LOW GAIN)

-15 dBm (HI GAIN)

Output Characteristics

Impedance 50Ω

Return Loss 12 dB

Frequency Range 2.0 to 2.5 GHz

Channel Characteristics

Gain -30 dB ± 3 dB (LOW GAIN)

-10 dB ± 3 dB (HI GAIN)

Spurious Response < -40dBC max, < -45dBC typ; OUTPUT NOT FILTERED

Frequency Response ± 2 dB, 2.0 - 2.5 GHz; ± 0.5 dB, any 10MHz increment

Synthesizer Characteristics

Frequency Accuracy ± 25 kHz max

Frequency Step 1.0 MHz minimum

-100

-90

-75

-70

1MHz

100kHz

10kHz

1kHz

100 Hz

dBC/Hz

Phase Noise @ Freq

Indicators

DC Power Green LED

PLL Alarm Red LED

Other

RF, IF Connectors BNC (female)

Size, Bench Top 4.7” wide X 1.75” high X 6.5” deep

Size, Rack Mount 19 inch standard chassis 1.75”high X 7.0” deep (option -R)

AC Power 120 VAC, 60 Hz, 10W max wall mount power supply (option -P) or

100-240 ±10% VAC, 47-63 H, wall mount power supply (option -P4)

*+10 to +40 degrees C; Specifications subject to change without notice

2005-10 Manual, Rev. B Page 4 4/28/09

2.0 Installation

2.1 Mechanical

The 2005 is packaged in an aluminum extrusion. The -R option is mounted on a 1 3/4” X 19” panel that can

be mounted to a rack using the 4 holes at the ends. The unit derives +DC from the RF out center conductor

(+14 to +24 VDC) or the wall power supply (+15V unregulated, option -P, -P4). See Figure 2.3.

2.1.1 Cleaning Instructions

Wipe the exterior with a dry, soft cloth. Use no detergent or cleaning chemicals.

2.2 Front Panel Controls/Indicators - Figure 2.1 shows front panel controls and indicators for the 2005-10.

SW6 - LO SELECT

Slide switch selects high side (C) or

low side (Ku) local oscillator.

DS1 - POWER LED

Lights green when DC

power is present

SW1 to SW4 - FREQUENCY BCD SWITCHES

Select the desired output frequency which is the LO

frequency - 70, -140, +70, or +140 MHz in GHz.

DS2 - ALARM LED

Lights red when PLL

comes out of lock

SW5 - IF SWITCH

Slide switch selects 70 or 140 MHz IF in.

ALARM

CROSS TECHNOLOGIES, INC.

2005 TEST CONVERTER

140

FREQUENCY

GHz

1MHz

10MHz

100MHz

FIGURE 2.1 2005-10 Front Panel Controls and Indicators

2.3 Rear Panel Input/Output Signals - Figure 2.2 shows the input and output signals to the 2005-10.

J1 - IF INPUT

70 or 140 MHz input.

-10 dBm max level for

LOW GAIN (-30 dB)

-30 dBm max level for HI

GAIN (-10 dB)

BNC (female) 50Ω

J3 - DC POWER

The unregulated DC voltage from the

wall power supply (option P, P4).

15 VDC, 200 ma.

J2 - RF OUT

The mixed RF output.

This is an UNFILTERED

output and contains

mainly the RF, LO - IF,

LO, LO + IF, mixer

products.

BNC (female) 50Ω.

SW7 - GAIN SWITCH

Slide switch selects -10 dB high

gain (HI) or -30 dB low gain (LOW).

+15

GND

CROSS TECHNOLOGIES, INC.

DC POWER

GAIN

LOW

FIGURE 2.2 2005-10 Rear Panel Inputs and Outputs

2005-10 Manual, Rev. B Page 5 4/28/09

2.4 Accessing the PC Card

There are NO USER JUMPERS or other on-card controls. ALTHOUGH IT IS NOT RECOMMENDED AND

MAY VOID THE WARRANTY the following shows how to remove the printed circuit board (PCB) from the

extrusion:

1. ALWAYS REMOVE POWER when installing or removing the PCB from the extrusion

2. Remove four (4) rear panel screws (see Figure 2.3).

3. GENTLY pull the rear panel and PCB assembly completely out of the extrusion.

4. To install the PCB, GENTLY push the rear panel and PCB assembly completely into the extrusion

Make sure the shield goes in the lower channel and the PCB in the next channel above that in the

extrusion and that the front panel controls go through the front panel holes.

5. Install four (4) rear panel screws.

EXTRUSION

FRONT SCREWS (4EA)

FRONT PANEL

RACK MOUNT PANEL (FOR -R MODELS ONLY)

REAR SCREWS (4EA)

PCB

ASSEMBLY

REAR PANEL

WALL

POWER

SUPPLY

(-P and -P4 ONLY)

2005 TEST CONVERTER

CROSS TECHNOLOGIES, INC.

