WamBlee W440 User manual
W440 AIS Sart
Sniffer
Ed. 1.4.0 (EN)
5/2015
Instruction manual
Doc: W440_1_4_0_EN
3
Picture 1: Frontal view
1
4
3
2
4
Picture 2: Schematic diagram
Warning
The crossed rubbish skip symbol indicates that the product should be
wasted separately from the other rubbish at the end of its working life and
that it cannot be thrown together with domestic rubbish.
The user will therefore take the end-life device to the appropriate separate
waste centers of electrical and electronic rubbish indicated by local
authorities.
The proper separate waste of end-life devices for recycling treatment
environmental compatible disposal helps avoiding possible negative
effects on environment and on health supporting the re-use and recycle of
the materials composing the device.
Illegal disposal of the product by the user implies the application of
administrative sanctions provided by law.
WamBlee is a registered trademarks of WamBlee s.r.l
5
EN
Introduction
Congratulations and thank you for purchasing the W440 AIS SART
Sniffer one of the most high-tech reliable devices available on the market.
As the owner of this radio device you are advised to:
•Read this manual.
•Adopt a schedule check planing.
6
EN
Technical specifications
Power supply From 9 to 30 Volts DC
Consumption < 0.1 A typical
Working temperature From -20°C a +55°C
Storage temperature From -30°C a +70°C
Relative Humidity < 70%
Interface NMEA 0183 galvanic isolation
Impedance > 800 Ohms
Speed 38400 baud
AIS Sentence AIVDM
AIS ID in memory Up to 8
Activation Rotary knob switch (Optional)
Auxiliary switch contact or
message
1A 250 VAC
Proprietary NMEA sentence
Dimension DIN 3 module
Weight 130 gr.
Case material PC (UL94 V-0)
IP protections IP4X (Case)
IP2X (Contact)
Installation DIN guide or wall mounting (with accessories)
7
EN
Installation
The W440 AIS Sart Sniffer can be installed on DIN guide (standard model)
or on wall using an adapter kit (on request).
Please note that the W440 is not a waterproof device, and shall be
installed on a protected area.
After W440 mechanical installation you can connect the AIS Sart Sniffer
using copper wire with almost 0.75 mm2 size.
We suggest to use the schematic diagram on page 4.
In detail as for the wire connector marked as (1) (upper part) please see
the following connections :
Pin Connection type and function
1 Positive DC power supply (max +30 Volts)
2 Ground or negative
3 Rotary knob switch lamp.
4 C type rotary knob switch contact (spring return)
5 B type rotary knob switch contact (common)
6 A type rotary knob switch contact (ON mode)
7 N.O. relay contact
8 Common relay contact
9 N.C. relay contact
8
EN
In detail as for the wire connector marked as (4) (lower part) please see
the following connections:
Pin Connection
1 Ground (NMEA out)
2 NMEA proprietary sentence output
3 Buzzer line
4 +V (for special application)
5 Ground
6 NMEA line (A)
7 NMEA line (B)
To the left of the connector are two DIP switches whose function is
explained in the chapter "Using the W440 and its programming."
For connection to the data output of your receiver use the NMEA two
terminals (pin 6 and 7 of the lower connector). This port is capable of
accepting a signal according to the standard NMEA 0183 at 38400 baud.
On the front of the W440 are two indicator lights (LEDs 2 3) Here below is
the table of their functionality.
Led Status Function
Green Fixed on Operative
Red Fixed on AIS Alert received
Red Flashing Speed and communication check during power on
9
EN
Using the W440 and its programming.
The W440 control is made through the use of a three-position switch (2
fixed and one spring return).
Through the switch you can control the operation of your W440 unit which
will operate in this way:
•Position (A) = disabled.
•Position (B) = active device and armed
•Position (C) = selection mode and reset (with spring return to
position B).
The W440 unit is also equipped with two DIP switches located to the left of
the lower connector (4). Their function is the following:
IP Switch Open Close (On position)
1The alarm is activated only if
the AIS ID recognized code is
one of the 8 previously ID
programmed in memory .
(below the procedure for
programming is described).
The alarm is activated if the AIS
received message contains an
ID that starts with 970 or 972
regardless of the rest of the
code.
2Set the line to be used with a
piezo buzzer .
Set the line to be used with a
ON / OFF buzzer (bell or buzzer).
10
EN
Table of contents
