Volt VPL-370 Series User manual
VOLT®Low Voltage Landscape Lighting
VOLT® Pagoda Path Light
VPL- 370 Series
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2019, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 1 -
VOLT®Pagoda Path Light
VPL- 370 Series
INSTALLATION INSTRUCTIONS
www.voltlighting.com
Important: Please Read Before Installation
IMPORTANT SAFETY INSTRUCTIONS
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or
more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are
suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
!
!
- 2 -
Package Contents
Product Dimensions
A. (1) Pagoda Hat C. (1) Stake
B. (1) 6” Stem
4.25”
11.5”
4.75”
Install Stake
1
Board
Stake
Soil
Ground
Determine the desired location for mounting
the luminaire. Hammer the stake into the
ground until ange of stake is ush to grade.
To avoid damage to the stake, place a board on
top of the stake while hammering.
NOTE: If the ground is hard and the stake
is difcult to install, make a crosscut in the
ground using a at shovel.
Parts Required (sold separately)
- 3 -
A. (1) Bulb
VOLT®Pagoda Path Light
VPL-370 Series
Install Stem to Stake
2
Wire Connection
3
6” Stem
Socket
Stake
Pigtail
Wireway Slot
Pigtail
Main Supply Cable
Wire Connectors
Clear away an area in the ground at
the wireway slot on top of the stake.
Lay the luminaire pigtail into the
wireway slot and screw the stem onto
the stake. If the xture does not look
straight, adjust by pushing or pulling
on the stake only.
Strip both leads from the luminaire pigtail. Using two wire connectors
(sold separately), connect the leads from the luminaire to the main low
voltage supply cable leads.
- 4 -
INSTALLATION INSTRUCTIONS
- 5 -
Install/Replace Bulb
Install Bulb
Install Pagoda
4
5
Place the pagoda hat over the bulb
and thread onto the top end of the
stem. Hand tighten until snug.
Socket
Pagoda
Bulb
Bulb
Stem
Insert the bulb with the correct wattage
and type marked on the luminaire label.
CAUTION: Do not exceed maximum
wattage marked on luminaire label.
NOTE: DO NOT touch bulb with bare
hands. Use soft cloth to handle bulb.
Please reverse Step 5 - Step 4 to expose the bulb and replace it with the
correct wattage and type marked on the luminaire label. Reinstall inner
lens and shade.
IMPORTANT: Bi-Pins must be protected from moisture and dust at all times.
Always reinstall shade and lens when moved.
VOLT®Pagoda Path Light
VPL- 370 Series
Replace Lens
2
Remove Pagoda
1
Loosen the pagoda hat and remove it
from the top end of the stem by pulling
it up and over the bulb.
Loosen the screws from the bottom of
the pagoda. Remove the bottom tier
to expose the lens and replace it with
the new replacement shade. Reinstall
the bottom tier to hold the shade and
secure it with the screws removed
previously. Tighten until snug.
Reinstall the pagoda onto the stem.
Stem
Bottom Tier
Screw
Pagoda
Pagoda
Lens
Replace Lens
- 6 -
INSTALLATION INSTRUCTIONS
- 7 -
is-VPL-370-ver5.pdf
Specications and product details subject to change without notice.
© Copyright 2019, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
www.voltlighting.com
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 8 -
Table of contents
Other Volt Landscape Lighting manuals
Volt
Volt 510 Series User manual
Volt
Volt VHS-650-4-BBK User manual
Volt
Volt BRASS BULLY VWL-5 Series User manual
Volt
Volt VFL-430-4-BBK User manual
Volt
Volt VAC-AL-GGT1-BBZ User manual
Volt
Volt VHS-6719-BBZ User manual
Volt
Volt VWL-703-BBZ User manual
Volt
Volt VSDL-6013-BBZ User manual
Volt
Volt VAL-1004-4-BBZ User manual
Volt
Volt VAL-91 Series Operating and safety instructions
Volt
Volt VFL-4007-4-BBZ User manual
Volt
Volt VAL-180 User manual
Volt
Volt VHS-67 Series User manual
Volt
Volt VPL-3024-BBZ User manual
Volt
Volt VAL-2002 User manual
Volt
Volt VPL-1042-4-BBZ User manual
Volt
Volt VAL-9501-4036-BBZ User manual
Volt
Volt VFL-4002-ABZ User manual
Volt
Volt VFL-4601-BBZ User manual
Volt
Volt VSPL-1045-BBZ User manual
Popular Landscape Lighting manuals by other brands
Cooper Lighting
Cooper Lighting MCGRAW-EDISON WBG Specification sheet
Cooper Lighting
Cooper Lighting Invue 42 - 175W Specification sheet
Saxby Lighting
Saxby Lighting Islay 68784 Instruction leaflet
LIGMAN
LIGMAN EU-10016-3 installation manual
Cooper Lighting
Cooper Lighting McGraw-Edison ZD Credenza specification
LIGMAN
LIGMAN KI-60475 installation manual
