ADA INSTRUMENTS Cosmo 70 User manual

Operating manual

Laser distance meter

Model: COSMO 70

COSMO 70

Table of contents

1. Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

2. Start up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3. Menu functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

4. Measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

5. Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

6. Message codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

7. Techical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

8. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

9. Exceptions from responsibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Appendix 1 - “Certificate of acceptance and sale”

Appendix 2 - “Warranty card”

COSMO 70 3

Congratulations on the purchase of laser distance meter ADA COSMO 70!

Permitted use

· Measuring distances

· Computing functions, e.g. areas, volumes, subtractions, Pythagorean calculation

· Storing measurements

The safety regulations and instructions along with the operating manual should be read carefully

before initial operation.The person responsible for the instrument must ensure that equipment is

used in accordance with the instructions. This person is also accountable for the deployment of

personnel and for their training and for the safety of the equipment when in use.

COSMO 70

SAFETY INSTRUCTION

Prohibited use

Please follow up instructions given in operating manual.

Do not use instrument in explosive environment (filling station, gas equipment, chemical production and so on).

Do not remove warning labels or safety instructions.

Do not open instrument housing, do not change it’s construction or modification.

Do not stare at beam. Laser beam can lead to eye injury (even from greater distances).

Do not aim laser beam at persons or animals.

Opening of the equipment by using tools (screwdrivers, etc.), as far as not specifically permitted for certain cases.

Inadequate safety precautions at the surveying site (e.g. when measuring on the roads, construction sites and so on).

Use the instrument in the places where it could be dangerous: on the air transport, near manufacturers,

production facilities, in the places where the work of laser distance meter can lead to the harmful effects on

people or animals.

COSMO 70 5

START UP

Keypad

1. ON / Measure

2. Area / Volume / Pythagorean measure

3. Subtraction / Timer

4. Clear / OFF

5. Addition / Units

6. Reference

COSMO 70

Display

1. Laser ON

2. Reference (front/rear)

3. Area / volume/ Pythagorean

4. Main line

5. Line 2

6. Line 1

7. Units

8. Timer On

9. Battery display

10. Error

9 8

COSMO 70 7

Inserting / Replacing Batteries

Remove the end piece on 180º. Remove the battery cover, insert the battery correctly. Pay attention to

correct polarity.

Close the battery compartment.

Replace the battery when symbol constantly blinks in the display.

Batteries should be removed in case of danger of corrosion, if the device will not be used for a long time.

MENU FUNCTIONS

Swtich on and off

Press the button (1) to switch on the instrument and laser.

Press and hold key for about 2 seconds to start continuous measuring.

The device also switches off automatically after 3 minutes of inactivity i.e. no key is pressed within that

interval. To switch off the instrument press and hold button (4) for about 2 sec.

COSMO 70

Reference Setting

Default reference setting is from the rear of the device.

Press the button (6) to set the reference: the front or the rear.

When the end-piece is folded out fully, the reference rear is set.

You will see the reference symbol on the display.

Selecting Units

Press and hold the button (5) for 2 sec. until the desired unit is displayed.

Clear-Key

Cancel the last action. Press button (4).

COSMO 70 9

MEASUREMENTS

Single distance measurement

Press button (1) to activate the laser. When in continuous laser mode, press this button to trigger the distance measure-

ment directly. The instrument will give acoustical signal.

The result is displayed immediately.

Continuous Measurement

Press and hold the button (1) for about 2 seconds to start continuous measuring.

Minimum/ Maximum measurement

This function allows the user to measure the minimum or maximum distance from a fixed measuring point. It is com-

monly used to measure room diagonals (maximum values) or horizontal distances (minimum values).

Press and hold down the button (1), until you will hear acoustical signal. Then slowly sweep the laser back and forth

COSMO 70

and up and down over the desired target point (e.g. into the corner of a room).

Press (1) to stop continuous measurement. The values for maximum and minimum distances are shown on

the display as well as the last measured value in the main line.

FUNCTIONS

Distance measuring

Press button (5): next measurement is added to the previous one. Press button (3): next measurement is substracted

from the previous one.

To complete this function press button (1). Repeat this function to measure distances. The result is des-

played in the main display area. Previous measured value is displayed in the first line, last measured value

is displayed in the second line. To finish working in this mode press button (4).

Table of contents

Languages:

Other ADA INSTRUMENTS Measuring Instrument manuals

ADA INSTRUMENTS

ADA INSTRUMENTS Vertical User manual

ADA INSTRUMENTS

ADA INSTRUMENTS Robot Mini User manual

ADA INSTRUMENTS

ADA INSTRUMENTS WHEEL 100M User manual

ADA INSTRUMENTS

ADA INSTRUMENTS CUBE 360 User manual

ADA INSTRUMENTS

ADA INSTRUMENTS ProDigit MICRO User manual

ADA INSTRUMENTS

ADA INSTRUMENTS COSMO MINI User manual

ADA INSTRUMENTS

ADA INSTRUMENTS PROF X2 User manual

ADA INSTRUMENTS

ADA INSTRUMENTS ProDigit MICRO User manual

ADA INSTRUMENTS

ADA INSTRUMENTS PRODIGIT MARKER User manual

ADA INSTRUMENTS

ADA INSTRUMENTS DigiTeo-2 User manual

ADA INSTRUMENTS

ADA INSTRUMENTS ProDigit MICRO User manual

ADA INSTRUMENTS

ADA INSTRUMENTS LASERMARKER 70 User manual

ADA INSTRUMENTS

ADA INSTRUMENTS ROBOT-40 User manual

ADA INSTRUMENTS

ADA INSTRUMENTS ProDigit MICRO User manual

ADA INSTRUMENTS

ADA INSTRUMENTS ZHT 100 User manual

ADA INSTRUMENTS

ADA INSTRUMENTS ZHT 125 Electronic User manual

ADA INSTRUMENTS

ADA INSTRUMENTS PROF X15 User manual

ADA INSTRUMENTS

ADA INSTRUMENTS ROTARY 500 HV SERVO User manual

ADA INSTRUMENTS

ADA INSTRUMENTS 3D Liner 2V Green User manual

ADA INSTRUMENTS

ADA INSTRUMENTS PaintMeter 1500 User manual

ADA INSTRUMENTS

ADA INSTRUMENTS ProDigit 60 User manual

ADA INSTRUMENTS

ADA INSTRUMENTS ZSM 330 User manual

ADA INSTRUMENTS

ADA INSTRUMENTS WHEEL 50 DIGITAL User manual

ADA INSTRUMENTS

ADA INSTRUMENTS Ruber-X32 User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual