Anritsu MP1800A User manual

Document No.: M-W2747AE-18.0

ANRITSU CORPORATION

MP1800A

Signal Quality Analyzer

Installation Guide

For safety and warning information, please read

this

manual before attempting to use the equipment.

Keep this manual with the equipment.

18th Edition

Safety Symbols

To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the

following safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings of

the symbols BEFORE using the equipment. Some or all of the following symbols may be used on all Anritsu

equipment. In addition, there may be other labels attached to products that are not shown in the diagrams in this

manual.

Symbols used in manual

This indicates a very dangerous procedure that could result in serious injury or

death if not performed properly.

This indicates a hazardous procedure that could result in serious injury or death if

not performed properly.

This indicates a hazardous procedure or danger that could result in light-to-severe

injury, or loss related to equipment malfunction, if proper precautions are not taken.

Safety Symbols Used on Equipment and in Manual

The following safety symbols are used inside or on the equipment near operation locations to provide information

about safety items and operation precautions. Ensure that you clearly understand the meanings of the symbols and

take the necessary precautions BEFORE using the equipment.

This indicates a prohibited operation. The prohibited operation is indicated

symbolically in or near the barred circle.

This indicates an obligatory safety precaution. The obligatory operation is

indicated symbolically in or near the circle.

This indicates a warning or caution. The contents are indicated symbolically in or

near the triangle.

This indicates a note. The contents are described in the box.

These indicate that the marked part should be recycled.

MP1800A

Signal Quality Analyzer

Installation Guide

27 November 2006 (First Edition)

25 August 2020 (18th Edition)

publisher.

The operational instructions of this manual may be changed without prior notice.

Printed in Japan

DANGER

WARNING

CAUTION

For Safety

iii

WARNING

•ALWAYS refer to the operation manual when working near locations

at which the alert mark shown on the left is attached. If the advice in

the operation manual is not followed, there is a risk of personal injury

or reduced equipment performance. The alert mark shown on the left

may also be used with other marks and descriptions to indicate other

dangers.

•Overvoltage Category

This equipment complies with overvoltage category II defined in IEC

61010. DO NOT connect this equipment to the power supply of

overvoltage category III or IV.

•Laser radiation warning

- NEVER look directly into the cable connector on the equipment

nor into the end of a cable connected to the equipment. There is a

risk of injury if laser radiation enters the eye.

- The Laser Safety label is attached to the equipment for safety use

as indicated in "Laser Safety" later in this section.

•To ensure that the equipment is grounded, always use the supplied

3-pin power cord, and insert the plug into an outlet with a ground

terminal. If power is supplied without grounding the equipment, there

is a risk of receiving a severe or fatal electric shock or causing

damage to the internal components.

Electric Shock

For Safety

WARNING

•Only qualified service personnel with a knowledge of electrical fire and

shock hazards should service this equipment. This equipment cannot

be repaired by the operator. DO NOT attempt to remove the

equipment covers or unit covers or to disassemble internal

components. There are high-voltage parts in this equipment

presenting a risk of severe injury or fatal electric shock to untrained

personnel. In addition, there is a risk of damage to precision

components.

•The performance-guarantee seal verifies the integrity of the equipment.

To ensure the continued integrity of the equipment, only Anritsu

service personnel, or service personnel of an Anritsu sales

representative, should break this seal to repair or calibrate the

equipment. Be careful not to break the seal by opening the

equipment or unit covers.If the performance-guarantee seal is

broken by you or a third party, the performance of the equipment

cannot be guaranteed.

•This equipment should always be positioned in the correct manner. If

the cabinet is turned on its side, etc., it will be unstable and may be

damaged if it falls over as a result of receiving a slight mechanical

shock.

Always set up the equipment in a position where the power switch

can be reached without difficulty.

•This equipment uses a Liquid Crystal Display (LCD). DO NOT subject

the equipment to excessive force or drop it. If the LCD is subjected to

strong mechanical shock, it may break and liquid may leak.

This liquid is very caustic and poisonous.

DO NOT touch it, ingest it, or get in your eyes. If it is ingested

accidentally, spit it out immediately, rinse your mouth with water and

seek medical help. If it enters your eyes accidentally, do not rub your

eyes, rinse them with clean running water and seek medical help. If

the liquid gets on your skin or clothes, wash it off carefully and

thoroughly with soap and water.

Falling Over

Calibration

LCD

Repair

For Safety

CAUTION

•Always remove the main power cable from the power outlet before

cleaning dust around the power supply and fan.

- Clean the power inlet regularly. If dust accumulates around the

power pins, there is a risk of fire.

- Keep the cooling fan clean so that the ventilation holes are not

obstructed. If the ventilation is obstructed, the cabinet may

overheat and catch fire.

•Never input a signal of more than the indicated value between the

measured terminal and ground. Input of an excessive signal may

damage the equipment.

•This is a heavy object. When lifting and moving this equipment,

always work in a group of two or more, or use a trolley. There is a

risk of back injury, if this equipment is lifted or moved by one person.

Cleaning

Check Terminal

For Safety

Class 1 indicates the danger degree of the laser radiation specified

below according to IEC 60825-1:2007.

Class 1: Lasers that are safe under reasonably foreseeable

conditions of operation, including the use of optical

instruments for intrabeam viewing.

CAUTION

Use of controls or adjustments or performance of procedures other than

those specified herein may result in hazardous radiation exposure.

The use of optical instruments with this product will increase eye

hazard.

For Safety

vii

The laser in this equipment is classified as Class 1 according to the IEC

60825-1:2007 standard.

Table 1 Laser Safety Classifications Based on IEC 60825-1:2007

Model Name

Reco

mmende

d Module

Model Name

or Option

Model

Name/Part

Name

Class

Max. Optical

Output Power

(mW)

Pulse Width

(s)/Rep

-etition

Rate

Emitted

Wave-

length (nm)

Beam

Diverg

ence

(deg)

Laser

Aperture

MU181600A

G0174A

850 nm XFP module 1 0.78 CW 840-860 36.9 Fig. 2,

[1]

G0175A

1310 nm XFP module 1 0.8 CW 1290-1330 11.5 Fig. 2,

[1]

G0176A

1550 nm XFP module 1 1.58 CW 1530-1565 11.5 Fig. 2,

[1]

MU181601A

G0177A

850 nm SFP module 1 0.56 CW 830-860 36.9 Fig. 3,

[1]

G0178A

1310 nm SFP module 1 1.0 CW 1270-1360 11.5 Fig. 3,

[1]

G0179A

1550 nm SFP module 1 1.0 CW 1430-1590 11.5 Fig. 3,

[1]

MU181620A

Optionx01

1310nm Reference 1 5.0 CW 1290-1330 11.5 Fig. 4,

[1]

Optionx02

1550nm Reference 1 5.0 CW 1530-1565 11.5 Fig. 4,

[1]

Optionx03

1310nm/1550nm

Reference 1 5.0 CW 1290-1330

1530-1565＊211.5 Fig. 4,

[1]

Optionx11

1310nm Stressed

Eye 1 5.0 CW 1290-1330 11.5 Fig. 4,

[1]

Optionx12

1550nm Stressed

Eye 1 5.0 CW 1530-1565 11.5 Fig. 4,

[1]

Optionx13

1310nm/1550nm

Stressed Eye 1 5.0 CW 1290-1330

1530-1565＊211.5 Fig. 4,

[1]

*1: Indicates the possible optical output power when each and every

reasonably foreseeable single-fault condition is included.

*2: A light of either wavelength will be emitted.

Laser Safety

For Safety

viii

Table 2 Incorporated Laser Specification

Model Name

Recommended

Module Model

Name or Op

tion

Model Name/Part

Name

Max. Optical

Output Power

(mW)*1

Pulse Width

(s)/Rep

-etition

Rate

Emitted Wave

length (nm)

Beam

Divergence (d

eg)

MU181600A

G0174A

850 nm XFP module 0.78 CW 840-860 36.9

G0175A

1310 nm XFP module 0.8 CW 1290-1330 11.5

G0176A

1550 nm XFP module 1.58 CW 1530-1565 11.5

MU181601A

G0177A

850 nm SFP module 0.56 CW 830-860 36.9

G0178A

1310 nm SFP module 1.0 CW 1270-1360 11.5

G0179A

1550 nm SFP module 1.0 CW 1430-1590 11.5

MU181620A

Optionx01

1310nm Reference 5.0 CW 1290-1330 11.5

Optionx02

1550nm Reference 5.0 CW 1530-1565 11.5

Optionx03

1310nm/1550nm

Reference 5.0 CW 1290-1330

1530-1565＊211.5

Optionx11

1310nm Stressed

Eye 5.0 CW 1290-1330 11.5

Optionx12

1550nm Stressed

Eye 5.0 CW 1530-1565 11.5

Optionx13

1310nm/1550nm

Stressed Eye 5.0 CW 1290-1330

1530-1565＊211.5

*1: Indicates the possible optical output power when each and every

reasonably foreseeable single-fault condition is included.

*2: A light of either wavelength will be emitted.

For Safety

Table3Labels on Product

Type Label Affixed

to: Model Name

1 Explanation Fig. 1, A MP1800A

2 Certification Fig. 1, B MP1800A

3 Identification Fig. 1, C MP1800A

4 Explanation Fig. 2, A

Fig. 3, A MU181600A

MU181601A

5 Explanation Fig. 4, A MU181620A

For Safety

Laser Radiation Markings

Figure 1 MP1800A Exterior

Other manuals for MP1800A

Table of contents

Other Anritsu Measuring Instrument manuals

Anritsu

Anritsu ShockLine MS46522A User manual

Anritsu

Anritsu MP1570A User manual

Anritsu

Anritsu Site Master S113B User manual

Anritsu

Anritsu MT9085 Series Instruction manual

Anritsu

Anritsu BTS Master MT8220T User manual

Anritsu

Anritsu ML2437A Owner's manual

Anritsu

Anritsu Spectrum Master MS2721A User manual

Anritsu

Anritsu 3656C W1 User manual

Anritsu

Anritsu VectorStar ME7828A Series User manual

Anritsu

Anritsu MT9083B2 User manual

Anritsu

Anritsu BTS Master MT8220T Owner's manual

Anritsu

Anritsu MG9637A User manual

Anritsu

Anritsu MS2070A User manual

Anritsu

Anritsu Site Master S113BQ User manual

Anritsu

Anritsu 54100A Series Installation and operating instructions

Anritsu

Anritsu MU196020A PAM4 PPG User manual

Anritsu

Anritsu MT1100A Network Master Flex User manual

Anritsu

Anritsu VectorStar MS4640A Series User manual

Anritsu

Anritsu MS2720 A Series User manual

Anritsu

Anritsu MT8801C User manual

Anritsu

Anritsu MS2690A User manual

Anritsu

Anritsu VectorStar ME7848A Series User manual

Anritsu

Anritsu MP1800A User manual

Anritsu

Anritsu Network Master MU909020A User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual