YASKAWA DS031 User manual

Yaskawa Electric America, Inc – www.drives.com

02Y00025-0515 Page 1 of 3

Date: 08/28/01

Remote Digital Operator (NEMA 4/12) Option,

Model DS031 & DS033 for GPD 305/J7

Introduction

The remote digital operator kit allows a digital operator to be mounted up to 3 meters from the GPD305/J7. The

kit includes:

1. One remote operator interface attachment

2. One gasket

3. One Digital Operator membrane cover

4. Four screws & nuts

5. Eight rubber washers

6. One RS-232 remote operator interface

7. One cable either 1 meter (DS031) or 3 meter (DS033) in length.

Hardware Installation

WARNING

HAZARDOUS VOLTAGE CAN CAUSE SEVERE INJURY OR DEATH. LOCK ALL POWER

SOURCES DRIVE IN “OFF” POSITION.

1. Disconnect all electrical power to Drive.

2. Verify power has been disconnected by using a voltmeter to check for voltage at incoming power terminals

(L1, L2, and L3).

3. Wait for the DC bus capacitors to completely discharge.

4. Remove contents from package. Verify that the above mentioned parts are included:

5. install the RS-232 remote interface. First, remove the screw on the front cover of the drive. Next, remove the

small square cover located above the control terminals to access CN1. Install the RS-232 remote interface by

positioning the interface directly above the CN2 connector. Press down on interface until all three tabs snap

into place.

6. Re-attach the front cover and tighten the screw down.

Yaskawa Electric America, Inc – www.drives.com

02Y00025-0515 Page 2 of 3

Date: 08/28/01

Remote Digital Operator (NEMA 4/12) Option,

Model DS031 & DS033 for GPD 305/J7

Flush Mounting. Mount the Digital Operator as follows.

1. Cut the Remote Operator mounting panel as shown in Fig. 1.1

Figure 1.1 (Dimensions in Inches, not actual size)

2. Install the Remote Operator on the front side of the panel. Use four stainless screws and four rubber

washers (one rubber washer per screw). See Figure 1.2

FIGURE 1.2

Yaskawa Electric America, Inc – www.drives.com

02Y00025-0515 Page 3 of 3

Date: 08/28/01

Remote Digital Operator (NEMA 4/12) Option,

Model DS031 & DS033 for GPD 305/J7

Surface Mounting. Mount the Digital Operator as follows.

1. Cut the Remote Operator mounting panel as shown in Fig. 2.1

Figure 2.1

(Dimensions in Inches, not actual size)

2. Apply the gasket to the front side of the digital operator. Install the remote operator from the rear side of panel.

Insert the screws through the front side of the panel and then mount the washers and nuts to the rear side of the

panel. Tighten screws gradually from the front side of panel. Refer to figure 2.2 for further installation directions.

3. Connect one end of the cable to the CN1 connector on

the drive and the other end of the cable to the RJ-45

receptacle on the back of the Digital Operator.

This completes the installation process.

Figure 2.1 Remote Operator Installation

This manual suits for next models

Table of contents

Other YASKAWA Controllers manuals

YASKAWA

YASKAWA JEPMC-BUB3005-E User manual

YASKAWA

YASKAWA AC Drive-A1000 User manual

YASKAWA

YASKAWA E7 Drive User manual

YASKAWA

YASKAWA Varispeed DI-16H2 User manual

YASKAWA

YASKAWA SGLGW User manual

YASKAWA

YASKAWA CIMR-VU BA0001 User manual

YASKAWA

YASKAWA PROFINET V1000 User manual

YASKAWA

YASKAWA iQpump1000 Installation manual

YASKAWA

YASKAWA MotionSuite MP940 User manual

YASKAWA

YASKAWA Motoman DX200 User manual

YASKAWA

YASKAWA YRC1000 User manual

YASKAWA

YASKAWA CPCR-MR08C Manual

YASKAWA

YASKAWA Motoman DX200 User manual

YASKAWA

YASKAWA Z1000 CIMR-ZU*A Series User manual

YASKAWA

YASKAWA mp2500 User manual

YASKAWA

YASKAWA Motoman DX200 User manual

YASKAWA

YASKAWA MOTOMAN DX100 User manual

YASKAWA

YASKAWA Servopack CACR-SR Series User manual

YASKAWA

YASKAWA Varispeed-616GII User manual

YASKAWA

YASKAWA Motoman DX200 User manual

YASKAWA

YASKAWA MP3000 Series User guide

YASKAWA

YASKAWA motoman NX100 User manual

YASKAWA

YASKAWA 050-1BA00 User manual

YASKAWA

YASKAWA MP2100 Series User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

3M MicroTouch EX113 reference guide