ZKTeco LH7000 User manual

Table of contents

Popular Door Lock manuals by other brands

Assa Abloy

Assa Abloy effeff 827A-IP Mounting instructions

We.lock

We.lock SECBNEBL51 instructions

Iseo

Iseo MA1A installation guide

ID Lock

ID Lock 150 user manual

Lockly

Lockly ACCESS TOUCH PRO user manual

iLoq

iLoq G50S user guide

SDC

SDC Z7835 installation instructions

ilco

ilco 452 Installation

Samsung

Samsung shs-h705 user guide

TRU-BOLT

TRU-BOLT 08102017 user manual

CDVI

CDVI 500-LADJ quick start guide

Igloohome

Igloohome Deadbolt 2S Metal Grey Installer/user guide

eSSL

eSSL FL-300 user manual

JAKO

JAKO JKBTNX4 installation guide

Dorma

Dorma MUNDUS PREMIUM GK 50 Mounting instruction

SCOOP

SCOOP Pullbloc 4.1 FS Panik Assembly instruction

Yale

Yale MORTISE 8800 SERIES installation instructions

Siegenia

Siegenia KFV AS3500 Assembly instructions

Installation Guide

Version: 1.0

Date: Jan. 2019

LH7000

1

Lock Diagram

Before Installation

A

BD

G

C

H

O

M

E

I

J

N

F

P

2

Packing List

A N

E JL K G

S

TO

F

CD

B

H

3

Preparing Door

1. Check door thickness; prepare proper screws and spindles.

Note: Please install the mortise (E) according to the above pictures.

EE

EE

Left hand, open inward Right hand, open inward

2. Determining Handing.

Door Thickness D Spindles C Spindle F Screws

38 - 48 mm 40 mm 75 mm 25 mm

Note: If the door is thicker than 38-48 mm, this lock will not be available.

Standpoint

Left hand, open outward Right hand, open outward

The hand of a door is determined from the secure side of the door. The term "secure" means the side from

which you unlock and enter.

4

Cautions

1. New lock is defined as always open mode until it was unlocked once by mifare card.

2. Please swipe authorised card, time sync card, room card at first for the new lock.

3. The lock is equipped with mechanical keys for manual unlocking. Remove the

mechanical keys from the package and keep them in a safe place.

4. To power on the lock, four alkaline AA batteries (not included) are required.

Non-alkaline and rechargeable batteries ARE NOT RECOMMENDED.

5. Do not remove batteries when the lock is in working state.

6. When battery power is low, the lock will beep to remind user to renew the batteries.

Please do not mix up positive and negative while replacing battery.

7. Avoid contacting with corrosive substances, and do not hang objects on the handle.

8. The software within the lock manages the RFID cards, for more details refer to the

software user manual.

9. If there are any questions, please do not hesitate to contact the seller.

5

Installation

desired handle

height

center line of

the handle

door thickness

38~48 mm

backset

54 mm

2. Remove the mortise latch plate (J)

1. Drill holes on the door

Note 1: Align the template along the vertical

center line of the mortise (E) at the desired

handle height, and tape it to door.

Note 2: Mark the holes first, then start drilling.

E

J

I

6

3. Install mortise(E)

F

F

4.Install cylinder(G) and fix

the mortise(E)

G

HI

I

G

H

J

7

5. Install coil spring(B)

B

exterior panel A interior panel N

B

8

6.Install spindle (D) and

exterior panel (A)

D

A

D

7.Install spindle (C) and (D)

D

C

C

D

9

8.Install (N)interior panel

NO

O

9.Install the battery (P)

and plastic cover (M)

P

M