Vitek VTC-TNB42R3F User manual

VITEK

FEATURES

• 1/3” 3.0 Megapixel Progressive Scan CMOS image sensor

• Up to 30fps live view @ 1920x1080 (2MP) / 15fps live

view @ 2048x1536 (3MP)

• 2.8~12mm Varifocal Lens (VTC-TNB36R3V) / 3.6mm

Fixed Iris Lens (VTC-TNB42R3F)

• 42 Infrared LED’s with 150’ IR Range (VTC-TNB42R3F) /

36 Infrared LED’s with 120’ IR Range (VTC-TNB36R3V)

• Wide Dynamic Range (WDR)

• True Mechanical Day/Night function by ICR

• 3D-DNR Noise Reduction

• On Board Motion Detection

• H.264/MJPEG Dual Streaming

• Onvif Compliance

• Remote Viewing via CMS, Web Browser, and iOS & Android

Apps

• Minimal Latency with up to 10 simultaneous user

connections

• IP66 Weather Resistance

• 12VDC & PoE (Power over Ethernet) Operation

VTC-TNB42R3F

VTC-TNB36R3V

3.0 Megapixel Indoor/Outdoor

WDR IP IR Bullet Cameras

QUICK START GUIDE

*Refer to included CD for complete detailed User’s Manual.

2 3

Lens

Sun Shield

Mount Lock

Mount Base

RJ-45 Ethernet

Power Cable

Lens Cover

Zoom*

Focus*

Components and Accessories

Overview

This camera series supports both fixed and varifocal lenses. Please note

that the zoom and focus features mentioned below are only available on

the varifocal lens version.

*Optional

3 4

Camera

Quick Guide

Screws

Drill Template

Product Manual CD

Waterproof Cap

Network Cable & Power Connections

Cable / Network Configuration

First connect the Waterproof Cap to an Ethernet patch cable, then

connect the cameras ethernet adaptor. If not powering the camera with

PoE, also connect the power Cable to an approved 12VDC Power

Supply.

12VDC

Optional 12VDC

Power Connection.

Not needed with PoE

12VDC

Router

Internet

Modem

Computer

Network Cable

4 5

Installation

Before start, please make sure that the wall or ceiling is strong enough

to withstand 3 times the weight of the camera. The mounting steps are

as follows:

1. Attach the drill template to

the place where you want to

install the camera, then drill

3 screw holes and 1 cable

hole (if you want to route the

cables through the mounting

base) according to the drill

template

2. Route the cables and connect the power & video cables, then secure

the mounting base to the ceiling or wall with screws.

Ceiling Mounted Wall Mounted

Installation

3. Loosen the mount lock to adjust the Pan and Tilt of the camera, then

tighten the mount lock to secure the viewing angle adjustments.

4. To adjust the lens, start by removing the Lens Cover, then adjust

the Focus and Zoom levers to achieve a clear image. Replace

the Lens Cover. (if your camera is Fixed lens, please skip this

step)

5. Carefully remove the protective film from the lens to complete the

installation.

90° Tilt

360° Pan

Zoom

Focus

Lens Cover

6 7

LAN Configuration

The camera can be accessed on the local network either using the

IP-Tool or directly in a web browser.

1. Attach the drill template to the place where you want to install the

camera, then drill 3 screw holes and 1 cable hole (if you want to

route the cables through the mounting base) according to the drill

template

Accessing the Camera Using the IP-Tool

1. Make sure the camera and PC are connected to the LAN.

2. Locate the IP-Tool installer on the included Product Documentation

CD, then install on the PC. Open the installed application.

3. Modify the IP address. The default IP address is 192.168.226.201.

Click the information of the camera listed in the above table to show

the network information on the right side. Modify the IP address and

gateway of the camera and make sure its network address is in the

same local network segment as the computer’s. Please modify the

IP address of your device according to the practical situation.

For example, the IP address of your computer

is 192.168.13.4. So the IP address of the

camera shall be changed to 192.168.13.X.

After modification, please input the password

of the administrator and click “Modify” button

to modify the setting.

** Default admin password: “123456".

4. Double-click the IP address and then the system will pop up the web

browser to connect IP-CAM . IE browser will download the Active X

control automatically. After downloading, a login window will pop up

as shown below:

Input the user name and password to log in.

Default user name: admin / Default password: 123456.

Directly Access Through a Web Browser

The default network settings are as shown below:

IP address: 192.168.226.201 HTTP: 80

Subnet Mask: 255.255.255.0 Data Port: 9008

Gateway: 192.168.226.1

You may use the above default settings when you log in the camera for

the first time.

1. Manually set the IP address of the PC and the network segment

should be as the same as the default settings of IP-CAM. Open the

network and share center. Click “Local Area Connection” to pop up

the following window.

Select “Properties” and then select Internet protocol according to the

actual situation (for example: IPV4). Next, click “Properties” button to

set the network of the PC.

2. Open the IE Browser and input the default address of IP-CAM and

confirm. The IE browser will download Active X control automatical-

ly.

3. After downloading Active X control, the login dialog box will pop up.

4. Input the default username and password and then enter to view.

WAN Configuration

Access the camera by the router or virtual server for example.

1. Make sure the camera is connected to the LAN; Then log into the

camera via LAN and go to System Congfig→Network Config→Port

menu to set up the port number.

2. Enter System Config→Network Config→IP Address menu to modify

the IP address.

4. Open the web browser and input its WAN IP and HTTP port to

access the IP-CAM.

3. Go to the router’s management interface through IE browser to

forward the IP address and port of IP-CAM in the “Virtual Server”.

Other manuals for VTC-TNB42R3F

This manual suits for next models

Table of contents

Other Vitek Security Camera manuals

Vitek

Vitek VTC-C750WDR User manual

Vitek

Vitek VTC-B74 User manual

Vitek

Vitek VTC-T4T3HR2MD User manual

Vitek

Vitek VTC-IRLED30A User manual

Vitek

Vitek VTD-IR2811DN User manual

Vitek

Vitek VT-TPTZ10HR-2A4 User manual

Vitek

Vitek VTD-C510 User manual

Vitek

Vitek Transcendent VT-TPTZ-B10X2A User manual

Vitek

Vitek VTC-IRLED30HD User manual

Vitek

Vitek Transcendent VTC-TNB8RMA3 User manual

Vitek

Vitek VTC-IRH70 User manual

Vitek

Vitek VTC-TTAT2HR2F User manual

Vitek

Vitek VTD-MVHD2812 User manual

Vitek

Vitek VTC-TTAB42R2F User manual

Vitek

Vitek Transcendent Series User manual

Vitek

Vitek VT-PIRC2H User manual

Vitek

Vitek VTC-TNT5RFEA-2 User manual

Vitek

Vitek Virtuoso Series 8 User manual

Vitek

Vitek TRANSCENDENT VT-SMKC2T User manual

Vitek

Vitek VTC-C750/DN User manual

Vitek

Vitek VT-PTZ220N User manual

Vitek

Vitek Transcendent Series User manual

Vitek

Vitek VTC-C2BMS2 User manual

Vitek

Vitek Mighty Series User manual

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Lumens

Lumens VC-A50PNW installation guide