Anritsu Network Master Series User manual

Document No.: M-W2988AE-13.0

Network Master Series

MT9090A

Mainframe

MU909011A

Drop Cable Fault Locator Module

Operation Manual

13th Edition

For safety and warning information, please read this

manual before attempting to use the equipment.

Keep this manual with the equipment.

ANRITSU CORPORATION

ii MT9090A/MU909011A Network Master User’s Guide

8 October 2007 (First Edition)

20 February2015 (13th Edition)

This document and the product to which it relates are

protected by copyright law from unauthorized reproduction.

Notice to U.S. Government End Users

The Software and Documentation are “Commercial Items,”

as that term is defined at 48 C.F.R. 2.101, consisting of

“Commercial Computer Software” and “Commercial

Computer Software Documentation,” as such terms are used

in 48 C.F.R. 12.212 or 48 C.F.R. 227.7202, as applicable.

Consistent with 48 C.F.R. 12.212 or 48 C.F.R. 227.7202-1

through 227.7202-4, as applicable, the Commercial

Computer Software and Commercial Computer Software

Documentation are being licensed to the U.S. Government

end users (a) only as Commercial Items and (b) with only

those rights as are granted to all other end users pursuant to

the terms and conditions herein. Unpublished rights reserved

under the copyright laws of the United States.

•The contents of this manual may be changed

without prior notice.

•No part of this manual may be reproduced without

the prior written permission of the publisher.

MT9090A/MU909011A Network Master User’s Guide iii

Safety Symbols

To prevent the risk of personal injury or loss related to

equipment malfunction, Anritsu Corporation uses the

following safety symbols to indicate safety-related

information. Ensure that you clearly understand the

meanings of the symbols BEFORE using the equipment.

Some or all of the following symbols may be used on all

Anritsu equipment. In addition, there may be other labels

attached to products that are not shown in the diagrams in

this manual.

Symbols used in manual

DANGER This indicates a very dangerous procedure

that could result in serious injury or death

if not performed properly.

WARNING This indicates a hazardous procedure that

could result in serious injury or death if

not performed properly.

CAUTION This indicates a hazardous procedure or

danger that could result in light-to-severe

injury, or loss related to equipment

malfunction, if proper precautions are not

taken.

iv MT9090A/MU909011A Network Master User’s Guide

Safety Symbols Used on Equipment and in

Manual

The following safety symbols are used inside or on the

equipment near operation locations to provide information

about safety items and operation precautions. Ensure that

you clearly understand the meanings of the symbols and take

the necessary precautions BEFORE using the equipment.

This indicates a prohibited operation. The

prohibited operation is indicated symbolically

in or near the barred circle.

This indicates an obligatory safety precaution.

The obligatory operation is indicated

symbolically in or near the circle.

This indicates a warning or caution. The

contents are indicated symbolically in or near

the triangle.

This indicates a note. The contents are

described in the box.

These indicate that the marked part should be

recycled.

MT9090A/MU909011A Network Master User’s Guide v

For Safety

WARNING !

•ALWAYS refer to the Operation

Manual when working near

locations at which the alert mark

shown on the left is attached. If

the advice in the Operation

Manual is not followed there is a

risk of personal injury or

reduced equipment

performance. The alert mark

shown on the left may also be

used with other marks and

descriptions to indicate other

dangers.

•Overvoltage Category

This equipment complies with

overvoltage category II defined

in IEC 61010. DO NOT

connect this equipment to the

power supply of overvoltage

category III or IV.

vi MT9090A/MU909011A Network Master User’s Guide

•Laser radiation warning

•NEVER look directly into

the cable connector on the

equipment nor into the end

of a cable connected to the

equipment. There is a risk

of injury if laser radiation

enters the eye.

•The Laser Safety label is

attached to the equipment

for safety use as indicated in

“Laser Radiation Markings

and Laser Aperture” on

page xiv.

Repair •Only qualified service personnel

with a knowledge of electrical

fire and shock hazards should

service this equipment. This

equipment cannot be repaired

by the operator. DO NOT

attempt to remove the

equipment covers or unit covers

or to disassemble internal

components. There are high-

voltage parts in this equipment

presenting a risk of severe injury

or fatal electric shock to

untrained personnel. In

addition, there is a risk of

damage to precision

components.

