Volt VHS-6719-25-BBZ User manual

VOLT®Low Voltage Landscape Lighting

VOLT® 18” High Output Brass Rotatable LED Hardscape Light

VHS-6719-25-BBZ

INSTALLATION INSTRUCTIONS

Specications and product details subject to change without notice.

reserved. [email protected] • 813.978.3700

Help Hotline:

1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)

- 1 -

VOLT® 18” High Output Brass Rotatable LED Hardscape Light

VHS-6719-25-BBZ

Important Safety Instructions: Read Before Installation

INSTALLATION INSTRUCTIONS

www.voltlighting.com

This luminaire is intended for installation in accordance with local codes and

the National Electric Code (NEC). Failure to adhere to these codes and

instructions may result in serious injury, property damage and void the

warranty.

These instructions do not intend to cover all variations in installation, opera-

tion maintenance or mounting situations.

1. Make sure that the power is turned OFF before installing or servicing this

luminaire.

2. Warning: risk of electrical shock. Install all luminaires 10 feet (3.05M) or

more from pool, spa or fountain.

3. This luminaire is intended to be used only with a power supply

(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.

4. DO NOT INSTALL in walls where the capstones overhang the wall less

than 3/4” [19mm] or under stairs where the tread overhangs the riser

less than 3/4” (19mm).

5. Wiring connections must be made with UL listed wire connectors that is

suitable for outdoor use.

6. Position the low voltage wire and UL listed wire connector so that it is

located within 6 inches (15.2 cm) from a building structure, a luminare,

or tting.

7. The main low voltage cable is intended for shallow burial - less than 6

inches (152 mm).

- 2 -

Product Dimensions

Package Contents

A. (1) Luminaire

B. (2) Stainless Steel Screws

19”

[email protected] • 813.978.3700

- 3 -

Install Mounting Plate

Optional: Install Glare Guard Before Installation

Install Luminaire in Brick or Masonry Wall

If you choose, you can attach the

glare guard rst before mounting

the xture.

Use the screws and washers to

secure the glare guard onto the

xture. Tighten with a

screwdriver.

Screw

Washer

Brick or

Masonry Wall

Mounting Plate

Barrell Nut

Determine the desired location for

each luminaire before construction

of the wall is started.

Insert the stainless steel mounting

plate (sold separately), in between

the layers of hardscape material.

If preferred, use an adhesive or

mortar (sold separately), to secure

the luminaire in place.

Install Luminaire

Mounting Plate

Glare Guard

Luminaire

Mounting Screw

Route the luminaire wire

through the wall to the main

low voltage supply cable using

standard masonry procedures.

A “V” shaped notch can be cut

into the hardscape material

to aide in wire management.

Attach the glare guard and

the luminaire to the stainless

steel mounting plate by using

mounting screws (ships with

mounting plate).

www.voltlighting.com

INSTALLATION INSTRUCTIONS

- 4 -

Wire Connection

VOLT® 18” High Output Brass Rotatable LED Hardscape Light

VHS-6719-25-BBZ

Adjust Lamp Direction

Strip both leads from the luminaire pigtail. Using two UL listed wire

connectors (sold separately), connect the leads from the luminaire to

the main supply cable leads.

* We recommend ace heat shrink style connectors for hardscape

connections.

Main Low Voltage

Supply Cable

Luminaire Wires

Wire Connectors

Set Screw Lamp

Using an Allen wrench, loosen the set screws on the ends of the

lamp and then rotate the lamp to the desired direction. Always

tighten the set screws after adjustments.

[email protected] • 813.978.3700

- 5 -

Install Luminaire in Railing, Deck Over-hang or Stair

Determine Luminaire Location

Self-tapping

Screw

Luminaire

Railing, Deck

over-hang or Stair

Mark

Install from Bottom Install from Side

Self-tapping

Screw

Luminaire

Mark

Wireway

Slot

Railing, Deck

over-hang or Stair

Wireway Slot

Determine the desired location for the luminaire.

Place the luminaire to the mounting surface and mark two points

on the mounting surface where the holes are on the ends of the

luminaire. The marks will be used for self-tapping screws or wall

anchors.

Note: Wall anchors are required for certain installation conditions

(brick wall, concrete wall, etc.)

A wireway hole may be drilled through the decking fascia or other

surface adjacent to the mounting surface.

A. Hold the luminaire in the desired mounting location. Mark the

location where the wire exits the luminaire.

