Amcor AMB12KE410A User manual

ENGLISH INSTRUCTION MANUAL

AMB12

• PORTABLE AIR CONDITIONER

AMB

12KE410A

For safety reasons, please read this manual

carefully before operating.

Persons who are not familiar with this manual

must not use this dehumidifier.

We strongly recommend keeping this manual in a

safe place for future reference.

Warning: Never operate this appliance if it has

a damaged cord or plug.

If the supply cord is damaged, it must be replaced

by an approved service representative or a

similar qualified person in order to avoid the risk

of injury.

This appliance is not intended for use by young

children or infirm persons without supervision.

Young children should be supervised to ensure

that they do not play with this appliance.

This appliance should be installed at least 50

centimetres clear of any structure.

The minimum clearance this appliance and any

combustible surface is 50 centimetres.

Do not place anything on top of the appliance,

e.g. clothing.

GENERAL SAFETY

Do not place in front of an open

window.

Do not clamp or bend the cable.

Do not immerse in water.

Do not insert anything.

Do not place near a heat source.

Do not place unevenly.

Do not use a damaged cable.

Do not bring in contact with

chemicals.

Do not use an extension cord.

Do not spill.

Do not repair. Keep out of the reach of children.

Warning: This appliance must be earthed. For

voltage and power input refer to the rating plate.

This appliance is supplied with an electrical cable

and an earthed plug. Should it be necessary

to replace this plug at any time, you must use

an earthed plug and wire as shown on page 3

opposite.

If the attached plug is unsuitable cut it off and

throw it away.

NEVER insert the severed plug into an electrical

socket or outlet. Never use the plug without the

fuse cover fitted in place. The replacement fuse is

13 Amps and should conform to BS1362.

PLUG / FUSE REPLACEMENT

1. Control panel

2. Cooling air outlet

3. Handle

4. Casters

5. Air filter

6. Air inlet

7. Exhaust air outlet

8. Cord hanger

9. Water stopper (rubber plug inside)

Parts

PVC suction cups

PVC tube

Nylon strip

Adjustable

spring stopper

10. Hose adapters

11. Exhaust hose

12. Foam strip (hole for connection to the exhaust hose)

13. Round window connector

14. Cap for round window connector

15. Water tray

16. Remote control

17. Water tube

18. Window fitting kit

Plug / fuse replacement (continued from page 2)

13 Amp

13 A fuse

Brown

(Live)

Yellow/Green

(Earth)

Blue

(Neutral) Cable grip

The wires of the cable are colour-coded in accordance with

the standard electrical code.

• The BLUE (Neutral) wire should be connected to the

terminal in the plug marked N or coloured black.

• The BROWN (Live) wire should be connected to the

terminal in the plug marked L or coloured red.

• The YELLOW/GREEN (Earth) wire should be connected

to the terminal in the plug marked E or coloured green.

It is important that you read these instructions before using your new portable air

conditioner. We strongly recommend that you keep these instructions in a safe

place for future reference.

Warning: Before using the air conditioner it should be left in an upright

position for at least 2 hours.

Thank you for choosing this air conditioner from AMCOR - a leading name in air

treatment.

For over 50 years, AMCOR has specialised in complete indoor environment

control, manufacturing portable air conditioners, coolers, air purifiers, ionisers,

dehumidifiers and aromatherapy products.

These world class products incorporate the latest technological developments and

are designed to create a quality environment.

The unit is designed for indoor operation.

Rating: This unit must be connected to a 220-240 V / 50 Hz earthed outlet. The

installation must be in accordance with regulations of the country where the unit is

used.

If you are in any doubt about the electrical installation, have it checked and if

necessary modified by a qualified electrician.

• The air conditioner is safe. However, as with other electrical appliances, use it

with care.

• Do not clean the air conditioner by spraying it or immersing it in water.

• Do not insert any object into the opening of the air conditioner.

• Disconnect from the mains before cleaning the unit or any of its components.

• Never connect to an electrical outlet using an extension cord. If an outlet is not

available, one should be installed by a licensed electrician.

• Any service other than regular cleaning or filter replacement should be

performed by an authorized service representative.

Failure to do so could result in a loss of warranty.

WARNING Never operate this appliance if it has a damaged cord

or plug. Do not lead the cord over sharp edges.

Instruction manual

Thank you!

Safety instructions

Installation

Instruction manual

This unit is a portable air conditioner. It can be moved from room to room so that

the cooling can follow you anywhere. Fitting the exhaust hose is easy, through a

window or wall. Please refer to either of the following ways:

Important

The supplied flexible exhaust hose can be extended from 300 to 1500 mm for

locating. It is recommended that you use the shortest possible length of the hose.

This length has been designed especially according to the specifications of the air

conditioner. Do not replace or extend it with your own hoses as this could cause

the unit to malfunctioning.

The exhaust air must flow freely, any blockage can lead to overheating of the air

conditioner. Take care to prevent any kink or bend in the middle of the exhaust

hose, as this will trap hot exhaust air, which will radiate into the room.

Safety instructions

Installation

Using the foam strips.

• Open the window.

• Moisten the suction cups from the window

fitting kit (18) and press firmly onto a clean

window to secure.

• Place the connector (13) into the hole in the

foam (12) with the flange outside.

• Screw the end of the hose (11) into the

fitting (13).

• Place the assembled foam strip between the

open window and pull the windows so that

they close onto the foam.

• Depress the button on the toggle and pull

the cord until it is taught.

• Release the button to enable the cord to

hold the foam in place.

• Connect the hose to the back of the unit

with the adapter (10).

• Pass the hose through the opening in the

foam (12)

Using the round window connector.

• Make a hole in the wall/glass large enough

to fit the supplied round connector (13) with

the flange on the inside.

• Fit the hose (11) directly to the round

connector.

• When the hose is not in use, place the cap

(14) to cover the hole.

ON/OFF

Press button the unit will start to work at the last setting. If the wall

socket is switched off, the unit defaults to the factory setting. To turn the unit

off, press the button again.

Timer button

Press the button to set the operating hours (1 to 12 hours, the timer

LED will light up). When the set time has elapsed, the unit will turn off

automatically. The display will show the hour(s) you set as you press the

button. If the button is not pressed, the unit will work continuously.

By pressing the button without turning on the unit, you can PRE-SET the

time for the unit to work. For example, if you press the timer to '2', the unit

will come on automatically after 2 hours.

Mode button

Press the button to select the required working mode: automatic, co or

The LED illustrating your selected mode lights up: AUTO, or .

AUTO mode

• higher than 23 °C, the unit will work in cooling mode.

• higher than 20 °C but below or equal to 23 °C, the unit will work in

ventilation mode.

Indicators of the functions in progress come on at the same time, e.g. and

i.e. cooling with low fan speed.

Fan speed button

Press the button to choose the fan speed you require, high or low .

The LED will light up at the same time.

Operation

If the unit is in AUTO mode, it will select the fan speed automatically

according to the ambient temperature (the related LED will light up), at this

time the fan speed button is inoperative.

Temperature selection

Press the or button to select the temperature you desire (ranging

from 18 °C to 32 °C).

The display will show the temperature you set as you press the

or button. Otherwise, it will always display the ambient

temperature .

The pre-set room temperature of this unit is higher than 23 °C for cooling.

Sleep mode

This mode can only be used when cooling is selected. Press the button.

Every hour the temperature will rise with 1 °C, to a maximum of 2 °C. After

12 hours the unit will switch off automatically. Press the button again to

cancel sleep mode. In the sleep mode the set temperature can not be changed.

Remote control

All the above functions can also be performed with the supplied remote

control. This remote control requires 2 AAA-batteries to operate.

Notice!

• To prolong the unit's life, it will start 3 minutes after the unit was switched on.

After switching off, please wait at least 3 minutes before switching it on again.

• The cooling will switch off when the room temperature is lower than the set one.

The fan, however, keeps working at the set level. If the ambient temperature

rises above the chosen value, the cooling will resume.

Turn the roller on the air vent

to control the air flow direction

from the vertical louvres.

Move the air vent directly to

adjust the air flow direction

from the horizontal louvres.

Regulating the air flow direction.

During the process of cooling, some water

will be extracted from the air into the unit. If

the water container inside the unit is full, the

unit will stop, the fan will continue to circulate

the air. The POWER-LED will blink to inform you

to empty the internal container. To make the

cooling function work again, please empty the

water by one of the following methods:

By the supplied water tray.

1. Turn OFF the unit.

2. Position the supplied plastic water tray flat

on the floor under the drain hole.

3. Remove the drain knob and the rubber plug

from the drain hole. The condensed water will

drain out automatically.

4. When the water tray is almost full, replace

the rubber plug into the drain hole to stop the

water. Empty the water tray.

5. Repeat steps 2, 3 and 4 until all the

condensed water is emptied.

6. One all the condensed water has been

removed, replace the rubber plug into the

drain hole firmly. The 'Tank Full' indicator

should be off now.

7. Replace the drain knob.

By water tube (continuous drainage)

1. Remove the drain knob and rubber plug

and keep them for future use.

2. Connect the supplied water tube to the

water hole. The condensed water will drain

out automatically.

3. If you want to extend the water tube, you

can connect it with another tube (outside

diameter 18 mm).

Rubber plug Drain knob Water tray

Drainage

Always unplug the unit from the mains before beginning the cleaning.

Cleaning the housing.

• Use a soft, damp cloth to wipe the body clean.

• Never use aggressive chemicals, petrol, detergents, chemically treated cloths or

other cleaning solutions. These could possibly damage the cabinet.

Maintenance

non washable deodorising

carbon filter

washable foam antibacterial

filter

filter frame

Cleaning the filter.

• Lift out the filter frame and remove

the black carbon filter - this should

NOT be washed. The black foam

antibacterial filter may be washed

along with the frame.

• Use a vacuum cleaner or tap the filter

lightly to remove loose dust and dirt

from the filters and then rinse them

thoroughly under running water (no

hotter than 40 °C).

• Dry thoroughly before replacing the

carbon and antibacterial filters and

then replace the frame into the unit.

Notice! Never operate the unit without the filters.

End of season storage.

• Unplug the unit.

• Drain the condensed water

completely (see page 8).

• Clean or change the filter.

• Turn the unit to fan mode for a

couple of hours in a warm room

so that the inside can dry out

completely.

• It is recommended that the unit be

put back in its original carton for

storage.

• Do not stack heavy objects on top of

the unit.

When the unit is not in use, please tidy

the power cord away as shown.

Never try to repair or dismantle the air conditioner yourself. Incompetent repairs result in loss of warranty and can endanger the user.

The unit does not function Connect to a functioning outlet and

switch on

Water tank indicator is on Empty water tank

Room temperature outside operating

temperature range

The unit does not seem to perform In direct sunlight Close curtains

Windows or doors open, many people or

heat source in room

Dirty filter Clean or replace filter

Air inlet or air outlet blocked Remove blockage

Room temperature lower than selected value Change temperature selection

The unit is noisy Unit stands uneven Place on even surface (less vibrations)

The compressor does not work Overheat protection probably activated Wait until room temperature lowers

Trouble shooting

Table of contents

Popular Air Conditioner manuals by other brands

Spheros

Spheros CC 355 instructions

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE owner's manual

Panasonic

Panasonic CS-E12HKEW operating instructions

nedis

nedis ACMB1WT7 quick start guide

Samsung

Samsung AR KV Series User & installation manual

Daikin

Daikin FCFV50A Operation manual

Fujitsu

Fujitsu Inverter ASBA30JFC operating manual

Toshiba

Toshiba RAS-M10SMUV-E installation manual

Daikin

Daikin FXLQ20MAVE Operation manual

Hitachi

Hitachi RAS-E24CAK instruction manual

CIAT

CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance

Bestron

Bestron AAC6000 instruction manual

Hisense

Hisense 7K Use and Installation Instructions

Frigidaire

Frigidaire FFRE0533S1E0 Use & care guide

Samsung

Samsung AS09HM3N user manual

Frigidaire

Frigidaire CRA073PU11 use & care

Soleus Air

Soleus Air GB-PAC-08E4 operating instructions

McQuay

McQuay MCK020A Technical manual