Atdec AWM-BT User manual

AWM-BT Page 1 of 2

Installation Guide

AWM-BT

COMPONENT CHECKLIST

Bracket

(x2)

VESA Plate

(x2)

M4x10

Screw

(x4)

M4x20

Screw

(x4)

10mm

Spacer

(4x)

4mm

Hex Key

(x1)

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! EachBracketsupportsamaximumweightasperabovecapacityspecication.

! Thisproductisnotsuitableforoutdooruse.

! Donotusethisproductformobileapplications.

! VESAmountedaccessories(suchasminiPCbracketsandmounts),andoffsetVESAlocationsexertadditionalleveragethatcan

exceedthecapacityofthemounteventhoughthemonitorweightmaybewithinthestatedrange.PleasecontactAtdecifyou

wouldlikefurtherinformation.

AWMTiltBracket

REQUIRED TOOLS

•PhillipsHeadScrewdriver

CAPACITY

Flat Monitor

4.5-25kg(10-55lb)

Curved Monitor

4.5-18kg(10-39lb)

300mm(12”)maxoverall

displaydepth

Screen Size

24”-55”

AWM-BT Page 2 of 2

2. SlideBracketontoPost,SetHeightandMountDisplay

1.1 VESAmountcompatibility

1. AttachVESAPlatetoDisplay

75mm

100mm

75mm

100mm

NOTE:

For 75mm

VESA unscrew

5mm to access

top holes A

1.2 AttachVESAPlatewith

M4x10Screws.

TOP

WARNING:

Do not loosen

hand knob once

display mounted�

2.3 SetVESAPlateto

openposition.

2.4 LiftdisplayuntilVESA

Plateisabovetheheightof

theBracket.

2.5 WithPostcentered,

slowlylowerdisplayuntil

baronVESAPlatesitsin

saddleinBracket.

2.6SetVESAPlate

to closedposition

byslidingclipson

bothsidesinwards.

3. FineAdjustment

Noportionofthisdocumentoranyartworkcontainedhereinshouldbereproducedinanywaywithout

theexpresswrittenconsentofAtdecPtyLtd.Duetocontinuingproductdevelopment,themanufacturer

2.2Firmlytighten

handknobatchosen

height.

AWM POST

(not supplied)

Arrow side

towards user

TIGHTEN

OPEN

2.7Adjustdisplay

tiltanglebygripping

edgesofscreenand

rollingupordownto

desiredposition.

2.8Tightentiltknobs

tosetdisplayangle.

ORForrecessedVESAuse10mm

SpacersandM4x20Screws.

AWM POST

(not supplied)

Arrow side

towards user

OPEN

CLOSED

3.1Tocorrecthorizontalangleof

display+/-3°:

Turnasingleneadjustmentknob

toadjustangleofscreen.

3.2Toclosesmallgapbetweendisplays

+/-6mm(1/4”):

Turnbothneadjustmentknobs-

alternatingsidesafewrotationsatatime.

Clockwise=Higher

Anti-clockwise=Lower

FINE HEIGHT ADJUST

FINE ADJUSTMENT

KNOBS

NOTE:

Ensure slide clips in

CLOSED position after

ﬁne adjustment complete

2.1Lineuptheinnerguide

onrearofBracketwith

rearchannelonPost.

Slideinnerguideinto

channeland

lowerBracket.

Clockwise = More friction

Anti-clockwise = Less friction

OPTIONAL ADJUSTMENT

- TILT FRICTION

4mm Hex Key can be used

to reduce tilt friction (for

light screen) or increase tilt

friction (for heavy screen).

TILT

KNOBS

CLOSED

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 