MT9090A/MU909011A Network Master User’s Guide vii

Calibration •he performance-guarantee seal

verifies the integrity of the

equipment. To ensure the

continued integrity of the

equipment, only Anritsu service

personnel, or service personnel

of an Anritsu sales

representative, should break this

seal to repair or calibrate the

equipment. Be careful not to

break the seal by opening the

equipment or unit covers.If the

performance-guarantee seal is

broken by you or a third party,

the performance of the

equipment cannot be

guaranteed.

Replacing

Battery

•When replacing the battery, use

the specified battery and insert it

with the correct polarity. If the

wrong battery is used, or if the

battery is inserted with reversed

polarity, there is a risk of

explosion causing severe injury

or death.

viii MT9090A/MU909011A Network Master User’s Guide

Battery Fluid •DO NOT short the battery

terminals and never attempt to

disassemble the battery or

dispose of it in a fire. If the

battery is damaged by any of

these actions, the battery fluid

may leak. This fluid is

poisonous.

DO NOT touch the battery

fluid, ingest it, or get in your

eyes. If it is accidentally

ingested, spit it out immediately,

rinse your mouth with water and

seek medical help. If it enters

your eyes accidentally, do not

rub your eyes, rinse them with

clean running water and seek

medical help. If the liquid gets

on your skin or clothes, wash it

off carefully and thoroughly.

Battery

Disposal

•DO NOT expose batteries to

heat or fire. Do not expose

batteries to fire. This is

dangerous and can result in

explosions or fire. Heating

batteries may cause them to leak

or explode.

MT9090A/MU909011A Network Master User’s Guide ix

Laser Safety

Class 1and 3R indicate the danger degree of laser radiation

specified below according to IEC 60825-1:2007.

LCD •This instrument uses a Liquid

Crystal Display (LCD). DO

NOT subject the instrument to

excessive force or drop it. If the

LCD is subjected to strong

mechanical shock, it may break

and liquid may leak.

This liquid is very caustic and

poisonous.

DO NOT touch it, ingest it, or

get in your eyes. If it is ingested

accidentally, spit it out

immediately, rinse your mouth

with water and seek medical

help. If it enters your eyes

accidentally, do not rub your

eyes, rinse them with clean

running water and seek medical

help. If the liquid gets on your

skin or clothes, wash it off

carefully and thoroughly.

Class 1: Lasers that are safe under reasonably foreseeable

conditions of operation, including the use of

optical instruments for intrabeam viewing.

x MT9090A/MU909011A Network Master User’s Guide

CAUTION !

Use of controls or adjustments or performance of

procedures other than those specified herein may result

in hazardous radiation exposure.

The use of optical instruments with this product will

increase eye hazard.

Class 3R: Lasers that emit in the wavelength range from

302.5 to 106nm where direct intrabeam

viewing is potentially hazardous but the risk is

lower than for Class 3B lasers.

Other manuals for Network Master Series

This manual suits for next models

Other Anritsu Measuring Instrument manuals

Anritsu

Anritsu VectorStar ME7838E4X User manual

Anritsu

Anritsu MS9740A User manual

Anritsu

Anritsu MS2722C User manual

Anritsu

Anritsu MT1810A User manual

Anritsu

Anritsu ShockLine MS46522A User manual

Anritsu

Anritsu MS2690A User manual

Anritsu

Anritsu MU182020A User manual

Anritsu

Anritsu VectorStar ME7838 4X Series User manual

Anritsu

Anritsu ML2400A Series User manual

Anritsu

Anritsu Spectrum Master MS2711D Owner's manual

Anritsu

Anritsu Lightning 37 E Series User manual

Anritsu

Anritsu Spectrum Master MS2711E User manual

Anritsu

Anritsu Microwave Site Master S820E User manual

Anritsu

Anritsu MS2024A/MS2026A User manual

Anritsu

Anritsu Field Master MS2080A User manual

Anritsu

Anritsu 54100A Series Installation and operating instructions

Anritsu

Anritsu MP1800A User manual

Anritsu

Anritsu MP1570A User manual

Anritsu

Anritsu MS2690A User manual

Anritsu

Anritsu Spectrum Master MS2720T User manual

Anritsu

Anritsu ShockLine MS46322A Series User manual

Anritsu

Anritsu Field Master MS2070A-703 User manual

Anritsu

Anritsu MX269017A User manual

Anritsu

Anritsu VNA Master MS2026C Owner's manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual