YOKOGAWA TR User manual

User’s

Manual

Mounting and Connecting

TR and TS Hour Meters

Yokogawa Corporation of America

2 Dart Road Newnan, Georgia U.S.A. 30265

Tel: 1-800-258-2552 Fax: 1-770-254-0928

IM 61A00A-01E-A

©Copyright May 1, 2003

1st Edition 5/1/03 1M

TS Series (square face)

Select the mounting configuration from below to determine panel cutout size. Then see opposite page for

outline dimensions.

Model TS-xxxxAx (No bezel-use outline 1, if bezel ordered- use outline 2 or 3).

Model TS-xxxxCx (use outline for mounting option C).

Model TS-xxxxDx (no cutout required. This mounts on DIN rail).

Model TS-xxxxFx (use outline 1 only).

Model TS-xxxxGx (No bezel-use outline 1, if bezel ordered-use outline 2 or 3).

TR Series (round face)

Select mounting configuration below to determine panel cutout dimensions. Then see opposite page for

outline dimensions.

Model TR-xxxxAx (use outline for mounting option A).

Model TR-xxxxCx (use outline for mounting option C).

Model TR-xxxxHx (use outline for mounting option H)

Electrical Wiring

If you have selected combination terminals, or will use the screw terminals for connection, please

observe the following precautions:

1) Use AWG #20 to #26 stranded wire

2) Make sure wire is stripped back 3/8" and wire strands are twisted tight or soldered

3) Loosen non-captive screw no more than 5 full turns

4) Insert wire between pin and clip, then tighten securely,

If you are using the pin connection. Use a 1/4" quick connect female spade lug that has been properly

crimped to wire leads. Slide all the way onto the pin terminal.

Please observe polarity symbols molded into case above terminals.

IM 61A00A-01E-A

50.5+1

Aluminum clamp for TR Series

Mounting A

Cutout 51mm diameter (2.01”)

71+2

42 19

Anti-vibration boot and clamp

Mounting C

Cutout 71mm diameter (2.80”) for TR and TS (square outline not shown)

64.3

3.8

120°

Three screw front mounting for TR Series

Mounting H

Cutout 58mm diameter (2.28”)

45.5 ±0.2

(1.79 ±.01")

ø51

(2.01")

ø50.5 ±0.2

(1.99 ±.01")

45.5 ±0.2

(1.79 ±.01")

Panel Cutout for TS Series

123

This manual suits for next models

Table of contents

Other YOKOGAWA Measuring Instrument manuals

YOKOGAWA

YOKOGAWA 960 34 User manual

YOKOGAWA

YOKOGAWA FLXA402T User manual

YOKOGAWA

YOKOGAWA TA720 User manual

YOKOGAWA

YOKOGAWA 700929 User manual

YOKOGAWA

YOKOGAWA 701977 User manual

YOKOGAWA

YOKOGAWA 960 32 User manual

YOKOGAWA

YOKOGAWA IR400 series User manual

YOKOGAWA

YOKOGAWA CA700-01 User manual

YOKOGAWA

YOKOGAWA Total Insight series User manual

YOKOGAWA

YOKOGAWA SC24V User manual

YOKOGAWA

YOKOGAWA 701989 User manual

YOKOGAWA

YOKOGAWA 700929 User manual

YOKOGAWA

YOKOGAWA wt1600 User manual

YOKOGAWA

YOKOGAWA AQ6374 User manual

YOKOGAWA

YOKOGAWA TB750G Instruction manual

YOKOGAWA

YOKOGAWA MT300 User manual

YOKOGAWA

YOKOGAWA PBDH1000 User manual

YOKOGAWA

YOKOGAWA 73201 User manual

YOKOGAWA

YOKOGAWA SMARTDAC+ GM User manual

YOKOGAWA

YOKOGAWA mR10000 436101 User manual

YOKOGAWA

YOKOGAWA LoRaWAN Sushi Sensor Manual

YOKOGAWA

YOKOGAWA MT300 User manual

YOKOGAWA

YOKOGAWA 7556 User manual

YOKOGAWA

YOKOGAWA FX1000 User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual