Zavio D-6210 User manual

This manual suits for next models

2

Table of contents

Popular IP Camera manuals by other brands

FLIR

FLIR Exx series user manual

Avigilon

Avigilon H4A-BO1-IR installation guide

Digital Watchdog

Digital Watchdog DWCA-C128-64 manual

ShareTech

ShareTech AV1 user manual

Ezviz

Ezviz C6C quick start guide

Melchioni

Melchioni UCAM 2015 manual

Geutebruck

Geutebruck G-Cam/ESD-4630 quick guide

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG installation manual

Mitel

Mitel 6800i Series Administrator's guide

Vitek

Vitek VTC-IR403-212NP quick start guide

THOMSON

THOMSON DSC - 323W user guide

AVer

AVer FB2027 user manual

ENFORCER

ENFORCER EV-T5105-N2SQ manual

Wansview

Wansview NC543 user manual

Eneo

Eneo MCB-64A0003M0A Quick installation guide

deView electronics

deView electronics CBDNI36F instruction manual

Swann

Swann SwannEye user manual

LevelOne

LevelOne IP CamSecure user manual

0

/ B5210

Eyeball Dome IP Camera

Quick Installation Guide

1

Quick Installation Guide

Please follow the installation steps below to set up your IP Camera.

Check the package contents with the list below. See P.1

Physical overview. See P.2

Installation of hardware and connection of all cables. See P.2

Windows: Go to Zavio website and download Camera Installation Tool. See P.4

Access the IP Camera using Camera Installation Tool. See P.5

MAC OS: using Safari Browser. See P.8

Lighting environment. See P.10

Change language of the web interface. See P.11

Application of IP Camera. See P.12

Package Contents

Camera IP Camera

Quick Installation Guide Brief product information and quick installation

Accessory Alignment Sticker

Screw pack for wall and ceiling mounting

Waterproof connector

Terminal block 2 pin DC connector

Software

The following software and information are available online:

-Video Management Software

-Camera Installation Tool

-User manuals

-Camera Language Packs

You may download the above at http://www.zavio.com/downloads.php or you

may scan the below QR-Code.

To activate Video Management Software, please enter the license key below.

2

Physical Overview

Reset: When the device is powered, press the Reset Button to reboot the device,

or hold the Reset Button for 15 seconds to the settings back to factory default.

Install the hardware and connect all cables

A. Disassemble eyeball dome camera

Twist the outer housing counterclockwise and then remove the outer housing

from the camera base. (see below pictures)

①

②

③

IR LED

Light sensor

3

B. Wall mounting and Ceiling mounting

a. Attach the alignment sticker to the wall/ceiling. Drill four holes into the

wall/ceiling. Hammer the supplied plastic anchors into the screw holes.

b. Place the camera base on the wall/ceiling, pass the cables of the cameras

through the base, and screw the base with the supplied four screws. (see

picture 4)

c. Adjust the camera angle and twist back the outer housing

simultaneously.

d. Optionally screw back the set screws to the outer housing by using the

supplied hex wrench to prevent uninstallation.

C. Connect all cables

C1. Without Power over Ethernet (PoE) connection

1. Connect the power adaptor to the IP Camera.

2. Use a standard RJ-45 network cable and connect the IP Camera to a

hub/switch/router.

④

⑤

⑥

⑦

4

C2. Power over Ethernet (PoE)

1. Use a standard RJ-45 network cable and connect the IP Camera to a

PoE-enabled hub/switch/router.

C3. RJ45 waterproof connector

1. Make sure all components are assembled as shown on the below graph.

2. Check that the Ethernet Port and the Waterproof main body are tightly fasten.

Windows: Go to Zavio Website and download Camera Installation Tool

Please go http://www.zavio.com/softwaredownloads.php download “Camera

Installation Tool”. And follow the installation process to complete the

installation.

5

Access the IP Camera using Camera Installation Tool

1. Please check two settings before using Camera Installation Tool.

a. Browser’s Internet Properties →Security→Default Level

b. Browser’s Internet Properties →Privacy →Uncheck Pop-up Blocker

6

2. Click the Camera Installation Tool Icon on your desktop. The main page will

show up listing all active camera and video server devices. Select the

desired IP cameras from the list and click Link to IE.

3. Enter Username and Password to login to the IP Camera.

(Default is admin / admin)

7

4. When accessing the IP Camera for the first time, a yellow information bar

appears below the address bar: This website wants to install the

following add-on: AxvideoView.cab from ‘Zavio Inc’.

5. Click the information bar, and select Install ActiveX control.

6. Click Install

8

7. Live video will display in the center of your web browser.

MAC OS using Safari Browser

1. Select Safari Icon

9

2. Click Bonjour function and select the camera you wish to access.

3. Enter name and password to login to the IP camera

(Default is admin / admin)