ABB TZIDC-110 User manual

P R OF I

BU S

PROCESS FIELD BUS

Operating Instructions

41/1877 EN

Electro-Pneumatic Positioner

TZIDC-110

for PROFIBUS PA

2 Electro-pneumatic positioner TZIDC-110 41/18-77 EN

ElectroPneumatic Positioner TZIDC110

for PROFIBUS PA

Operating Instructions

Document No.: 41/18-77 EN

Issued: 04.05

Manufacturer

ABB Automation Products GmbH

Schillerstr. 72

32425 Minden

Germany

Tel: +49 551 905-534

Fax: +49 551 905-555

[email protected]b.com

Note

More information, e.g. regarding configuration, operation and ordering details, is available

on CD.

Modifications reserved

This document is subject to copyright. It is intended to help the user operate the equipment safely

and efficiently. The content may not be copied or reproduced either in part or in full without the

prior consent of the copyright owner.

41/18-77 EN Electro-pneumatic positioner TZIDC-110 3

Table of contents

Important information....................................................................................................... 5

1 Safety summary............................................................................................................ 6

1.1 General safety instructions .....................................................................................6

1.2 Device-specific safety instructions.........................................................................7

1.2.1 General .......................................................................................................... 7

1.2.2 Pneumatic safety .......................................................................................... 7

1.2.3 Electrical safety .............................................................................................. 8

1.3 Explosion protection................................................................................................9

1.4 Correct use................................................................................................................9

1.5 Qualified personnel ..................................................................................................9

2 Manufacturer's information.................................................................................... 10

2.1 Delivery....................................................................................................................10

2.2 CE compliance information ...................................................................................10

3 Installing and commissioning............................................................................... 11

3.1 Mechanical mounting.............................................................................................11

3.1.1 General......................................................................................................... 11

3.1.2 Operating conditions at the installation site .................................................. 12

3.1.3 Mounting the positioner to linear actuators................................................... 12

3.1.4 Mounting the positioner to rotary actuators .................................................. 17

3.2 Pneumatic connection ...........................................................................................20

3.2.1 Safety instructions ...................................................................................... 20

3.2.2 Making the pneumatic connections .............................................................. 20

3.2.3 Mounting the splash guard cap .................................................................... 21

4 Electro-pneumatic positioner TZIDC-110 41/18-77 EN

3.3 Electrical connection..............................................................................................22

3.3.1 Safety instructions ........................................................................................ 22

3.3.2 General installation instructions ................................................................... 22

3.3.3 Overview....................................................................................................... 23

3.4 Commissioning.......................................................................................................25

3.4.1 Procedure ..................................................................................................... 25

3.4.2 Setting the bus address................................................................................ 27

3.4.3 Requesting information................................................................................. 28

3.4.4 Local operation (bus device)......................................................................... 28

3.4.5 Parameter setting example .......................................................................... 29

3.5 Functional test / maintenance ...............................................................................30

3.5.1 Functional test of the shutdown module ....................................................... 31

4 Technical data ............................................................................................................. 32

4.1 Basic model.............................................................................................................32

4.2 Options ....................................................................................................................36

5 Certificates.................................................................................................................... 38

Appendix A: Configuration overview........................................................................ 56

41/18-77 EN Electro-pneumatic positioner TZIDC-110 5

Important information

Symbols

In order that you can make the best use of this document and to ensure safety during commis-

sioning, operation and maintenance of the equipment, please note the following explanation of

the symbols used:

As well as the instructions in this document, you must also follow the generally applicable acci-

dent prevention and safety regulations.

If the information in this document is insufficient in any situation, please contact our service de-

partment, who will be happy to help you.

Please read this document carefully before installation and commissioning.

Symbol Signal Word Definitions

DANGER DANGER indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

(High level of risk.)

WARNING WARNING indicates a potentially hazardous situation

which, if not avoided, could result in death or serious

injury.

(Medium level of risk.)

CAUTION CAUTION indicates a potentially hazardous situation

which, if not avoided, could result in minor or moderate

injury.

(Low level of risk.)

NOTICE NOTICE indicates a potentially harmful situation which, if

not avoided, may result in damage of the product itself or

of adjacent objects.

(Damage to property)

IMPORTANT IMPORTANT indicates useful hints or other special

information which, if not observed, could lead to a decline

in operating convenience or affect the functionality.

(Does not indicate a dangerous or harmful situation.)

6 Electro-pneumatic positioner TZIDC-110 41/18-77 EN

1 Safety summary

1.1 General safety instructions

This chapter provides important instructions for your safety. Thoroughly read and follow

these instructions.

Proper and safe operation of the TZIDC-110 positioner requires:

• proper transportation and storage

• mounting, electrical and pneumatic installation and commissioning by qualified per-

sonnel (see chapter 1.5, page 9)

• correct operation according to the instructions in this manual

• correct use (see chapter 1.4, page 9)

• careful maintenance

The regulations, standards and directives referred to in this manual are applicable in Ger-

many. When using the TZIDC-110 positioner outside the German jurisdiction, the rele-

vant regulations, standards and directives applicable in the country where the device is

used must be observed.

The TZIDC-110 positioner has been designed and tested in accordance with

DIN VDE 0411 Part 1 / EN 61 010 Part 1

“Safety Requirements for Electronic Measuring Apparatus”

(based on IEC Publication 348) and has been delivered in a safe condition.

In order to retain the device in a safe condition and ensure safe operation, attentively

read and follow the instructions given in the sections marked with the respective sym-

bols. (See “Important information” on page 5.) Otherwise, persons can be endangered or

the device itself or other devices or equipment may be damaged or fail.

The device must be shut down and secured reliably against unintentional restart if it must

be assumed that safe operation is no longer ensured. Possible reasons for this assump-

tion can be:

• visible damage of the device

• failure of the electrical function

• exposure to a storage temperature of more than 85 °C for a longer time period

• exposure to considerable strain or wear during transport

Only the manufacturer is authorized to repair the device.

41/18-77 EN Electro-pneumatic positioner TZIDC-110 7

1.2 Device-specific safety instructions

1.2.1 General

1.2.2 Pneumatic safety

WARNING

• Any user-made changes or manipulations of the device are prohibited!

Only the manufacturer or an expert for explosion protection are authori-

zed to modify the device.

• Before re-using a TZIDC-110 positioner that has already been used in

another installation place always reset the device to the factory setting.

Never start the autoadjustment function before having restored the fac-

tory setting! Otherwise, hazardous situations may occur due to impro-

per settings.

• Do not use the internal communication interface (X5) on the mother-

board when the TZIDC-110 positioner is installed and used in the

hazardous area.

• The (optional) safety shutdown module must be subject to a functional

test every two years at the latest. Follow the instructions in chapter

3.5.1.

WARNING

• Observe the accident prevention rules of the Employers Liability Insu-

rance Association.

• Observe the safety instructions for the pneumatic actuator used. The

actuator's high actuating power may cause injuries !

NOTICE

• Take suitable precautions to ensure that even in case of malfunctions

the positioner’s max. admissible operating pressure of 6 bar (90 psi) is

not exceeded. Otherwise, the positioner and/or the actuator may be

damaged.

• The positioner must be supplied with instrument air exempt from oil,

water and dust according to DIN/ISO 8573-1, Class 3

- Purity: max. particle size 5 µm, max. particle density 5 mg/m3

- Oil content: max. concentration 1 mg/m3

- Pressure dew point: maximum value 10 K below operating temp. 3

Before connecting the air pipes blow them out to remove dust, splinters

and other particles.

8 Electro-pneumatic positioner TZIDC-110 41/18-77 EN

1.2.3 Electrical safety

WARNING

• Observe the common VDE safety regulations and the accident preven-

tion rules of the Employers Liability Insurance Association.

• Observe the common standards and safety regulations for the installa-

tion and operation of electrical systems.

• When connecting the device, observe all electrical specifications in

these operating instructions or in the data sheet.

• For the electrical installation of explosion-protected devices, observe all

standards, regulations and directives governing explosion protection

and applicable for the construction and use of explosion-protected sys-

tems, especially the DIN/VDE directives, the directives for explosion

protection (VDE 0165 or EN 60079), and the special requirements and

specifications for your devices (see the following chapter "Explosion

protection" and chapter "Certificates" starting on page 38).

• Excusively power devices with explosion protection via an electrically

isolated circuit with safe extra-low voltage (SELV) in accordance with

EN 60 950.

NOTICE

Power supply

• The basic device is bus-powered via the Fieldbus connected to the bus

terminals +(11) and -(12). The option modules have to be supplied

separately.

• When connecting a power source for test purposes without establishing

a bus communication (e.g. when executing the Autoadjust function), a

supply voltage between 9.0 V DC and a maximum of 32 V DC can be

applied.

NOTICE

Electromagnetic interference

• Do not run bus/signal lines close to power lines. Power lines produce

interference in their near vicinity which may affect the electrical capabi-

lities of the bus/signal lines.

• In order to ensure electromagnetic compatibility (EMC), always use

shielded cables conforming to the standards for the bus lines. When

running the device with the option modules (proximity switches, mic-

roswitches, shutdown module) use shielded cables for these modules

as well. All cable shields must be kept as short as possible and have to

be connected to protective ground on both sides (use the grounding

screw in the TZIDC-110 connection compartment on the device side).

• Keep the case closed. When the case is open, the positioning action

may be affected through electromagnetic interference. This may result

in a permanent positioning error, especially when the Autoadjust func-

tion is performed with the case open.

41/18-77 EN Electro-pneumatic positioner TZIDC-110 9

1.3 Explosion protection

One of the type plates seen below is attached to the positioner to the left of the main type

plate, depending on the positioner’s explosion protection. It indicates the degree of explo-

sion protection and the certificate valid for your positioner. For details please refer to

chapter "Certificates" starting on page 38.

1.4 Correct use

The TZIDC-110 positioner is an electro-pneumatic positioner for pneumatic final control

elements. It is designed for being attached to linear and rotary actuators following the

instructions in this manual. The positioner may be used only for the applications listed in

these operating instructions or in the data sheet 18-0.23 EN. Any other use is considered

as incorrect.

The signal current circuit and the input and output circuitry must meet the explosion pro-

tection requirements stipulated in the certificates (see chapter "Certificates" starting on

page 38).

The maximum permissible ambient temperature range of -40 °C to +85 °C (when using

proximity switches of type SJ2-S1N (NO): -25 °C to + 85 °C) must not be exceeded.

1.5 Qualified personnel

Only those persons familiar with the installation, commissioning, operation and mainte-

nance of the TZIDC-110 positioner or similar instruments who have the required qualifi-

cation and have read and understood the operating instructions are authorized to work

on the TZIDC-110 positioner. These persons must be sufficiently trained and experi-

enced and know the relevant standards and regulations to be able to judge their assig-

ned tasks and recognize potential hazards. Only persons who are qualified or have been

trained adequately and who have the required certificates are authorized to work on

explosion-protected devices.

WARNING

Always observe the specifications and special requirements for your

positioner stipulated in the applicable certificate.

Fig. 1 Type plates indicating the degree of explosion protection

10 Electro-pneumatic positioner TZIDC-110 41/18-77 EN

2 Manufacturer's information

2.1 Delivery

When receiving the delivery please immediately check items and scope for intactness

and completeness. The scope of delivery is stated in the shipping documents. If ordered,

the accessories (e.g. mounting material, pressure gauge block, filter regulator) are added

to the delivery as individual items. Check items and scope of the delivery by means of

the catalog numbers to see if types and quantities are in accordance with your order. If

the positioner is delivered already mounted to the actuator, the positioner, accessories

and actuator or final control element are considered as a common delivery item. A list of

catalog numbers and details of the different versions and accessories can be found in

data sheet 18-0.23 EN.

2.2 CE compliance information

We declare that we are the manufacturer of the TZIDC-110 positioner and that the pro-

duct conforms with the EMC Directive 89/336/CEE as of May 1989 and meets the

requirements of the following standards:

• EN 55022:1998 “Information technology equipment, Radio disturbance

characteristics, Limits and methods of measurement”

• EN 61000-6-2:8/2002 ”Electromagnetic compatibility (EMC)

Part 6-2: Generic standards - Immunity for industrial environments

• EN 61000-6-3:3/2000 “Electromagnetic compatibility (EMC)

Part 6-3: Generic standards - Emission standard for residential,

commercial and light-industrial environments

The TZIDC-110 positioner complies with the EC directive for CE conformity certification.

Other manuals for TZIDC-110

Table of contents

Other ABB Controllers manuals

ABB

ABB ACS 501 Installation and operation manual

ABB

ABB COMMANDER 351 User manual

ABB

ABB Ability BECL/D.200.16 User manual

ABB

ABB ControlMaster CM50 User manual

ABB

ABB NextMove e100 User manual

ABB

ABB PSE18 User manual

ABB

ABB RTC-F-1.PB User manual

ABB

ABB ControlMaster CM30 User manual

ABB

ABB DSQC 667 Instructions for use

ABB

ABB ACH550-UH HVAC User manual

ABB

ABB COMMANDER 310 User manual

ABB

ABB ACS 6000 Installation and user guide

ABB

ABB ACQ80-04 Series User manual

ABB

ABB ACS55-01E-01A4-2 User manual

ABB

ABB AC 800F Installation and operation manual

ABB

ABB IRC5 Compact User manual

ABB

ABB ACH550 series User manual

ABB

ABB COM600 series User manual

ABB

ABB SA-M 16.2.2 Series User manual

ABB

ABB ACS880-17 User manual

ABB

ABB Totalflow mflo Series User guide

ABB

ABB RHDE250 User manual

ABB

ABB Galaxy Millennium J2011002 User manual

ABB

ABB REC650 ANSI User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

3M MicroTouch EX113 reference guide