Volt VFL-4007-4-BBZ User manual
VOLT®Low Voltage Landscape Lighting
VOLT®Wide Splash R7S Flood Light
VFL-4007-4-BBZ
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2019, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 1 -
Important: Please Read Before Installation
INSTALLATION INSTRUCTIONS
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are
suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or
tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
7. If additional lengths of low voltage cable are required, please contact
www.voltlighting.com or call 1-813-978-3700.
!
www.voltlighting.com
Important Safety Instructions
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
!
- 2 -
VOLT®Wide Splash R7S Flood Light
VFL-4007-4-BBZ
Package Contents
Product Dimensions
A. (1) Fixture Body
- 3 -
6.42” 3.75”
3.15”
2”
Install Stake
1
Determine the desired location
for mounting the xture.
Hammer the stake into the
ground until ange of stake
is ush to grade. To avoid
damage to the stake, place a
board on top of the stake while
hammering.
Note: If the ground is hard and
the stake is difcult to install,
make a crosscut in the ground
using a at shovel.
Board
Ground
Soil
Stake
INSTALLATION INSTRUCTIONS
www.voltlighting.com
- 4 -
Install Fixture Body to Stake
2
Clear away an area in the
ground at the wireway slot on
top of the stake. Lay the supply
wires into the wireway slot and
screw the xture body on to the
stake. Tighten until snug.
Fixture Body
Ground
Supply Wires
Wireway Slot
Soil
Stake
Wire Connection
3
Strip both leads from the luminaire pigtail. Using two wire connectors
(sold separately), connect the leads from the luminaire to the main
supply cable leads.
Pigtail
Main Supply
Cable
Wire Connectors
VOLT®Wide Splash R7S Flood Light
VFL-4007-4-BBZ
- 5 -
Remove Glare Guard
4
Loosen the set screws and remove the glare guard from the xture body.
Fixture Body
Set Screw
Glare Guard
Install R7S Bulb
5
Insert the R7S bulb with the
correct wattage and type
marked on the xture label and
push into place.
CAUTION: Do not exceed
maximum wattage marked on
luminaire label.
Bulb Base
R7S Bulb
R7S Bulb
Rotate
Before installing the glare guard back onto the xture, adjust the R7S
bulb.
Rotate the bulb inside it’s socket towards the back of the xture to
decrease the light output. To return to the normal lumen output, rotate
the bulb towards the lens.
INSTALLATION INSTRUCTIONS
www.voltlighting.com
- 6 -
VOLT®Wide Splash R7S Flood Light
VFL-4007-4-BBZ
ROTATE
Adjust Fixture Direction
7
Fixture
Set Screw
Then place the glare guard back onto the xture body and secure with the
previously removed set screws. Hand tighten until snug.
Fixture
Body
Set Screw
Glare Guard
Install Glare Guard
6
Loosen the set screw and
adjust the xture to the
desired direction. Once the
desired direction is achieved,
tighten the set screw until
snug.
- 7 -
Install/Replace Bulb
Remove the glare guard to expose the R7S bulb and replace it
with the correct wattage and type marked on the xture label. Then,
reinstall the glare guard.
IMPORTANT: R7S bulb must be protected from moisture and dust at all
times. Always reinstall the glare guard when removed.
- 8 -
Specications and product details subject to change without notice.
© Copyright 2019, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
www.voltlighting.com
IS-VFL-4007-ver1.pdf
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
Table of contents
Other Volt Landscape Lighting manuals
Volt
Volt VAL-2015-BBZ User manual
Volt
Volt VSAC-PANEL1-SBK User manual
Volt
Volt VAL-91 Series Operating and safety instructions
Volt
Volt VSM-2407 User manual
Volt
Volt VAL-2102-0-BBZ User manual
Volt
Volt VSPL-9001-25-BBZ User manual
Volt
Volt VFL-40 MS-ABZ Series User manual
Volt
Volt VFL-4601-4-BBZ User manual
Volt
Volt RGBW BuddyPro VHS-6725-0-BRB User manual
Volt
Volt Guardsman VPL-1011 User manual
Volt
Volt VPL-1048-4-BBZ User manual
Volt
Volt VFL-4501-4-BBZ User manual
Volt
Volt VWL-703-BBZ User manual
Volt
Volt VAL-2002 User manual
Volt
Volt STK-17LI Series User manual
Volt
Volt VSPL-1047-BBZ User manual
Volt
Volt VAL-2049-35-4-BBZ User manual
Volt
Volt VAL-1811-40-BBZ User manual
Volt
Volt VAL-2001 Series User manual
Volt
Volt VWL-703 User manual
Popular Landscape Lighting manuals by other brands
Cooper Lighting
Cooper Lighting MCGRAW-EDISON WBG Specification sheet
Cooper Lighting
Cooper Lighting Invue 42 - 175W Specification sheet
Saxby Lighting
Saxby Lighting Islay 68784 Instruction leaflet
LIGMAN
LIGMAN EU-10016-3 installation manual
Cooper Lighting
Cooper Lighting McGraw-Edison ZD Credenza specification
LIGMAN
LIGMAN KI-60475 installation manual
