Volt VAL-2001 Series User manual
VOLT®Low Voltage Landscape Lighting
VOLT® All-StarTM Mini
VAL-2001 Series
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2019, VOLT® Lighting, Lutz FL USA 33549 • All rights
reserved. [email protected] • 813.978.3700
- 1 -
VOLT® All-StarTM Mini
VAL-2001
Important: Please Read Before Installation
Important Safety Instructions
INSTALLATION INSTRUCTIONS
LIGHTED LAMP IS HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before reducing lamp.
2. Lamp gets HOT quickly!
3. Do not touch the hot lens, guard or cowl.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time.
6. Use a soft cloth.
7. Oil from skin may damage lamp.
8. Do not operate the xture with a damaged or missing lens or shield.
!
!
www.voltlighting.com [email protected] • 813.978.3700
Package Contents
Parts Required
A. (1) MR11 Lamp (sold separately)
Product Dimensions
Remove Glare Guard and Shield from Fixture
1
Glare Guard
Set
Screw
Shield
Fixture
Unlock the set screw and remove the
glare guard from the shield. Loosen
the shield and remove it from the
xture.
2.75”
4.5”
2.75”
1.75”
- 3 -- 2 -
This luminaire is intended for installation in accordance with local codes and the
National Electric Code (NEC). Failure to adhere to these codes and instructions
may result in serious injury, property damage and void the warranty.
These instructions do not intend to cover all variations in installation, operation
maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or
more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with wire connectors that are suitable
for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
7. If additional lengths of low voltage cable are required, please contact
www.voltlighting.com or call 1-813-978-3700.
A. Fixture
B. Stake
INSTALLATION INSTRUCTIONS
www.voltlighting.com [email protected] • 813.978.3700
Install MR11 Lamp
Install Glare Guard and Shield to Fixture
2
3
Insert the lamp with the correct
wattage and type marked on the
xture label.
CAUTION: Do not exceed
maximum wattage marked on
luminaire label.
NOTE: DO NOT touch lamp with
bare hands. Use soft cloth to
handle lamp.
Attach the shield back onto the
xture. Place the glare guard over
the shield and secure with the set
screw. Tighten until snug.
Socket
MR11 Lamp
(sold
separately)
Clear away an area in the ground
at the wireway slot on top of
the stake. Lay the luminaire
pigtail into the wireway slot and
screw the xture onto the stake.
Tighten until snug.
Install Fixture to Stake
5
Fixture
Pigtail
Wireway Slot
Stake
Install Stake
4
Board
Stake
Soil
Ground
Determine the desired location for
mounting the xture. Hammer the
stake into the ground until ange of
stake is ush to grade. To avoid damage
to the stake, place a board on top of
the stake while hammering.
NOTE: If the ground is hard and the
stake is difcult to install, make a
crosscut in the ground using a at
shovel.
Glare Guard
Set
Screw
Shield
Fixture
- 5 -- 4 -
VOLT® All-StarTM Mini
VAL-2001
INSTALLATION INSTRUCTIONS
www.voltlighting.com [email protected] • 813.978.3700
Install/Replace Lamp
Remove the glare guard and the shield to expose the lamp and
replace it with the correct wattage and type marked on the xture
label. Then reinstall the shield and the glare guard to the xture.
IMPORTANT: Halogen lamps must be protected from moisture and
dust at all times. Always reinstall the shield when moved.
Wire Connections
6
Strip both leads from the luminaire pigtail. Using two wire connectors
(sold separately), connect the leads from the luminaire to the main
supply cable leads.
Pigtail
Main Supply Cable
Wire Connectors
- 7 -- 6 -
VOLT® All-StarTM Mini
VAL-2001
is-VAL-2001-ver3.pdf
Specications and product details subject to change without notice.
© Copyright 2019, VOLT® Lighting, Lutz FL USA 33549 • All rights
reserved. [email protected] • 813.978.3700
www.voltlighting.com
- 8 -
This manual suits for next models
1
Other Volt Landscape Lighting manuals
Volt
Volt 3601 Series User manual
Volt
Volt VSDL-6013-BBZ User manual
Volt
Volt VPL-3024-BBZ User manual
Volt
Volt VSM-2408-0-BBZ User manual
Volt
Volt VAL-2015-BBZ User manual
Volt
Volt VPL-1019-26-4-BBZ User manual
Volt
Volt VPL-1011-4-BBZ User manual
Volt
Volt RGBW BuddyPro VHS-6725-0-BRB User manual
Volt
Volt VPL-1048-4-BBZ User manual
Volt
Volt 510 Series User manual
Volt
Volt VDL-6008-4-BBZ User manual
Volt
Volt VAL-1810-40-BBZ User manual
Volt
Volt VFL-4002-ABZ User manual
Volt
Volt VAL-180 User manual
Volt
Volt VSPL-1045-BBZ-R1 User manual
Volt
Volt VSM-2407 User manual
Volt
Volt VAL-2101-0-BBZ User manual
Volt
Volt VFL-4001-LI-ABZ User manual
Volt
Volt VHS-668-4-BBZ User manual
Volt
Volt VWL-500-4-PBK User manual
Popular Landscape Lighting manuals by other brands
Cooper Lighting
Cooper Lighting MCGRAW-EDISON WBG Specification sheet
Cooper Lighting
Cooper Lighting Invue 42 - 175W Specification sheet
Saxby Lighting
Saxby Lighting Islay 68784 Instruction leaflet
LIGMAN
LIGMAN EU-10016-3 installation manual
Cooper Lighting
Cooper Lighting McGraw-Edison ZD Credenza specification
LIGMAN
LIGMAN KI-60475 installation manual
