Atdec TH-3060-UFL User manual

TH-3060-UFL Page 1 of 4

Installation Guide

TH-3060-UFL

Large-Medium

TV Articulated Arm

COMPONENT CHECKLIST

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! This product supports a maximum load of 35kg (77lbs).

! This product supports VESA mounting hole configurations 200mm wide x 100mm high to 700mm wide x 500mm high.

! The manufacturer accepts no responsibility for incorrect installation.

REQUIRED TOOLS

• Power drill

• 5mm (0.2”) drill bit

• 10mm (0.39”) masonry

drill bit

• Phillips head screw driver

• 13mm (0.5”) socket

wrench or shifter

Arm/Wall

Mount (x1)

Mounting Bracket

(x2)

Display

Mounting Screw

M8x25mm (x4)

Display

Mounting Screw

M8x16mm (x4)

Display

Mounting Screw

M6x25mm (x4)

Display

Mounting Screw

M6x16mm (x4)

5mm/4mm

Allen Key (x1)

End Cap (x2)

End Cap

Screw (x4)

Nylon Anchor

(x4)

Washer

(x4)

Multiwasher

(x4)

Coach Screw

(x4)

Top Cap (x2)

Locking Block (x2)

WEIGHT RANGE

0 - 35kg

(0 - 77lb)

TH-3060-UFL Page 2 of 4

Top Cap

SLIDE

1. Changing position of Arm on Wall Mount

Use Phillips head screw driver

to loosen and tighten.

Use 5mm Allen Key to

loosen and tighten.

Four optional positions

2. Install Arm/Wall Mount to the Wall

Coach Screw

Washer

End Cap

Screw

Nylon Anchor

Drilled Hole

End Cap

WALL Coach Screw

WasherEnd Cap

Screw Drilled Hole

End Cap

WALL

2.1 Masonry Wall

3. Attach Top Caps to the installed Arm/Wall Mount

Drill four 10mm (0.39”) diameter holes, 58mm (2.3”) deep.

Secure the mounting plate to the wall using the Coach.

Screws and Nylon Anchors supplied.

Drill four 5mm (0.2”) diameter holes, 58mm (2.3”) deep.

Secure the mounting plate to the wall using the Coach

Screws supplied.

Note: Use a stud nder to accurately locate the centre

of the stud. Ensure that all screws x securely into stud.

2.2 Timber Stud Wall

TH-3060-UFL Page 3 of 4

TOP

Back of Display

Display Mounting Screw

Multiwasher

Mounting Bracket

Locking Blocks

Back of Display

4. Attaching Mounting Brackets to Display

5. Attaching/Detaching Display to the installed Arm (2 people required)

WALL

Hook the

Display to

the Arm/

WallMount.

HOOK

LOCK

PUSH

DOWN

HOOK

Pull down both Spring Lock

Ties to open catch.

PULL

DOWN

PUSH

DOWN

RELEASE

The mounting brackets support hole congurations

from 200x100mm to 700x500mm.

6. Attach Locking Blocks to fully secure the Display

Release Spring Lock Ties

to secure Display.

Note: Ensure that Spring

Lock is fully engaged.

Push down Display into catch.

TH-3060-UFL Page 4 of 4

Back of Display

WALL

atdec.com | atdec.com.au

No portion of this document or any artwork contained herein should be reproduced in any way without

the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer

7. Adjust Arm movement if necessary

5mm Allen Key

4mm Allen Key

WALL

_90° +

_180°

_90°

Back of

Display

Socket Wrench

LOOSEN

TIGHTEN

(+kg)

(-kg)

-5°

+15°

_5°

8. Adjust tilt and roll if necessary

9. Cable Management

Position your display to the

desired viewing angle using the

angular movement allowed by

the double ball mount.

Depending on the weight of

the Display, it may be necessary

to make adjustments to the

double ball mount. If the display

does not hold its position, or is

too resistant, adjust the tension

plate located at the rear of the

double ball mount.

To adjust the tension plate,

apply half a turn at a time to

each nut. ENSURE NUTS ARE

ADJUSTED EVENLY.

CHECK THE DISPLAY, and then

adjust again if necessary.

Table of contents

Other Atdec Rack & Stand manuals

Atdec

Atdec TH-3060-UF User manual

Atdec

Atdec AWM-P G User manual

Atdec

Atdec AF-AN User manual

Atdec

Atdec AWM-LR User manual

Atdec

Atdec TH-1040-CTS User manual

Atdec

Atdec AWM-A13 User manual

Atdec

Atdec TH-PFK User manual

Atdec

Atdec AD-AC-PH User manual

Atdec

Atdec TH-2050-VFM User manual

Atdec

Atdec SPACEDEC ACROBAT Operation instructions

Atdec

Atdec Spacedec Acrobat Swing Arm Double User manual

Atdec

Atdec Visidec Focus Articulated Arm Wall Operation instructions

Atdec

Atdec AD-TVC-70A User manual

Atdec

Atdec Freestanding Quad User manual

Atdec

Atdec SYSTEMA SW6S User manual

Atdec

Atdec AWM-A46 User manual

Atdec

Atdec AF-M User manual

Atdec

Atdec VFS-Q User manual

Atdec

Atdec AF-AT User manual

Atdec

Atdec TELEHOOK 12/30 Multi User manual

Atdec

Atdec TH-1026-VF User manual

Atdec

Atdec Focus VF-AT-NP User manual

Atdec

Atdec AWMS-2-BT75-FS User manual

Atdec

Atdec AD-TVAC-CM User manual

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 