Atdec SD-AT-DW User manual

SD-AT-DW Page 1 of 4

Installation Guide

SD-AT-DW

Wall Full Motion Mount

COMPONENT CHECKLIST

REQUIRED TOOLS

Articulated

Arm Assembly

(x1)

16mm Cable

Wrap

(x1)

Direct Wall Mount

Bracket Assembly

(x1)

Cable Wrap

Applicator

(x1)

Cable Clip

(x3)

M6 Washer

(x4)

Nylon

Archor Plugs

(x4)

M6x40

Coach Screw

(x4)

Extension

Clip

(x4)

2.5/5mm

Allen Key

(x1 each)

Top Cap

Tool

(x1)

Mounting Screw

M4x16mm

(x4)

Mounting Screw

M4x12mm

(x4)

Mounting Screw

M4x10mm

(x4)

• Phillips Head Screwdriver

WEIGHT RANGE

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! This mount supports a maximum weight of 3kg to 9kg (6.6lbs to 19.8lbs).

! This product supports VESA mounting hole configurations: 75x75mm and 100x100mm.

! The manufacturer accepts no responsibility for incorrect installation.

! Curved monitors, deep devices (such as all-in-one PCs) and offset VESA locations exert additional leverage that can

exceed the capacity of the mount even though the monitor weight may be within the stated range. Please contact

Atdec if you would like further information.

3 - 9kg

6.6 - 19.8lbs

SD-AT-DW Page 2 of 4

Display

4x10mm

Screws

75mm

1. Direct Wall Mount

3. Attaching the Display

2. Mount Arm to Wall Bracket

1.1 Refer to Ergonomic

guidelines overleaf to

determine best position

to mount wall bracket.

OPTION A 75x75mm VESA mount

75mm x 75mm mounting hole pattern

OPTION B 100x100mm VESA mount

100mm x 100mm mounting hole pattern

2.1 Attach the Arm to the

Direct Wall Mount Bracket.

Tighten the Top Cap with

the supplied Top Cap Tool.

1.2 For Timber Stud Mounting - Use the Direct

Wall Mount Bracket to mark out the location

of the required four holes. (see Step 1.1) Drill

4mm holes deep enough to receive the M6

Coach Screws, insert the screws and secure the

bracket to the wall.

1.3 For Masonry Mounting - Use the Direct

Wall Mount Bracket to mark the location

of the required four holes. (see Step 1.1)

Using an 8mm masonry drill bit, drill four

holes 41mm deep. Insert the Nylon Anchors

and then secure the Bracket to the wall using

the M6 Coach Screws.

Front View of the Direct

Wall Mount Bracket

Note Ensure Bracket

is mounted Vertically.

1 2

3 4

Timber Stud

Wall

Direct Wall

Mount Bracket

4mm Hole

M6 Washer

M6 Coach Screw

Tighten

using the

Top Cap Tool

Insert

Threaded

Rod and

Top Cap

Direct Wall

Mount Bracket

Plastic Bottom Cap

Arm with

inner tube

Brick or Concrete Wall

S8 Nylon Anchor

M6 Coach Screw

8mm Hole

Direct Wall

Mount Bracket

M6 Washer

2.2 Tighten

TIGHTEN

Extension Clip

4x12mm or

4x16mm Screws

100mm

Display

Note Ensure that the flat

side of each extension

clip sits against the back

of the display.

SD-AT-DW Page 3 of 4

4. Installing Cable Management

5. Attaching the Cable Wrap to the arm

Position the display at its highest possible position to

ensure that there is sufficient cabling at the end of the

arm so the cables are not stretched or pulled out when

the display is moved.

6. Ergonomic Guidelines

6.1 Recommended Mounting position

When mounting the Wall Full Motion

Mount, ensure the correct focal distance

can be achieved for ultimate visual comfort

(refer to recommended Viewing Distance /

Height below)

Wall Mount

15°

5°

Horizontal

sight line (d)

Centre of screen

10°-20°

(h)

6.2 Recommended Viewing Distance/ Height

a. Ergonomists recommend that the optimal position of your screen should be

slightly below eye level. When looking at the screen’s centre the user should

have a downward visual angle of approximately 10°-20°. As a guide, the height

(h) of your display should approximately be as follows:

b. For visual comfort, a viewing distance (d) between 500mm (191/2”) to

750mm (291/2”) is recommended.

c. Angular adjustments to reduce reflection on your monitor should range

between 5° forward tilt to 15° backward tilt.

• Tall Male (Max): 560mm (22”)

• Short Male (Min): 368mm (141/2”)

• Tall Female (Max): 520mm (201/2”)

• Short Female (Min): 356mm (14”)

4.1 Push the three supplied

Cable Clips into the holes on the

underside of the arm as shown.

4.2 Feed the cables

into the Cable Wrap

Applicator.

4.3 Insert the Cable Wrap

Applicator into the Cable

Wrap as shown.

4.4 Squeeze the nose of the Applicator

and place inside the Cable Wrap

ensuring that the opening edges of the

Cable Wrap face towards the nose of

the applicator as shown in diagram.

Push in

Clips

Cable Clips (x3)

Display at

highest point

Nose

SD-AT-DW Page 4 of 4

TIGHTEN

LOOSEN

Tension

Screws (X4)

Ball Joint

2.5mm

Allen Key

TIGHTEN

LOOSEN

Pivot Head

Interscrew

5mm Allen Key

3kg

Display

9kg

Display

5mm

Allen Key

Arm

Gas Strut

Raise Gas

Strut to suit

lighter display

Lower Gas Strut

to suit heavier display

LIGHTER

HEAVIER

No portion of this document or any artwork contained herein should be reproduced in any way without

the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer

7. Adjusting the Display

The Wall Full Motion Mount comes factory set to support 6kg displays. Adjust the arm to suit the weight of your

display as shown in the following steps:

7.2 Adjusting the Pivot Head Resistance

It is possible to control the amount of resistance in the Pivot

Head to suit your display.

To increase the resistance of the Pivot Head to suit heavier

displays, use the 5mm Allen Key supplied in the Desk Clamp

Box to tighten the interscrew in a clockwise direction.

To decrease the resistance of the Pivot Head to suit lighter

displays, loosen the interscrew in an anti-clockwise direction.

Note It is recommended the Pivot Head be left at the factory

setting for best performance.

7.1 Adjusting the Ball Joint Resistance

Depending on the weight of the display, it may be necessary

to make adjustments to the Ball Joint Mechanism. If the

display doesn’t hold its position or is too resistant, adjust

the four tension screws located around the Ball Joint (see

diagram on the right) using the supplied 2.5mm Allen Key.

Check the display, and then adjust again if necessary.

Note Be sure to adjust screws evenly.

7.3 Adjusting the Full Motion Mount/Gas Strut Resistance

a. Depending on the weight of the display, it may be

necessary to adjust the arm. This can be done by using the

5mm Allen Key supplied in the Desk Clamp Box.

b. If the arm tends to automatically rise or fall when the

display is attached, it will be necessary to make small

adjustments to the gas strut. (see diagram on the right)

c. If the arm tends to rise, the gas strut position should be

raised. If the arm tends to fall, the gas strut position should

be lowered.

Before Proceeding to the next step please note

Wall Full Motion Mount will only work when a display is properly installed.

Do not adjust tension screws or gas strut until your display has been attached.

Other Atdec Rack & Stand manuals

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 