Volt VHS-67 Series User manual

VOLT®Low Voltage Landscape Lighting

VOLT® LED Hardscape Lights

VHS-67XX Series

INSTALLATION INSTRUCTIONS

Specications and product details subject to change without notice.

reserved. [email protected] • 813.978.3700

Help Hotline:

1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)

- 1 -

VOLT®LED Hardscape Lights

VHS-67XX Series

Important Safety Instructions: Read Before Installation

INSTALLATION INSTRUCTIONS

www.voltlighting.com

This luminaire is intended for installation in accordance with local codes

and the National Electric Code (NEC). Failure to adhere to these codes and

instructions may result in serious injury, property damage and void the

warranty.

These instructions do not intend to cover all variations in installation,

operation maintenance or mounting situations.

1. Make sure that the power is turned OFF before installing or servicing this

luminaire.

2. Warning: risk of electrical shock. Install all luminaires 10 feet (3.05M) or

more from pool, spa or fountain.

3. This luminaire is intended to be used only with a power supply

(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.

4. DO NOT INSTALL in walls where the capstones overhang the wall less

than 3/4” [19mm] or under stairs where the tread overhangs the riser

less than 3/4” (19mm).

5. Wiring connections must be made with wire connectors that are suitable

for outdoor use.

6. Position the low voltage wire and wire connector so that it is located

within 6 inches (15.2 cm) from a building structure, a luminare, or

tting.

7. The main low voltage cable is intended for shallow burial - less than 6

inches (152 mm).

8. If additional lengths of low voltage cable are required, please contact

www.voltlighting.com or call 1-813-978-3700.

- 2 -

Package Contents

A. (1) Luminaire

B. (2) Self-tapping Screw

C. (2) Wall Anchors

[email protected] • 813.978.3700

- 3 -

Product Dimensions

4.2”

Install Mounting Plate

Brick or

Masonry Wall

Mounting Plate

Barrell Nut

Determine the desired location for

each luminaire before construction

of the wall is started.

Insert the stainless steel mounting

plate (sold separately), in between

the layers of hardscape material.

If prefered, use an adhesive or

mortar (sold separately), to secure

the luminaire in place.

.75”

7.2”

13”

19”

Install Luminaire in Brick or Masonry Wall

.75”

www.voltlighting.com

Install Luminaire

Mounting Plate

Shield

Route the luminaire wire

through the wall to the main

low voltage supply cable using

standard masonry procedures.

A “V” shaped notch can be cut

into the hardscape material

to aide in wire management.

Attach the shield and the

luminaire to the stainless

steel mounting plate by using

machine screws (ships with

mounting plate).

INSTALLATION INSTRUCTIONS

- 4 -

Strip both leads from the luminaire pigtail. Using two wire

connectors (sold separately), connect the leads from the luminaire to

the main supply cable leads.

Luminaire Wires

Main Low Voltage

Supply Cable

Wire Connectors

Wire Connection

VOLT®LED Hardscape Lights

VHS-67XX Series

Luminaire

Mounting Screw

[email protected] • 813.978.3700

- 5 -

Install Luminaire in Railing, Deck Over-hang or Stair

Determine Luminaire Location

Determine the desired location for the luminaire.

Place the luminaire to the mounting surface and mark two points

on the mounting surface where the holes are on the ends of the

luminaire. The marks will be used for self-tapping screws or wall

anchors.

Note: Wall anchors are required for certain installation conditions

(brick wall, concrete wall, etc.)

A wireway hole may be drilled through the decking fascia or other

surface adjacent to the mounting surface.

A. Hold the luminaire in the desired mounting location. Mark the

location where the wire exits the luminaire.

B. Drill a hole through surface (suggested 1/4” [6.5mm] hole).

C. Thread the wire through the drilled hole.

Self-tapping

Screw

Luminaire

Railing, Deck

over-hang or Stair

Mark

Install from Bottom Install from Side

Self-tapping

Screw

Luminaire

Mark

Wireway

Hole

Railing, Deck

over-hang or Stair

Wireway Hole

www.voltlighting.com

INSTALLATION INSTRUCTIONS

- 6 -

VOLT®LED Hardscape Lights

VHS-67XX Series

Install Luminaire

Install the luminaire and shield using provided self-tapping screws.

If the screws are dicult to install, mark holes and drill 1/8” pilot

holes.

If wall anchors are required, drill proper holes from the marks on

the mounting surface and then insert the wall anchors. Then install

the luminaire and shield and secure them with the self-tapping

screws.

Rubber washers are required during installation from the side.

NOTE: DO NOT OVER TIGHTEN SCREWS.

Return to Step 3 to complete the wire connections.

Self-tapping

Screw

Luminaire

Railing, Deck

over-hang or Stair

Mark

Install from Bottom Install from Side

Self-tapping

Screw

Luminaire

Mark

Wireway

Hole

Railing, Deck

over-hang or Stair

Wireway Hole

Shield

Shield Wall Anchor

Rubber

Washer

[email protected] • 813.978.3700

- 7 -

Adjust Lamp Direction

Using an Allen wrench, loosen the set screws on the ends of the

lamp and then rotate the lamp to the desired direction. Always

tighten the set screws after adjustments.

Allen Wrench

Set Screw

Set Screw Lamp

IS-VHS-67XX-ver2.pdf

Specications and product details subject to change without notice.

reserved. [email protected] • 813.978.3700

www.voltlighting.com

Help Hotline:

1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)

- 8 -

This manual suits for next models

Table of contents

Other Volt Landscape Lighting manuals

Popular Landscape Lighting manuals by other brands

Intex

Intex SL1006 owner's manual

LED Group

LED Group ROBUS R2IN13W quick start guide

Patriot Lighting

Patriot Lighting 343-1484 installation manual

Hess

Hess SERA G: SERA S Installation and operating instructions

LIGMAN

LIGMAN JET 44 installation manual

LIGMAN

LIGMAN MALTA 1 installation manual

Cooper Lighting

Cooper Lighting MCGRAW-EDISON WBG Specification sheet

Cooper Lighting

Cooper Lighting Invue 42 - 175W Specification sheet

Saxby Lighting

Saxby Lighting Islay 68784 Instruction leaflet

LIGMAN

LIGMAN EU-10016-3 installation manual

Cooper Lighting

Cooper Lighting McGraw-Edison ZD Credenza specification

LIGMAN

LIGMAN KI-60475 installation manual

Cooper Lighting

Cooper Lighting Generation CLB25MWW5C373 Specification sheet

Malibu Boats

Malibu Boats CL905K instructions

LIGMAN

LIGMAN NYB-30161 installation manual

LIGMAN

LIGMAN SI-80021 installation manual

Malibu Boats

Malibu Boats CM110P instructions

U.S.T.E.

U.S.T.E. VISTA 8202 installation instructions