VOH VISIOTEST User manual

V9.0, 06.07.2018

VISIOTEST

USER GUIDE

VOH SA

GU-04-06-01

User guide

VISIOTEST

Version 8.0

Created 12/2017

Page 2 / 27

Table of Contents:

1GENERAL INFORMATION ............................................................................................................................................3

1.1 GUARANTEE....................................................................................................................................................................3

1.2 SECURITY .......................................................................................................................................................................3

1.3 TRANSPORT ....................................................................................................................................................................4

1.4 STORAGE........................................................................................................................................................................4

2PRODUCT DESCRIPTION ..............................................................................................................................................5

3CONTENTS AND ADDITIONAL OPTIONS.......................................................................................................................6

4USER INTERFACE .........................................................................................................................................................7

4.1 HMI PANEL CONNECTORS.................................................................................................................................................7

4.2 FUNCTIONS.....................................................................................................................................................................7

4.3 DEVICE SETTINGS.............................................................................................................................................................8

4.4 START SCREEN .................................................................................................................................................................9

4.4.1 Administrator Mode and SAV access ..........................................................................Erreur ! Signet non défini.

4.5 ADMINISTRATOR MODE ..................................................................................................................................................10

4.5.1 Adding a sensor.................................................................................................................................................12

4.5.2 Add Program .....................................................................................................................................................13

4.5.3 Import / Export sensors (and their programs) ..................................................................................................14

4.5.4 Administrator Mode: Main screen ....................................................................................................................15

4.6 USER MODE .................................................................................................................................................................16

4.6.1 Control Mode / Production Mode .....................................................................................................................18

4.6.2 Statistic module ................................................................................................................................................19

4.6.3 Measurement History Access............................................................................................................................20

4.6.4 Additional Functions and Transfer of DATA ......................................................................................................21

4.7 TRANSFER RESULTS VIA USB CABLE ...................................................................................................................................23

4.8 SERVICE (SAV) MODE ....................................................................................................................................................25

4.8.1 Calibration of FORCETEST sensors ....................................................................................................................25

4.8.2 Torque sensors calibration ................................................................................................................................26

5EXCLUSION OF RESPONSIBILITY AND/OR GUARANTEE .............................................................................................27

6MAINTENANCE AND SERVICE....................................................................................................................................27

7REPRESENTATION/DISTRIBUTION .............................................................................................................................27

Track changes :

Version

Date

Written

Change

Validated

Approved

V8.0

01.12.2017

JSA/BAP

Update V3.01 SW

V9.0

06.07.2018

BAP

Update V4.01 SW (.csv, basic mode,

units)

VOH SA

GU-04-06-01

User guide

VISIOTEST

Version 8.0

Created 12/2017

Page 3 / 27

1 General information

1.1 Guarantee

VOH SA warrants this product against any defects in manufacturing or in materials under normal conditions of

use and service for a duration of two years from the date of commissioning at the client’s premises. If, at any time

during the guarantee period, the product is found to be defective or fails, VOH SA shall repair or replace it (at the

discretion of VOH SA).

If the product is defective, please call VOH Customer Service on +41(32) 945 17 45.

The warranty shall not apply if VOH SA proves the default or failure is due to improper use of the equipment.

The product is equipped with seals of warranty. Breaking or severing these seals leads to cancellation of the

warranty.

Figure 1: Seal of warranty

The scope of VOH SA’s liability is limited to the repair or the replacement of the product under the terms set out

above.

VOH SA SHALL NOT BE HELD LIABLE FOR ANY LOSS OR DAMAGES, INCLUDING INCIDENTAL OR

CONSEQUENTIAL DAMAGES ARISING DIRECTLY OR INDIRECTLY FROM A BREACH OF THE

GUARANTEE, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. THIS GUARANTEE

IS THE ONLY EXPRESS GUARANTEE PROVIDED BY VOH SA FOR THIS PRODUCT.

This guarantee only covers the initial buyer and is not transferable.

If you have any questions regarding the guarantee, please write to VOH SA at the following address:

VOH SA

La Praye 5a

CH-2608 Courtelary

Telephone: +41(32) 945 17 45

Fax: +41(32) 945 17 55

e-Mail: custom[email protected]

Internet: http://www.voh.ch

1.2 Security

Notice

Do not use the VISIOTEST if it has been damaged. Prior to starting up the machine, first inspect its

control box and electrical connections.

The VISIOTEST must be used in accordance with the specified guidelines of the fabricator (VOH SA).

Only personnel who have been properly formed in the user procedure, and have read this document

should use the VISIOTEST.

VOH SA

GU-04-06-01

User guide

VISIOTEST

Version 8.0

Created 12/2017

Page 4 / 27

Warning!!!

Please carefully read the information contained in this manual before using the device. Improper use

could severely damage the system or peripheral devices.

