TRU-BOLT 08102017 User manual
USER MANUAL - ELECTRONIC DEADBOLT WITH REMOTE
08102017
Index
OPERATION INSTRUCTIONS
Exterior Assembly Overview.......................................................................Page 9
Locking and Unlocking / Changing Programming Code /
Adding User Codes......................................................................................Page 10
Deleting User Codes / Automatic Lock Function /
Temporarily Disable Auto Lock...................................................................Page 11
Remote Control Set-Up and Operation......................................................Page 12
Vacation Mode / Sound On and Off / Secure Lock-out Period................Page 13
Restore Factory Settings / Low Battery Warning /
Consumer Friendly Message Guide...........................................................Page 14
Installation Trouble Shooting...............................................................Page 15
Consumer Assistance.................................................................................Page 16
Template.......................................................................................................Page 17-18
Programming Record..................................................................................Page 19-20
Limited Warranty.................................................................................Page 21
INSTALLATION INSTRUCTIONS
Package Contents / Tools Required......................................................... Page 1
Prepare Door and Jamb..............................................................................Page 2
Adjusting Deadbolt Latch Set.....................................................................Page 3
Installing Deadbolt Latch Set.....................................................................Page 4
Preparing Interior Assembly.......................................................................Page 5
Installing Exterior Assembly.......................................................................Page 6
Installing Interior Assembly........................................................................Page 7-8
For troubleshooting tips and “how to videos” visit www.truboltlocks.info
Page 1
B.A.
C. D.
INSTALLATION INSTRUCTIONS
Package Contents
Tools Required
Tools Required for Installation
on Pre-drilled Doors:
• Phillips Head Screwdriver
NOTE: DO NOT USE a drill.
Tools Required for Installation
on Doors That Require Drilling:
• Drill
• Tape Measure
• Pencil
• 2-1/8” (54mm) Drill Hole Saw
• 1” (25mm) Drill Bit
• 1/16” (2mm) Drill Bit
• Chisel
• Hammer
• Phillips Head Screwdriver
Deadbolt Strike Plate
Deadbolt Latch Set (Adjustable)
2-3/8” (60mm) to 2-3/4” (70mm)
Interior Assembly Mounting Plate Exterior Assembly
Entry keys (2 ea.)
Wireless Remote (1 ea.)
5/16” (8mm) Screws - 2 ea. 7/8” (22mm) Screws - 2 ea.
3/4” (19mm) Screws - 5 ea. 1” (25mm) Screw - 1 ea.
Electronic lock requires (4) High Quality
AA Alkaline batteries. When all 4 batteries
are installed in the correct position, hear 2
beeps and the keypad will illuminate blue.
DO NOT TOUCH the keypad until the keypad
stops illuminating.
Batteries (not included)
Page 2
NOTE: For installation on doors with pre-drilled holes skip to page 4.
1. TEMPLATE
a. Cut out template printed on page 17 & 18 of this Manual
(Figure 1a).
b. Fold template and place on door 36” (915mm) from
the ground as marked (Figure 1b).
2. MARK THE DOOR FOR DRILLING
b. Mark center hole on door edge through guide on
template for 1” (25mm) latch bolt (Figure 2a).
a. Mark center hole on door face through guide on
template for 2-3/8” (60mm) or 2-3/4” (70mm)
backset (Figure 2b).
3. DRILL AND CHISEL DOOR
a. Drill 2-1/8” (54mm) hole through door face as marked
for lock set (Figure 3a).
b. Drill 1” (25mm) hole in center of door edge for
Deadbolt Latch Assembly (Figure 3b).
c. Insert Deadbolt Latch Assembly in hole keeping it
parallel to face of door. Mark outline and remove latch
(Figure 3c).
d. Chisel 1/8” (3mm) deep or until latch face is ush
with door edge (Figure 3d).
4. MARK AND DRILL DOOR JAMB
a. Mark center hole on edge of jamb even with the center of the Latch Bolt on door
edge. (Figure 4a).
b. Drill 1” (25mm) hole 1-3/16” (30mm) deep in door jamb on center mark (Figure 4b).
c. Outline outside edges of Strike Plate (Figure 4c).
d. Chisel 1/8” (3mm) deep for Strike Plate or until ush (Figure 4d).
e. Install Strike Plate using two 3/4” (19mm) screws provided (Figure 4e).
PREPARE DOOR AND JAMB
Figure 4a Figure 4b Figure 4e
Figure 4c Figure 4d
NOTE: For Drive in Latch, drill hole size indicated on template and
press until it is ush with door edge.
UP
Figure 1a
Figure 2a Figure 2b
Figure 3a
Figure 3c
Figure 1b
Figure 3b
Figure 3d
2-1/8” (54mm)
Page 3
ADJUSTING DEADBOLT LATCH SET
NOTE: Deadbolt Latch Set is shipped with the backset set at 2-3/8” (60mm)
Measure the backset (backset is distance between edge of the door and the center of Lock).
1. TO CONVERT FROM 2-3/8” (60mm) BACKSET TO 2-3/4” (70mm) BACKSET
a. Hold latch with numbers facing forward and thumb pressing on the bolt (Figure 1a).
b. Rotate the cylinder cover clockwise (Figure 1b).
c. Pull and twist the extension plate all the way out (Figure 1c).
d. Rotate the cylinder cover counter clockwise so that the marking aligns with
the 2-3/4” (70mm) position indicator (Figure 1d).
2. TO CONVERT FROM 2-3/4” (70mm) BACKSET TO 2-3/8” (60mm) BACKSET
a. Hold latch with numbers facing forward and thumb pressing on the bolt (Figure 2a).
b. Rotate the cylinder cover clockwise (Figure 2b).
c. Push and twist the extension plate all the way in (Figure 2c).
d. Rotate the cylinder cover counter clockwise so that the marking aligns with
the 2-3/8” (60mm) position indicator (Figure 2d).
Figure 1a Figure 1b Figure 1c
Figure 1d
Must lock in place.
Figure 2a Figure 2b Figure 2c
Figure 2d
NOTE: Do not extend Cylindrical Cover past 2-3/4” (70mm)
or it will break once extended
Page 4
3. INSTALLING THE DEADBOLT LATCH SET (need Phillips head screwdriver)
a. Insert Deadbolt Latch Set into door edge hole with the word
“UP” and the arrow on the extension plate facing UP. Cross
shaped spindle connector will be at the bottom of the Deadbolt
Latch Set (Figure 3a).
b. Make sure the face plate sits ush with the door. Do not force
the latch into the mortise ush. Chisel out excess material if
necessary for a ush t.
c. Using two 3/4” (19mm). screws provided, screw the latch into the
door with a hand held screwdriver. DO NOT OVER TIGHTEN.
4. IDENTIFYING YOUR DOOR HANDING
Stand outside the door.
a. If the hinges are on the left your door is Left Handed (Figure 4a and 4b).
b. If the hinges are on the right your door is Right Handed (Figure 4a and 4b).
INSTALLING DEADBOLT LATCH SET
Figure 4a
OUT SWING DOOR
Left Handed Door
Hinges are on the left side
Right Handed Door
Hinges are on the right side
IN SWING DOOR
Left Handed Door
Hinges are on the left side
Right Handed Door
Hinges are on the right side
Figure 4b
Figure 3a
Deadbolt Latch Extended Deadbolt Latch Retracted
NOTE: Deadbolt Latch must be retracted when installing
NOTE: You are standing outside the door
Page 5
PREPARING THE INTERIOR ASSEMBLY
6. SET THE ENTRY SWITCH FOR LEFT OR RIGHT HANDED DOOR
a. Gently move the switch to “L” for Left Handed Door (Figure 6a).
b. Gently move the Switch to “R” for Right Handed Door (Figure 6b).
7. SET THE INTERIOR KNOB POSITION FOR LEFT OR RIGHT HAND HINGED DOORS
a. The Interior Knob goes in the Horizontal position for Left Handed Doors (Figure 7a).
b. The Interior Knob goes in the Vertical position for Right Handed Doors (Figure 7b).
Entry Switch (Left or Right)
Figure 6a-b
NOTE: Make sure deadbolt Latch is retracted
5. UNPACK THE INTERIOR ASSEMBLY
a. Remove the battery cover by sliding the cover upward.
b. Locate the screw holding the Mounting Plate to the Interior Assembly. Remove the
screw to release the Mounting Plate from the Interior Assembly.
Right Handed Door
(Vertical)
Left Handed Door
(Horizontal)
Figure 7a Figure 7b
Page 6
9. SECURING THE EXTERIOR ASSEMBLY TO THE DOOR
a. From the side marked “This side against
door”, route the Control Wire through the
rectangular slot in the Mounting Plate (Figure 9a).
b. Place Mounting Plate against door with tailpiece passing
through the center hole in the three hole set (Figure 9b).
c. Secure the Mounting Plate to the Exterior Assembly using
two 7/8” (22mm) Screws(B) (Figure 9c).
d. Hand tighten with a Phillips Screwdriver leaving loosely connected (Figure 9d).
e. Check that the Rubber Gasket is properly aligned and correct as necessary
(Figure 8a).
f. Check vertical alignment of the lock (Figure 9f).
g. Tighten securely with a hand held Phillips Screwdriver. DO NOT OVER TIGHTEN
10. OPTIONAL INSTALLATION
a. Using a 1/16” (2mm) drill bit, drill a pilot hole in your door using the
Mounting Plate upper hole as a guide (Figure 10a).
b. Insert one 3/4” (19mm) screw(C) and tighten.
8. INSTALLING THE EXTERIOR ASSEMBLY
Work with the Door Open for easy access.
a. Unpack the Exterior Assembly. Use care to not scratch the green circuit board
during handling and installation.
b. Check that the Rubber Gasket is properly seated on the Exterior Assembly
(Figure 8a).
c. Insert the Exterior Assembly onto the door with the tailpiece going through the
Deadbolt Latch Set cross shaped spindle connector in the VERTICAL POSITION.
Route the Control Wire through the door under the Deadbolt Latch Set (Figure 8c).
INSTALLING EXTERIOR ASSEMBLY
Right handed door view
Rubber
Gasket
Control
Wire
Mounting Plate
3/4” (19mm) screw
(Optional installation)
7/8” (22mm) screws
Control Wire
C
B
Tailpiece
(Vertical)
Latch
Hole
Figure 8a Figure 8c
Figure 10a
Figure 9a-f
NOTE: Lock and unlock using the key to see if
the Deadbolt Latch is opening and closing easily.
NOTE: Tailpiece must be
positioned vertically
Page 7
INSTALLING INTERIOR ASSEMBLY
11. ATTACH THE CONTROL WIRE TO THE INTERIOR ASSEMBLY
a. Use care to attach the Control Wire male plug to the Interior Assembly female
socket connector.
b. Carefully insert the male plug, smooth side up, into the female socket on the
interior assembly. DO NOT FORCE! (Figure 11a).
12. ATTACH THE INTERIOR ASSEMBLY TO DOOR
a. IMPORTANT: Make sure the knob is in the vertical position for right hand door and
horizontal position for left hand door.
b. Make sure the tailpiece (Figure 12a) is in the vertical position.
c. Position the Interior Assembly over the vertically positioned tailpiece and carefully
push the Interior Assembly against the door (Figure 12a).
d. Using two 5/16” (8mm) screws(A) and one 1” (25mm) screw(D), attach the
Interior Assembly to the Mounting Plate. DO NOT OVER TIGHTEN SCREWS
Vertical Tailpiece
NOTE: Lock and unlock using Interior Knob to see if the
latch is opening and closing easily.
Figure 12a
Match color
Figure 11a
5/16” (8mm) screws
1” (25mm) screw
A
D
Page 8
13. Installing Batteries
a. Slide battery cover up and remove.
b. Insert 4 AA high quality Alkaline batteries into the Battery Compartment in the
direction noted +/- on the Compartment. The Lock will beep 2 times, the keypad
will illuminate blue, and the Tru-Bolt button will ash green twice to signify that
it has received power (Figure 13a).
c. Replace battery cover and slide down on to the Interior Assembly to cover the
batteries (Figure 13b).
14. Testing Lock
a. Always test with the Door Open and in unlocked position.
b. Test the Lock using the Interior Knob. The bolt should move smoothly in and out.
c. Test the Lock using the Keypad. To lock press and then press “1234”
to unlock.
INSTALLING INTERIOR ASSEMBLY (CONT.)
Battery
Cover
4 AA
Batteries
NOTE: Do not touch the Keypad until the blue light turns off.
Do not use rechargeable batteries or non-alkaline batteries.
Figure 13a-b
INSTALLATION OVERVIEW
Strike Plate
3/4” (19mm) screws(C)
Mounting Plate
Interior Assembly
Optional
3/4”(19mm) Screw(C)
7/8”(22mm) screws(B)
Latch
Exterior Assembly
Control Wire
Rubber Gasket
Key
Remote
Battery Cover
5/16”(8mm)
screws(A)
1”(25mm)
Screw(D)
This manual suits for next models
1
Table of contents
Other TRU-BOLT Door Lock manuals
Popular Door Lock manuals by other brands
JAKO
JAKO JKBTNX4 installation guide
Dorma
Dorma MUNDUS PREMIUM GK 50 Mounting instruction
SCOOP
SCOOP Pullbloc 4.1 FS Panik Assembly instruction
Yale
Yale MORTISE 8800 SERIES installation instructions
Siegenia
Siegenia KFV AS3500 Assembly instructions
Saflok
Saflok Quantum ädesē RFID installation instructions