B. Drill a hole through surface (suggested 1/4” [6.5mm] hole).

C. Thread the wire through the drilled hole.

www.voltlighting.com

INSTALLATION INSTRUCTIONS

- 6 -

VOLT® 18” High Output Brass Rotatable LED Hardscape Light

VHS-6719-25-BBZ

Install Luminaire

Self-tapping

Screw

Luminaire

Railing, Deck

over-hang or Stair

Mark

Install from Bottom Install from Side

Self-tapping

Screw

Luminaire

Mark

Wireway

Hole

Railing, Deck

over-hang or Stair

Wireway Hole

Glare Guard

Glare

Guard

Wall Anchor

Rubber

Washer

Install the luminaire and glare guard using provided self-tapping

screws. If the screws are dicult to install, mark holes and drill

1/8” pilot holes.

If wall anchors are required, drill proper holes from the marks on

the mounting surface and then insert the wall anchors. Then install

the luminaire and glare guard and secure them with the self-

tapping screws.

Rubber washers are required during installation from the side.

NOTE: DO NOT OVER TIGHTEN SCREWS.

[email protected] • 813.978.3700

Wire Connections

Strip both leads from the luminaire pigtail. Using two UL listed wire

connectors (sold separately), connect the leads from the luminaire to

the main supply cable leads.

* We recommend ace heat shrink style connectors for hardscape

connections.

Main Low Voltage

Supply Cable

Luminaire Wires

Wire Connectors

Adjust Lamp Direction

Set Screw Lamp

Using an Allen wrench, loosen the set screws on the ends of the

lamp and then rotate the lamp to the desired direction. Always

tighten the set screws after adjustments.

Install Luminaire toY Bracket

Determine Luminaire Location

Place the luminaire onto the

Y bracket using the rubber

washers and screws.Tighten

with a screwdriver.

Y Bracket

Luminaire

Screw

Rubber Washer

- 7 -

www.voltlighting.com

- 8 -

INSTALLATION INSTRUCTIONS

VOLT® 18” High Output Brass Rotatable LED Hardscape Light

VHS-6719-25-BBZ

Install Riser

Luminaire

Pass the supply wire from the

luminaire through the center

hole on the Y bracket and the

riser.Then thread the riser

onto the Y bracket and hand

tighten until snug.

Supply Wire

Riser

Y Bracket

Install Stake

Determine the desired location

for mounting the stake. Hammer

the stake into the ground until

ange of stake is ush to grade.

To avoid damage to the stake,

place a board on top of the stake

while hammering.

Note: If the ground is hard and

the stake is difcult to install,

make a crosscut in the ground

using a at shovel.

Board

Ground

Soil

Stake

[email protected] • 813.978.3700

- 9 -

Intsall Riser to Stake

Supply Wire

Clear away area in the ground

at wireway slot on the top of

the stake. Pass the xture supply

wire through the center hole of the

stake and lay it into

the wireway slots.Thread the

riser onto the stake. Hand

tighten until snug.

Riser

Ground

Soil

Stake

Wire Connections

Strip both leads from the luminaire pigtail. Using two UL listed wire

connectors (sold separately), connect the leads from the luminaire to

the main supply cable leads.

* We recommend ace heat shrink style connectors for hardscape

connections.

Main Low Voltage

Supply Cable

Luminaire Wires

Wire Connectors

www.voltlighting.com

- 10 -

INSTALLATION INSTRUCTIONS

VOLT® 18” High Output Brass Rotatable LED Hardscape Light

VHS-6719-25-BBZ

Adjust Lamp Direction

Allen Wrench

Set Screw

Set Screw Lamp

Using an Allen wrench, loosen the set screws on the ends of the

lamp and then rotate the lamp to the desired direction. Always

tighten the set screws after adjustments.

This manual suits for next models

Table of contents

Other Volt Landscape Lighting manuals

Popular Landscape Lighting manuals by other brands

Intex

Intex SL1006 owner's manual

LED Group

LED Group ROBUS R2IN13W quick start guide

Patriot Lighting

Patriot Lighting 343-1484 installation manual

Hess

Hess SERA G: SERA S Installation and operating instructions

LIGMAN

LIGMAN JET 44 installation manual

LIGMAN

LIGMAN MALTA 1 installation manual

Cooper Lighting

Cooper Lighting MCGRAW-EDISON WBG Specification sheet

Cooper Lighting

Cooper Lighting Invue 42 - 175W Specification sheet

Saxby Lighting

Saxby Lighting Islay 68784 Instruction leaflet

LIGMAN

LIGMAN EU-10016-3 installation manual

Cooper Lighting

Cooper Lighting McGraw-Edison ZD Credenza specification

LIGMAN

LIGMAN KI-60475 installation manual

Cooper Lighting

Cooper Lighting Generation CLB25MWW5C373 Specification sheet

Malibu Boats

Malibu Boats CL905K instructions

LIGMAN

LIGMAN NYB-30161 installation manual

LIGMAN

LIGMAN SI-80021 installation manual

Malibu Boats

Malibu Boats CM110P instructions

U.S.T.E.

U.S.T.E. VISTA 8202 installation instructions