The VISIOTEST must be used in an industrial environment.

Before connecting the device for the first time, verify that the voltage corresponds to the suggested

voltage for the device (see the attached label)

In the instance that the machine is not used for a prolonged period of time, disconnect the power cable.

Do not under any circumstances take apart the VISIOTEST machine. Only the manufacture, VOH SA, is

entitled to repair or replace defective components.

This product should only be stored and employed at a room temperature not falling below 10°C or

exceeding 40°C (50-104 °F).

This User Guide must be kept in close proximity to the machine.

Please use only electric cables that correspond to the requirements of the VISIOTEST.

DO not place the VISIOTEST in close proximity to a heat source.

1.3 Transport

It is suggested that when transported over long or short distances that shock-preventative packaging (provided

upon delivery of the machine) is used.

1.4 Storage

The VISIOTEST must be stored in a dry place, protected from humidity and dust. The storage temperature

should not fall below 10°C (50° F), or surpass 40°C (104 °F).

VOH SA

GU-04-06-01

User guide

VISIOTEST

Version 8.0

Created 12/2017

Page 5 / 27

2 Product description

The VISIOTEST is a display unit for torque and force sensors. It is compatible with Atlas-Copco Microtorque,

Torquetest VOH and Forcetest VOH sensors (See Figure 2).

Technical specifications

Dimensions and weight

180mm x 100mm x

135mm (w x d x h) / 0.5

Weight with power supply and cable

2kg

VOH SA

GU-04-06-01

User guide

VISIOTEST

Version 8.0

Created 12/2017

Page 6 / 27

3 Contents and additional options

Description

VISIOTEST and universal stylus pen for touch screen

Power supply 24V(input 110-240VAC, 50-60 Hz)

Power supply cord for CEE devices

User Guide

Figure 2: VISIOTEST and peripheral devices

VOH SA

GU-04-06-01

User guide

VISIOTEST

Version 8.0

Created 12/2017

Page 7 / 27

4 User Interface

4.1 HMI Panel Connectors

Figure 3: HMI VISIOTEST connectors

4.2 Functions

The VISIOTEST functions using a four-tier system of access:

- Basic: open access, no programming required

- User : open access, programming required

- Programming mode (admin) : password protected access

- SAV : password protected access

The diagram below depicts the basic functions of the device. Each function is presented in greater detail in the

paragraphs that follow.

Figure 4: Diagram of general functions of the VISIOTEST

Access to Programming (admin) Mode and SAV Mode is password protected. It is in Programming Mode that it is

possible to add, modify, or delete sensors and/or programs. These functions are presented in the following

paragraphs.

VOH SA

GU-04-06-01

User guide

VISIOTEST

Version 8.0

Created 12/2017

Page 8 / 27

4.3 Device Settings

To access device settings, it is necessary to click on the settings icon while the device is starting up (démarrage).

Figure 5: Screen during start up (Settings icon at top left)

From the Settings screen, users can modify language, date and time, select a printer, and change the password

for Administrator Mode.

Figure 6: VISIOTEST Settings

This configuration screen is for choosing after how much time of inactivity the brightness of the screen will be

reduced and at which intensity. Any click on the screen will set it back to full brightness.

Figure 7: Screensaver configuration

VOH SA

GU-04-06-01

User guide

VISIOTEST

Version 8.0

Created 12/2017

Page 9 / 27

4.4 Start screen

4.4.1Sensor list or basic measure access

Once the VISIOTEST has completed starting up, the home screen will appear. When a torque sensor (button

with “Nm” unit) and a force sensor (button with “N”) are connected, the screen in figure 8 is displayed.

Figure 8: Welcome screen (Information icon at top left)

The button on the right gives access to the list of connected sensor and their programs. The two other buttons

allows access to the “basic” measurement mode for each type of sensor connected.

If no or only 1 sensor is connected, the screens are presented according to the possibilities below:

Figure 9: Welcome screen (variation according to the connected sensors)

To access the info page or SAV, first select the Information icon. A selection of information relative to the

different functions of the device will appear on the screen. Select the SAV icon to access the Password login

screen.

Default password for SAV Mode: 1397

Figure 10: Administrator Mode/ SAV access

VOH SA

GU-04-06-01

User guide

VISIOTEST

Version 8.0

Created 12/2017

Page 10 / 27

4.5 Mode “Basic measurement”

This mode allows direct and simple measurement via one of the connected sensors.

Figure 11: Mode basic : on the left, a sensor with positive FSR, on the right with a +/- FSR

Symbols and buttons description :

Instantaneous value display

Display of the maximum measured value and possibly minimum value

in the case of a sensor in +/-

Send measurement data button (RS-232, USB and SD save)

Resetting the measurement

Table of contents

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual