ZKTeco AL10B User manual
Installation Instruction
AL10B&AL20B
Version: 1.1
InstallationDiagram
Single Latch(Illustrated by the case of AL20B)
1
B
A
C
D
E
F
G
H
C
I
J
K
L
M
A
G
FK
B D
CI
2
Packing List
NH(1pcs) E(4pcs) J(2pcs) L(1pcs)
M(2pcs)
Door thickness
PM4*20 PM4*30 PM4*40
KM4*25 KM4*35 KM4*45
KM3*5
7.5*7.5*56 7.5*7.5*64 7.5*7.5*72
30-38mm 39-46mm 47-54mm
3
Note: To ensure proper functioning of the device only use the mounting hardware package for your door
thickness.
Note: Please refer to the above picture to adjust the direction of strike plate F and latch D.
1. Check the door thickness and prepare the corresponding mounting
hardware package.
2. Check door opening direction.
F
F
F
F
D D
DD
30~38 56 20 10 25
39~46 64 30 10 30
47~54 72 40 10 40
H Spindle Length
(mm)
J Screw Length
(mm)
M Screw Length
(mm)
L Screw Length
(mm)
Door Thickness
(mm)
4
Door Preparation
Left inward Right inward
Left outward Right outward Standpoint
1) Align the template along the vertical center line of the
latch(D) at the desired handle height, and tape it to the door.
2) Mark the holes first, and then start drilling.
1.Drill holes on the door. 2.Install the latch (D).
E
centerlineofthe
handle
h
desired handle
height
Installation
5
Note Installing the mortise(D) on the door :
by inserting screws(E).
30~60mm
60mm
3.Install outdoor unit (B) with gasket (C) and spindle (H) on the door.
6
H
B
C
3.3
Attach
outdoor unit
(B) to door
by putting
it through
door
holes.
3.2
Insert
spindle (H)
into
the clutch.
3.1 Put gasket (C) on
outdoor
unit
(B).
Clutch c orrect p osition: T he triangle
must b e v ertically c entered.
Incorrect position
4.Install mounting plate (I) with gasket (C) on the door.
J
5.Install indoor unit (K).
ML
7
IC
B
C
J
L
M
4.1 P ut m ounting p late (I) o n g asket(C). 4.2 I nserting s crews(J) t o s ecure t he o ut-
door u nit.
5.3 Secure indoor unit (K) to outdoor unit
(B) by inserting screws (M) and screw (L).
5.1 Connect the indoor unit (K)
cable to the o utdoor unit (B). 5.2 Push the cable into the hole.
6.Insert batteries.
K
EG
F
7.Mark and drill holes for the strike.
8. Test the lock by rotating the back handle and using the mechanical
Key (A).
Note:
1) When the door is locked and the clutch is idle, the front handle can be
turned, but the door will remain locked.
2) When you are inside the door, turn the handle upward to lock the deadbolt
for more security. When you go out, verify your fingerprint first, and then turn
the handle up to lock the door for the safety of your property.
8
58(mm)
(2-36/127")
(215/254")
(70/127")
(1-48/127")
2(mm)
(10/127")
14(mm)
(70/127")
35(mm)
14(mm)
(1-18/127")
29(mm)
21.5(mm)
Change latch (D) direction.
Fix the latch trim panel by using screws.
Remove screws from the latch trim panel with a
screwdriver and rotate the latch bolt at 180°.
9
A
How To Use Mechanical Key And Change Handle Direction?
How To Use Key & Changing Handle Direction?
Hexagon Screw
N
Hexagon Screw
N
2. Pull handle away
from l ock.
1. Use wrench (N) to re-
move screw.
3. Insert mechanical key into hole
to open the door.
2. Pull handle away
from l ock.
3. Change handle direction
and replace.
4. Replace the screw
on the opposite side.
1. Use wrench (N) to re-
move screw.
Other manuals for AL10B
2
This manual suits for next models
1
Table of contents
Other ZKTeco Door Lock manuals
ZKTeco
ZKTeco GL300 User manual
ZKTeco
ZKTeco L9000 User manual
ZKTeco
ZKTeco LH6500 User manual
ZKTeco
ZKTeco AL30Z User manual
ZKTeco
ZKTeco DL30B User manual
ZKTeco
ZKTeco LH7000 User manual
ZKTeco
ZKTeco ML10-ID User manual
ZKTeco
ZKTeco LH6000 User manual
ZKTeco
ZKTeco ZL400 User manual
ZKTeco
ZKTeco ZL600 User manual
ZKTeco
ZKTeco ML200 Series User manual
ZKTeco
ZKTeco L5000 User manual
ZKTeco
ZKTeco ZL500 User manual
ZKTeco
ZKTeco HBL100 User manual
ZKTeco
ZKTeco L4000 User manual
ZKTeco
ZKTeco PL10 Series User manual
ZKTeco
ZKTeco DL30 Series User manual
ZKTeco
ZKTeco ML10 Series User manual
ZKTeco
ZKTeco TL100 User manual
ZKTeco
ZKTeco HBL400 User manual