100MHz

FREQUENCY

10MHz

1MHz

GHz

140

ALARM

FIGURE 2.3 2005 Assembly Drawing

2.5 Installation / Operation

2.5.1 Installing and Operating the 2005-10

1. If using the receiver LNB voltage to power the 2005-10, be sure +14 to +24 VDC is on the RF

center conductor. If using the wall power supply (options -P or -P4), connect the power supply to

the DC POWER connector and either 120 VAC (-P) or 100-240 ±10% VAC (-P4) (Figure 2.2)

2. Select either C or KU band (SW6) and either 70 or 140 MHz IF (SW5) using the front panel

switches (Figure 2.1).

3. Select either HI or LOW GAIN using the switch (SW7) on the rear panel (Figure 2.2).

4. Connect a -10dBm max (LOW GAIN) or -25 dBm max (HI GAIN) signal to IF In, J1 (Figure 2.2).

5. Connect the RF OUT, J2, to the receiver under test (Figure 2.2).

6. Set BCD switches, SW1 to SW4, to the desired frequency (Figure 2.1).

7. Be sure DS1 (green, DC Power) is on and DS2 (red, Alarm) is off (Figure 2.1).

2005-10 Manual, Rev. B Page 6 4/28/09

2.6 Environmental Use Information

A.Rack-Mounting - To mount this equipment in a rack, please refer to the installation instructions

located in the user manual furnished by the manufacturer of your eqipment rack.

B. Mechanical loading - Mounting of equipment in a rack should be such that a hazardous condition

does not exist due to uneven weight distribution.

C.Elevated operating ambient temperature - If installed in a closed or multi-unit rack assembly,

the operating ambient temperature of the rack may be greater than room ambient temperature.

Therefore, consideration should be given to Tmra.

D. Reduced air flow - Installation of the equipment in a rack should be such that the amount of air flow

required for safe operation of the equipment is not compromised. Additional space between unit

may be required.

E. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply

circuit and the effect that overloading of circuits could have on over current protection and supply wiring.

Appropriate consideration of equipment name plate rating should be used, when addressing this concern.

F. Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular

attention should be given to supply connections other than direct connection to the Branch

(use of power strips).

G. Top Cover - There are no servicable parts inside the product so, the Top Cover should not be removed.

If the Top Cover is removed the ground strap and associated screw MUST BE RE-INSTALLED

prior to Top Cover screw replacement. FAILURE TO DO this may cause INGRESS and/or EGRESS

emission problems.

2005-10 Manual, Rev. B Page 7 4/28/09

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

2005-10 Manual, Rev. B Page 8 4/28/09

Table of contents

Other Cross Technologies Media Converter manuals

Cross Technologies

Cross Technologies 3117-3338 720 Series User manual

Cross Technologies

Cross Technologies 2117-9395 User manual

Cross Technologies

Cross Technologies 2016-8085 User manual

Cross Technologies

Cross Technologies 2117-7172 User manual

Cross Technologies

Cross Technologies 2017-03 User manual

Cross Technologies

Cross Technologies 2016-1522 User manual

Cross Technologies

Cross Technologies 2016-57 User manual

Cross Technologies

Cross Technologies 3116-145-1600 User manual

Cross Technologies

Cross Technologies 4115-41-212 User manual

Cross Technologies

Cross Technologies 2016-95 User manual

Cross Technologies

Cross Technologies 2416 02I Series User manual

Cross Technologies

Cross Technologies 2016-75-213 User manual

Cross Technologies

Cross Technologies 2116-116 User manual

Cross Technologies

Cross Technologies 2015-123 User manual

Cross Technologies

Cross Technologies 2016-05A User manual

Cross Technologies

Cross Technologies 3116-192 User manual

Cross Technologies

Cross Technologies 3016-1520-1200 User manual

Cross Technologies

Cross Technologies 2017-03A User manual

Cross Technologies

Cross Technologies 2415 0925 Series User manual

Cross Technologies

Cross Technologies 2415-02 Series User manual

Cross Technologies

Cross Technologies 1584 User manual

Cross Technologies

Cross Technologies 2016-03A User manual

Cross Technologies

Cross Technologies 2016-12 User manual

Cross Technologies

Cross Technologies 2117-8485 User manual

Popular Media Converter manuals by other brands

SoundTraxx

SoundTraxx Blunami BLU-2200 user guide

SPROLINK

SPROLINK VA1 user manual

Acclaim Lighting

Acclaim Lighting DDC-1-AC user guide

Nikon

Nikon AF-S TC-20E III user manual

Axis

Axis AXIS Q7406 user manual

Omega

Omega TAC80B-J instruction sheet

Zoom

Zoom Thunderbolt TAC-2R Operation manual

OST

OST iConverter 10/100M quick start guide

Vertiv

Vertiv Netsure user manual

birddog

birddog MINI user guide

Roland

Roland GI-10 owner's manual

Wallenstein

Wallenstein WX310 Operator's manual

Pace

Pace MSS 200-1 Service manual

Solar Converters

Solar Converters EQ 12/24-50 manual

CYP

CYP EL-7400V Operation manual

TIE

TIE MIDI 1i1o user manual

DCS

DCS Vivaldi Upsampler user manual

Westermo

Westermo MCW-211 SERIES user guide