ABB PST30 User manual

1SFC132004M0201

Quickstart PST30...PSTB1050

This document is a short guide to how to connect, do the

configuration and start the softstarter in the easiest way.

Warning!

Mounting, electrical connection and settings of the

softstarter shall be made in accordance with existing laws

and regulations and be performed by authorised personnel.

Do not change any parameters in the Service Settings

menu.

Connection

1. Mount the softstarter according to Chapter 4 “Mounting“,

see manual 1SFC132003M0201.

2. Be aware of the ambient temperature.

Derating is required above 40 °C (104 °F).

3. Connect the main circuit: terminals 1L1 - 3L2 - 5L3 to the

line side and terminals 2T1 - 4T2 - 6T3 to the motor side.

4. Connect the supply voltage: terminal 1 and 2

(100-250V 50/60Hz).

5. Connect the functional ground: terminal 3.

The wire shall be as short as possible, and be connected to

the mounting plate.The mounting plate should also be

earthed.

6. Connect the start/stop circuits: terminal 4, 5, 8, 9 and 10

according to the diagram. 24V DC only.

7. Check that the main and supply voltage corresponds to

the softstarter ratings.

8. Switch on the supply voltage.

9. The green "Power on" LED is on and the LCD shall

appear as in figure 3.

Power on ProtectionFault

1SFC132029F0001

U= 0% I=0.0A

igure 1:

Status indication LEDs

LCD display

Selection keys for selecting, changing

and storing parameters

Navigation keys for navigating in the

menus

Arrows shown in the display indicates

that the value/menu is possible to

change or scroll

KM1

1L1 3L2 5L3

2T1 4T2 6T3

6789

12 13 14 15 16 17 18 19 20

UVW

12 3 4 5

45 10

1SFC132030F0001

10 11

igure 2: Standard connection PST

StartStart

Start

Stop

Power on ProtectionFault

igure 3: Top level

U= 0% I=0.0A

21SFC132004M0201

Quickstart PST30...PSTB1050

ABB Automation Technologies AB, Cewe-Control, SE-721 61 Västerås, Sweden, Telephone +46 21 32 07 00, Telefax +46 21 12 60 01

Manual 1SFC132003M0201 January 2005 ABB Automation Technologies AB, Cewe-Control

Configuration

1. Enter the Application Setting by pressing left selection key

twice. Press Select using the left selection key. Figure 4.

2. Select the appropriate type of load using navigation keys.

Figure 5.

3. Press Store Set and Next to continue or Back to previous

parameter using the selection keys. Figure 6.

4. Set the Setting Ie using the navigation keys.

In Line connected = rated motor current

nside Delta connected = 58% ( ) of the rated motor

Icurrent. Figure 7.

5. Press Store and Next to continue or Back to previous

parameter using the selection keys. Figure 8.

6. Set the required overload class using the navigation keys.

Figure 9.

7. Press Store and Next to continue or Back to previous

parameter using the selection keys. Figure 10.

8. If an external by-pass contactor is used set Ext ByPass to

Yes using the navigation keys. (PST30...300 only).

Figure 11.

9. Press Store and Next to continue or Back to return to pre-

vious parameter using the selection keys. Figure 12.

10.Select Yes if ready or Tune Set if ramp times, initial volt-

age, current limit etc. needs to be adjusted using selection

keys. Figure 13.

11.To change presentation language, see manual

1SFC132003M0201.

Start of the motor

1. Switch on the main voltage.

2. Give start command to the softstarter.

(To start the softstarter from the keypad, enter the LOCAL

CONTROL menu, select Start/Stop and press Start. The

motor must be stopped before leaving this menu.)

Application Setting

Select Back

igure 4: Application setting menu

Centrifugal Pump

Store Set Back

igure 5: Centrifugal pump

Centrifugal Pump

Next Back

igure 6: Centrifugal pump stored 13()⁄

Setting Ie 99.0A

Store

igure 7: Setting Ie

Setting Ie 99.0A

Next Back

igure 8: Setting Ie stored

OL Class 10

Store

igure 9: OL Class

OL Class 10

Next Back

igure 10:OL class stored

Ext ByPass No

Store

igure 11: External Bypass

Ext ByPass No

Next Back

igure 12:External Bypass stored

Ready?

Yes Tune Set

igure 13:Ready / Tune Set

Other manuals for PST30

This manual suits for next models

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

3M MicroTouch EX113 reference guide